S1117-25D

Semiconductor S1117AD/S1117-xxD Adjustable and Fixed Voltage Regulator Descriptions The S1117 series of positive adjustable and fixed regulators are designed to provide 1A with high efficiency. All internal circuitry is designed to operate down to 1.3V input to output differential. On-chip trimming adjusts reference voltage to 2%. Features • Adjustable or fixed output • Output current of 1A • Low dropout, 1.3V maximum at 1A output current • Thermal shutdown protection Ordering Information Type NO. S1117AD/S1117xxD Marking S1117‫ٱٱ‬D/ S1117‫ٱٱٱ‬D Package Code D-PAK □□:Voltage Code (Aj : 1.25V, 15:1.5V,:18: 1.8V, 25:2.5V, 33:3.3V, 50:5.0V) □□□:Voltage Code (285:2.85V) Outline Dimensions (Unit : mm) BLOCK DIAGRAM PIN Connections 1. GND / Adj. 2,4 Output 3. Input KSD-I6O001-000 1 S1117AD/S1117-xxD Absolute Maximum Ratings Characteristic Input voltage Power Dissipation Junction Temperature Operating temperature range Storage temperature range [Ta=25°C] Symbol VI PD1(Note1) PD2(Note2) TJ Topr Tstg Rating 16 4.5 1.5 150 0 ~ +125 -55 ~ +150 Unit V W °C ℃ °C Note 1 : Mounted on a glass epoxy circuit board of 50.8 × 50.8mm. (at 1oz copper area) Note 2 : No Heat sink Recommended operating conditions Characteristic Input voltage Output current Symbol VI IO Min. VO+1.5V 1 Max. VO+7V 1000 Unit V mA Device Selection Guide Device S1117AD S1117-15D S1117-18D S1117-25D S1117-285D S1117-33D S1117-50D Output Voltage Adjustable 1.50V 1.80V 2.50V 2.85V 3.30V 5.00V Note 3 : Other fixed versions are available VO=1.5V ~ 5V KSD-I6O001-000 2 S1117AD/S1117-xxD Electrical Characteristics (Electrical Characteristics at 0℃≤Ta≤125℃ and VI=(VO+1.5V), Io=10mA, CO=10µF, unless otherwise specified.) Characteristic Symbol Device S1117A Test Condition * VI = (VO+1.5V) to 7V IO = 0 to 1000mA * VI = (VO+1.5V) to 7V IO = 0 to 1000mA * VI = (VO+1.5V) to 7V IO = 0 to 1000mA * VI = (VO+1.5V) to 7V IO = 0 to 1000mA * VI = (VO+1.5V) to 7V IO = 0 to 1000mA * VI = (VO+1.5V) to 7V IO = 0 to 1000mA * VI = (VO+1.5V) to 7V IO = 0 to 1000mA 1.5V≤ VI-VO≤7V IO=10mA 1.5V≤ VI-VO≤7V IO=10mA ~ 1000mA IO=0 VAdj=0V VI = (VO+1.5V) to 7V IO = 100mA 1.5V ≤ VI - VO ≤ 7V IO=10mA ~ 1000mA IO =1000mA IO=1000mA VRipple=1VP-P , f=120 ㎐ IO≥1000mA * * * Min 1.23 1.20 1.47 1.44 1.76 1.73 2.45 2.40 2.79 2.74 3.23 3.17 4.90 4.80 * * - Typ 1.25 Max 1.28 1.30 1.53 Unit S1117-15 1.50 1.56 1.84 S1117-18 1.80 1.87 2.55 V Output voltage VO S1117-25 2.50 2.60 2.91 S1117-285 2.85 3.30 2.96 3.37 3.43 S1117-33 5.00 5.10 5.20 S1117-50 Line regulation (Note4) Load regulation (Note4) Quiescent current Minimum load current Adjust pin current Adjust pin current change Dropout voltage Ripple ratio rejection │△VO(△VI)│ │△VO(△IL) │ IQC I L(MIN) IADJ │∆IADJ│ VDROP RR ILIMIT All All All S1117A S1117A S1117A All All All 5 10 7 3 55 1 10 30 13 7 90 5 1.3 - mV mV mA mA µA µA V dB A 60 1.1 1.2 72 Current limit [ * ] Ta=25℃ Note 4: Low duty pulse testing with Kelvin connections required. KSD-I6O001-000 3 S1117AD/S1117-xxD ■ Typical Applications VI (Fixed Version) S1117-XX VO Adj/GND CI 10㎌ CO 10㎌ RL Fig. 1 Fixed Voltage Regulator VI (Adjustable Version) S1117A Adj Vo=3.5V VO CI 10㎌ IADJ R1 125Ω (1％) R2 225Ω (1％) CO 10㎌ Vo = VADJ × (1 + R2 ) + I ADJ × R 2 R1 Fig. 2 Adjustable Voltage Regulator Notes 5: 1) CI needed if device is far from filter capacitors 2) CO minimum value required for stability KSD-I6O001-000 4 S1117AD/S1117-xxD Electrical Characteristic Curves Fig.3 VDROP vs IO 2.0 1.20 Fig.4 Vo vs Ta Output Voltage Deviation [%] 0.90 0.60 0.30 0.00 -0.3 -0.6 -0.9 -1.2 -25 0 25 50 75 100 125 150 VI=VO+1.5V, IO=500mA Dropout Voltage VDROP [V] 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0 200 400 600 800 1000 Ta=0°C 50°C 125°C Output Current IO [mA] Fig.5 IL(MIN) vs VI-VO Minimum Load Current IL(MIN) [mA] 4.2 3.8 3.4 3.0 2.6 Ta=125℃ 2.2 1.8 1.4 1.0 0 1 2 3 4 5 6 7 8 0℃ 50℃ S1117A, VAdj=0 85 Ambient Temperature Ta [℃] Fig.6 IAdj vs Ta VI=VO+1.5V, IO=100mA Adjust Pin Current IAdj [µA] 80 75 70 65 60 55 45 40 -25 0 25 50 75 100 125 150 Input-Output Differential Voltage [V] Fig.7 PD vs Ta 15 Ambient Temperature Ta [℃] Power dissipation PD [W] 12 TC =2 5° C 9 6 3 0 Mounted on a glass epoxy circuit board of 50.8*50.8 mm (at 1oz copper area) Ta=25℃ 0 25 50 75 100 150 125 Ambient Temperature Ta [˚C] KSD-I6O001-000 5 S1117AD/S1117-xxD The AUK Corp. products are intended for the use as components in general electronic equipment (Office and communication equipment, measuring equipment, home appliance, etc.). Please make sure that you consult with us before you use these AUK Corp. products in equipments which require high quality and / or reliability, and in equipments which could have major impact to the welfare of human life(atomic energy control, airplane, spaceship, transportation, combustion control, all types of safety device, etc.). AUK Corp. cannot accept liability to any damage which may occur in case these AUK Corp. products were used in the mentioned equipments without prior consultation with AUK Corp.. Specifications mentioned in this publication are subject to change without notice. KSD-I6O001-000 6