6N135-000E

Data Sheet 6N135/6, HCNW135/6, HCPL-2502/0500/ 0501 Single-Channel, High-Speed Optocouplers Description These diode-transistor optocouplers use an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output-transistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base-collector capacitance. Features      UL Recognized – 3750 Vrms for 1 minute (5000 Vrms for 1 minute for HCNW and Option 020 devices) per UL1577 These single channel optocoup-lers are available in 8-pin DIP, SO-8, and Widebody package configurations. CSA Approved IEC/EN/DIN EN 60747-5-5 Approved The 6N135, HCPL-0500, and HCNW135 are for use in TTL/CMOS, TTL/LSTTL or wide-bandwidth analog applications. Current transfer ratio (CTR) for these devices is 7% minimum at IF = 16 mA. The 6N136, HCPL-2502, HCPL-0501, and HCNW136 are designed for high-speed TTL/TTL applications. A standard 16-mA TTL sink current through the input LED will provide enough output current for 1 TTL load and a 5.6 k pull-up resistor. CTR for these devices is 19% minimum at IF = 16 mA. High speed: 1 Mb/s TTL compatible Available in 8-pin DIP, SO-8, widebody packages Open collector output Safety approval  – VIORM = 567V peak for SO-8 devices – VIORM = 630V peak for DIP 300 mil devices – VIORM = 1414V peak for DIP 400 mil (widebody) devices Dual channel version available (253X/053X/0534) Applications         High voltage insulation Video signal isolation Line receivers Feedback element in switched mode power supplies High speed logic ground isolation – TTL/TTL, TTL/CMOS, TTL/LSTTL Replaces pulse transformers Replaces slow phototransistor isolators Analog signal ground isolation CAUTION! Take normal static precautions in handling and assembly of this component to prevent damage and/or degradation that may be induced by ESD. Broadcom AV02-0171EN January 30, 2019 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Functional Diagram 8 V CC NC 1 7 VB ANODE 2 CATHODE Schematic 6 VO 3 TRUTH TABLE (POSITIVE LOGIC) LED VO ON LOW OFF HIGH ANODE CATHODE V0 ON LOW OFF HIGH IO 6 VCC + - VO 3 5 SHIELD Truth Table (Positive Logic) LED 8 IF VF 5 GND NC 4 2 I CC 7 GND IB VB A 0.1-µF bypass capacitor must be connected between pins 5 and 8. Selection Guide Minimum CMR dV/dT (V/µs) 1000 VCM (V) 10 Current Transfer Ratio (%) 7 8-Pin DIP (300 Mil) Single Channel Package Dual Channel Packagea Small Outline SO-8 Single Channel Package Dual Channel Packagea Widebody (400 Mil) Single Channel Package 6N135 HCPL-2530 HCPL-0500 HCPL-0530 HCNW135 19 6N136 HCPL-2531 HCPL-0501 HCPL-0531 HCNE136 15 HCPL-2502 a. Technical data for these products are on separate Broadcom publications. Broadcom AV02-0171EN 2 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Ordering Information 6N135, 6N136, HCPL-2502, HCPL-0500, HCPL-0501 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW135 and HCNW136 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All these devices are approved under CSA Component Acceptance Notice #5, File CA 88324. Option Part Number RoHS Compliant Non RoHS Compliant 6N135 6N136 HCPL-2502 -000E No option HCPL-0500 HCPL-0501 HCNW135 HCNW136 -300E #300 -500E #500 -020E #020 -320E Package 300mil DIP-8 Surface Mount Gull Wing X X X #320 X X -520E #520 X X -060E #060 #360 X X -560E #560 X X -000E No option -500E #500 SO-8 X #060 X -560E #560 X #300 -500E #500 X 50 per tube X 1000 per reel X 400 mil Widebody DIP-8 X X -060E No option X X X X X Quantity 50 per tube X 50 per tube X 50 per tube X X -360E -000E UL 5000 Vrms/ IEC/EN/DIN 1 Minute EN Rating 60747-5-5 X X -300E UL 3750 Vrms/ Tape and 1 Minute Reel Rating 1000 per reel X 50 per tube X X 50 per tube X X 1000 per reel X 100 per tube X X 1500 per reel X X 100 per tube X X X 1500 per reel X X 42 per tube X X 42 per tube X X 750 per reel X To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-2502-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: HCPL-2502 to order product of 300 mil DIP package in tube packaging and non RoHS compliant. Optional data sheets are available. Contact your Broadcom® sales representative or authorized distributor for information. NOTE: Broadcom The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use ‘-XXXE‘. AV02-0171EN 3 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Package Outline Drawings 8-Pin DIP Package (6N135/6, HCPL-2502) 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) TYPE NUMBER 8 7 6 A XXXXZ YYWW EEE 1 1.19 (0.047) MAX. 2 3 5 OPTION CODE* 6.35 ± 0.25 (0.250 ± 0.010) DATE CODE RU 4 UL RECOGNITION LOT ID 1.78 (0.070) MAX. 5 q TYP. 3.56 ± 0.13 (0.140 ± 0.005) 4.70 (0.185) MAX. 0.254 + 0.076 - 0.051 + 0.003) (0.010 - 0.002) 0.51 (0.020) MIN. 2.92 (0.115) MIN. 1.080 ± 0.320 (0.043 ± 0.013) Broadcom 0.65 (0.025) MAX. 2.54 ± 0.25 (0.100 ± 0.010) DIMENSIONS IN MILLIMETERS AND (INCHES). *MARKING CODE LETTER FOR OPTION NUMBERS "L" = OPTION 020 "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. AV02-0171EN 4 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N135/6) LAND PATTERN RECOMMENDATION 9.65 ± 0.25 (0.380 ± 0.010) 8 7 6 1.016 (0.040) 5 6.350 ± 0.25 (0.250 ± 0.010) 10.9 (0.430) 1 2 3 4 1.27 (0.050) 1.19 (0.047) MAX. 9.65 ± 0.25 (0.380 ± 0.010) 1.780 (0.070) MAX. 7.62 ± 0.25 (0.300 ± 0.010) 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) 0.635 ± 0.130 (0.025 ± 0.005) + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 0.635 ± 0.25 (0.025 ± 0.010) 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 2.0 (0.080) 12 q NOM. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. Broadcom AV02-0171EN 5 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Small Outline SO-8 Package (HCPL-0500/1) LAND PATTERN RECOMMENDATION 8 7 5 XXX YWW EEE 3.937 ± 0.127 (0.155 ± 0.005) PIN ONE 6 1 2 3 0.406 ± 0.076 (0.016 ± 0.003) 5.994 ± 0.203 (0.236 ± 0.008) TYPE NUMBER (LAST 3 DIGITS) DATE CODE LOT ID 4 * 0.64 (0.025) 7q 1.524 (0.060) TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± 0.254 (0.205 ± 0.010) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. Broadcom 1.9 (0.075) 1.270 BSC (0.050) * 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.125 ± 0.005) 7.49 (0.295) 45 q X 0.432 (0.017) 0 ~ 7q 0.228 ± 0.025 (0.009 ± 0.001) 0.203 ± 0.102 (0.008 ± 0.004) 0.305 MIN. (0.012) AV02-0171EN 6 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers 8-Pin Widebody DIP Package (HCNW135/6) 11.00 MAX. (0.433) 11.23 ± 0.15 (0.442 ± 0.006) 8 7 6 TYPE NUMBER A HCNWXXXX YYWW EEE 1 9.00 ± 0.15 (0.354 ± 0.006) 5 DATE CODE LOT ID 2 3 4 10.16 (0.400) TYP. 1.55 (0.061) MAX. 7 q TYP. 5.10 MAX. (0.201) 3.10 (0.122) 3.90 (0.154) 2.54 (0.100) TYP. 1.8 ± 0.15 (0.071 ± 0.006) Broadcom 0.40 (0.016) 0.56 (0.022) + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) 0.51 (0.021) MIN. DIMENSIONS IN MILLIMETERS (INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. AV02-0171EN 7 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers 8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW135/6) 11.23 ± 0.15 (0.442 ± 0.006) 8 7 6 LAND PATTERN RECOMMENDATION 5 9.00 ± 0.15 (0.354 ± 0.006) 1 2 3 13.56 (0.534) 4 2.29 (0.09) 1.3 (0.051) 12.30 ± 0.30 (0.484 ± 0.012) 1.55 (0.061) MAX. 11.00 MAX. (0.433) + 0.003) 4.00 MAX. (0.158) 1.80 ± 0.15 (0.071 ± 0.006) 0.75 ± 0.25 (0.030 ± 0.010) 2.54 (0.100) BSC + 0.076 0.254 - 0.0051 (0.010 - 0.002) 1.00 ± 0.15 (0.039 ± 0.006) 7 q NOM. DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. Solder Reflow Profile Recommended reflow conditions are as per JEDEC Standard, J-STD-020 (latest revision). Non-halide flux should be used. Regulatory Information The devices contained in this data sheet have been approved by the following organizations: UL Approval under UL 1577, Component Recognition Program, File E55361. CSA Approval under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-5 (HCNW and Option 060/360/560 only) Broadcom AV02-0171EN 8 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Insulation and Safety Related Specifications Symbol 8-Pin DIP (300 Mil) Value SO-8 Value Widebody (400 Mil) Value Units Conditions Minimum External Air Gap (External Clearance) L(101) 7.1 4.9 9.6 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (External Creepage) L(102) 7.4 4.8 10.0 mm Measured from input terminals to output terminals, shortest distance path along body.. Minimum Internal Plastic Gap (Internal Clearance) 0.08 0.08 1.0 mm Through insulation distance conductor to conductor, usually the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Minimum Internal Tracking (Internal Creepage) N/A N/A 4.0 mm Measured from input terminals to output terminals, along internal cavity. 200 200 200 V IIIa IIIa IIIa Parameter Tracking Resistance (Comparative Tracking Index) Isolation Group CTI DIN IEC 112/VDE 0303 Part 1 Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 – Surface mount classification is Class A in accordance with CECC 00802. Broadcom AV02-0171EN 9 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers IEC/EN/DIN EN 60747-5-5 Insulation Characteristicsa (Option 060 Only) Description Symbol Installation Classification per DIN VDE 0110/39, Table 1 for rated mains voltage  150 Vrms for rated mains voltage  300 Vrms for rated mains voltage  600 Vrms Climatic Classification Pollution Degree (DIN VDE 0110/39) 8-Pin DIP SO-8 I – IV I – IV I – IV I – IV I – IV I – III 0/70/21 0/70/21 Units 2 2 VIORM 630 567 Vpeak Input to Output Test Voltage, Method ba VIORM × 1.875 = VPR, 100% Production Test with tm = 1s, Partial Discharge < 5 pC VPR 1181 1063 Vpeak Input to Output Test Voltage, Method aa VIORM x 1.6 = VPR, Type and Sample Test, tm = 10s, Partial Discharge < 5 pC VPR 1008 907 Vpeak VIOTM 8000 6000 Vpeak TS IS, INPUT PS, OUTPUT 175 230 600 150 150 600 °C mA mW RS ≥109 ≥109  Maximum Working Insulation Voltage Highest Allowable Overvoltagea (Transient Overvoltage tini = 60s) Safety-limiting values – Maximum Values Allowed in the Event of a Failure Case Temperature Input Current Output Power Insulation Resistance at TS, VIO = 500V a. Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for a detailed description. NOTE: Broadcom Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in the application. AV02-0171EN 10 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers IEC/EN/DIN EN 60747-5-5 Insulation Characteristicsa (HCNW135/6 Option 060 Only) Description Symbol Installation Classification per DIN VDE 0110/39, Table 1 for rated mains voltage  150 Vrms Characteristic Units I – IV I – IV I – IV I – III for rated mains voltage  300 Vrms for rated mains voltage  600 Vrms for rated mains voltage  1000 Vrms Climatic Classification 0/70/21 Pollution Degree (DIN VDE 0110/39) 2 Maximum Working Insulation Voltage VIORM 1414 Vpeak ba Input to Output Test Voltage, Method VIORM × 1.875 = VPR, 100% Production Test with tm = 1s, Partial Discharge < 5 pC VPR 2651 Vpeak Input to Output Test Voltage, Method aa VIORM x 1.6 = VPR, Type and Sample Test, tm = 10s, Partial Discharge < 5 pC VPR 2262 Vpeak VIOTM 8000 Vpeak TS IS, INPUT PS, OUTPUT 150 400 700 °C mA mW RS ≥109  Highest Allowable Overvoltagea (Transient Overvoltage tini = 60s) Safety-limiting values – Maximum Values Allowed in the Event of a Failure Case Temperature Input Current Output Power Insulation Resistance at TS, VIO = 500V a. Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for a detailed description. NOTE: Broadcom Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in the application. AV02-0171EN 11 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Absolute Maximum Rating Parameter Symbol Storage Temperaturea TS Operating Temperaturea TA Average Forward Input Currenta IF(AVG) Peak Forward Input Currenta (50% duty cycle, 1-ms pulse width) IF(PEAK) 50% duty cycle, 1 ms pulse width Peak Transient Input Currenta (1-µs pulse width, 300 pps) Reverse LED Input Voltagea (Pin 3-2) IF(TRANS) VR PIN Input Power Dissipationa Device Min. Max. Units –55 125 °C 8-Pin DIP SO-8 –55 100 °C Widebody –55 85 — 25 mA b 8-Pin DIP SO-8 — 50 mA c Widebody — 40 8-Pin DIP SO-8 — 1 Widebody — 0.1 8-Pin DIP SO-8 — 5 Widebody — 3 8-Pin DIP SO-8 — 45 Widebody A V mW — 40 IO(AVG) — 8 mA IO(PEAK) — 16 mA Emitter-Base Reverse Voltagea (Pin 5-7) VEBR — 5 V Supply Voltage (Pin 8-5) VCC –0.5 30 V Output Voltage (Pin 6-5) VO –0.5 20 V Supply Voltagea (Pin 8-5) VCC –0.5 15 V Output Voltagea (Pin 6-5) VO –0.5 15 V Base Currenta (Pin 7) IB — 5 mA Output Power Dissipationa PO — 100 mW Lead Solder Temperaturea (Through-Hole Parts Only) 1.6 mm below seating plane, 10s up to seating plane, 10s TLS — 260 °C 260 °C Reflow Temperature Profile TRP Average Output Currenta (Pin 6) Peak Output Currenta 8-Pin DIP Widebody SO-8 and Option 300 Note d e See Package Outline Drawings a. Data has been registered with JEDEC for the 6N135/6N136. b. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8). c. Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8). d. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8). e. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8). Broadcom AV02-0171EN 12 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Electrical Specifications (DC) Over recommended operating temperature (TA = 0°C to 70°C) and unless otherwise specified. See note. Parameter Current Transfer Ratio Symbol b CTR Device Min. Typ.a Max. Units 6N135 HCPL-0500 HCNW135 7 18 50 % 5 19 — VO = 0.5V 22 TA = 25°C VO = 0.4V HCPL-2502 6N136 HCPL-0501 HCNW136 Logic Low Output Voltage VOL 6N135 HCPL-0500 HCNW135 6N136 HCPL-2502 HCPL-0501 HCNW136 Logic High Output Current IOHb 15 Test Conditions TA = 25°C VO = 0.4V 15 25 — VO = 0.5V 19 24 50 15 25 — TA = 25°C VO = 0.4V VO = 0.5V — 0.1 0.4 — 0.1 0.5 — 0.1 0.4 — 0.1 0.5 — 0.003 0.5 — 0.01 1 TA = 25°C VO = VCC = 15V — — 50 VO = VCC = 15V V IF = 16 mA, VCC = 4.5V µA TA = 25°C VO = VCC = IF = 0 mA 5.5V — 50 200 µA IF = 16 mA, VO = Open, VCC = 15V Logic High Supply Current ICCHb — 0.02 1 µA TA = 25°C IF = 0 mA, VO = Open — — 2 8-Pin DIP — 1.5 1.7 SO-8 — — 1.8 Widebody 1.45 1.68 1.85 1.35 — 1.95 5 — — Widebody 3 — — 8-Pin DIP — –1.6 Widebody — –1.9 8-Pin DIP — 60 — — 90 — Input Reverse Breakdown Voltage Temperature Coefficient of Forward Voltage Input Capacitance BVR b VF/TA 8-Pin DIP 7 VCC = 15V V TA = 25°C IF = 16 mA 3 TA = 25°C IF = 16 mA V IR = 10 µA IR = 100 µA mV/°C IF = 16 mA pF f = 1 MHz, VF = 0V SO-8 Widebody Broadcom c, d SO-8 SO-8 CIN 1, 2, 4 TA = 25°C IO = 3.0 mA IO = 2.4 mA ICCL VFb Note TA = 25°C IO = 1.1 mA IF = 16 mA, IO = 0.8 mA VCC = 4.5V Logic Low Supply Current Input Forward Voltage Figure AV02-0171EN 13 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Parameter Transistor DC Current Gain Single-Channel, High-Speed Optocouplers Symbol Device Min. Typ.a Max. hFE 8-Pin DIP — 150 — VO = 5V, IO = 3 mA Widebody — 180 — VO = 5V, IO = 3 mA — 160 — VO = 0.4V, IB = 20 µA Units Test Conditions Figure Note a. All typicals at TA = 25°C. b. For JEDEC registered parts. c. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100. d. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Avago guarantees a minimum CTR of 19%. NOTE: Broadcom Use of a 0.1-µf bypass capacitor connected between pins 5 and 8 is recommended. AV02-0171EN 14 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Switching Specifications (AC) Over recommended temperature (TA = 0°C to 70°C), VCC = 5V, IF = 16 mA unless otherwise specified. Parameter Symbol Device Min. Typ.a Max. Units Propagation Delay Time to Logic Low at Output tPHLb 6N135 HCPL-0500 HCNW135 — 0.2 1.5 µs 6N136 HCPL-2502 HCPL-0501 HCNW136 — 0.2 0.8 — — 1.0 6N135 HCPL-0500 HCNW135 — 1.3 1.5 — — 2.0 Propagation Delay Time to Logic High at Output Common Mode Transient Immunity at Logic High Level Output Common Mode Transient Immunity at Logic Low Level Output Bandwidth tPLHb |CMH| |CML| BW 6N136 HCPL-2502 HCPL-0501 HCNW136 — 0.6 0.8 — — 1.0 6N135 1 — — HCPL-0500 HCNW135 — 1 — 6N136 1 — — HCPL-2502 HCPL-0501 — 1 — 6N135 1 — — HCPL-0500 HCNW135 — 1 — 6N136 1 — — HCPL-2502 HCPL-0501 — 1 — 6N135/6 HCPL-2502 HCPL-0500/1 — 9 — HCNW135/6 — 11 — Figure Note 5, 6, 11 c, d 5, 6, 11 c, d kV/µs RL = 4.1 k IF = 0 mA, TA = 25°C, VCM = 10 Vp-p, RL = 1.9 k CL = 15 pF 12 c, d, e kV/µs RL = 4.1 k IF = 16 mA, TA = 25°C, CL = 15 pF 12 c, d, e 8, 10 f µs Test Conditions TA = 25°C RL = 4.1 k TA = 25°C RL = 1.9 k TA = 25°C RL = 4.1 k TA = 25°C RL = 1.9 k RL = 1.9 k MHz See Test Circuit a. All typicals at TA = 25°C. b. For JEDEC registered parts. c. The 1.9 k load represents 1 TTL unit load of 1.6 mA and the 5.6 k pull-up resistor. d. The 4.1 k load represents 1 LSTTL unit load of 0.36 mA and 6.1 kpull-up resistor. e. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic High state (that is, VO > 2.0V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic Low state (that is, VO < 0.8 V). f. The frequency at which the ac output voltage is 3 dB below its mid-frequency value. Broadcom AV02-0171EN 15 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Package Characteristics Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. Parameter Input-Output Momentary Withstand Voltageb Sym. Device Min. Typ.a Max. Units VISO 8-Pin DIP SO-8 3750 — — Vrms Widebody 5000 — — c e 8-Pin DIP (Option 020) 5000 — — c e f II-O 8-Pin DIP — — 1 µA 45% RH, t = 5s, VI-O = 3 kVdc, TA = 25°C RI-O 8-Pin DIP SO-8 — 1012 —  VI-O = 500 Vdc Widebody 1012 1013 — TA = 25°C 1011 — — TA = 100°C 8-Pin DIP SO-8 — 0.6 — Widebody — 0.5 0.6 Input-Output Resistance Input-Output Capacitance CI-O Test Conditions Figure RH < 50%, t = 1 min., TA = 25°C Note c, d , , , pF c, g c f = 1 MHz c a. All typicals at TA = 25°C. b. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074, Optocoupler Input-Output Endurance Voltage, publication number 5963-2203E. c. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together. d. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 Vrms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table if applicable. e. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 Vrms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table if applicable. f. Refer to the Option 020 data sheet for more information. g. This rating is equally validated by an equivalent ac proof test. Broadcom AV02-0171EN 16 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Figure 1: DC and Pulsed Transfer Characteristics WIDEBODY 16 40 mA T = 25q C 10 VA = 5.0 V CC IO Ð OUTPUT CURRENT Ð mA IO Ð OUTPUT CURRENT - mA 8 PIN DIP, SO-8 35 mA 30 mA 25 mA 5 20 mA 15 mA 10 mA 0 TA = 25q C VCC = 5.0 V 40 mA 12 35 mA 30 mA 25 mA 8 20 mA 15 mA 4 10 mA IF = 5 mA IF = 5 mA 0 10 0 20 0 10 VO - OUTPUT VOLTAGE - V 20 VO - OUTPUT VOLTAGE - V Figure 2: Current Transfer Ratio vs. Input Current 6N135, HCPL-0500 6N136, HCPL-2502 HCPL-0501 1.0 0.5 NORMALIZED I F = 16 mA VO = 0.4 V VCC = 5 V TA = 25q C 0.1 0 1 10 100 WIDEBODY NORMALIZED CURRENT TRANSFER RATIO NORMALIZED CURRENT TRANSFER RATIO 8 PIN DIP, SO-8 1.5 1.5 HCNW135/6 1.0 0.5 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 4.5 V TA = 25 q C 0 0 1 IF - INPUT CURRENT - mA 10 100 IF - INPUT CURRENT - mA Figure 3: Input Current vs. Forward Voltage 8 PIN DIP, SO-8 WIDEBODY 1000 100 IF TA = 25q C + VF - 10 1.0 IF - FORWARD CURRENT - mA IF - FORWARD CURRENT - mA 1000 0.1 0.01 0.001 1.1 1.2 1.3 1.4 1.5 VF - FORWARD VOLTAGE - VOLTS Broadcom 1.6 TA = 25q C 100 10 1.0 IF 0.1 + VF - 0.01 0.001 1.2 1.3 1.4 1.5 1.6 1.7 1.8 VF - FORWARD VOLTAGE - VOLTS AV02-0171EN 17 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers 8 PIN DIP, SO-8 1.1 1.0 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25q C 0.9 0.8 6N135, HCPL-0500 6N136, HCPL-2502, HCPL-0501 0.7 0.6 -60 -40 -20 0 20 40 60 80 100 WIDEBODY NORMALIZED CURRENT TRANSFER RATIO NORMALIZED CURRENT TRANSFER RATIO Figure 4: Current Transfer Ratio vs. Temperature 1.1 1.0 HCNW135/6 0.9 0.8 0.7 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25q C 0.6 0.5 0.4 -60 -40 -20 TA - TEMPERATURE - q C 0 20 40 80 100 60 TA - TEMPERATURE - q C Figure 5: Propagation Delay vs. Temperature WIDEBODY 8 PIN DIP, SO-8 IF = 16 mA, VCC = 5.0 V 6N135, HCPL-0500 (RL = 4.1 k: 6N136, HCPL-0501, HCPL-2502 (RL = 1.9 k:) 1500 1000 tPLH tPHL 500 0 -60 -20 20 60 1000 tp - PROPAGATION DELAY - ns tp - PROPAGATION DELAY - ns 2000 IF = 16 mA, VCC = 5.0 V HCNW135 (RL = 4.1 k: HCNW136 (RL = 1.9 k: 800 600 t PLH 200 0 -60 -40 -20 100 t PHL 400 0 20 40 60 80 100 TA - TEMPERATURE - q C TA - TEMPERATURE - q C Figure 6: Propagation Delay Time vs. Load Resistance WIDEBODY 8 PIN DIP, SO-8 2.0 10.0 I F = 10 mA I F = 16 mA VCC = 5.0 V TA = 25q C 1.0 0.8 0.6 tPLH 0.4 t PHL 0.2 0.1 1 2 3 4 5 6 7 8 9 10 RL - LOAD RESISTANCE - (k:) Broadcom tP - PROPAGATION DELAY - μs tP - PROPAGATION DELAY - μs 3.0 I F = 10 mA I t = 16 mA 6.0 4.0 VCC = 5.0 V TA = 25q C t PLH 1.0 0.6 t PHL 0.4 0.2 0.1 1 2 4 10 40 100 RL - LOAD RESISTANCE - (k:) AV02-0171EN 18 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers 8 PIN DIP, SO-8 10+4 IF = 0 VO = VCC = 5.0 V 10+3 10+2 10+1 100 10 -1 10 -2 -75 -50 -25 0 +25 +50 +75 +100 IOH - LOGIC HIGH OUTPUT CURRENT - nA IOH - LOGIC HIGH OUTPUT CURRENT - nA Figure 7: Logic High Output Current vs. Temperature WIDEBODY +3 10 IF = 0 VO = VCC = 15 V +2 10 +1 10 0 10 -60 -40 -20 0 20 40 60 80 100 TA - TEMPERATURE - q C TA - TEMPERATURE - q C 8 PIN DIP, SO-8 0.30 IO I F - SMALL SIGNAL CURRENT TRANSFER RATIO IO I F - SMALL SIGNAL CURRENT TRANSFER RATIO Figure 8: Small-Signal Current Transfer Ratio vs. Quiescent Input Current WIDEBODY 0.50 TA = 25q C, RL = 100 :, VCC = 5 V TA = 25q C, RL = 100 :, VCC = 5 V 0.40 0.20 0.30 0.20 0.10 0.10 0 0 4 8 12 16 20 25 IF - QUIESCENT INPUT CURRENT - mA 0 0 4 8 12 16 20 25 IF - QUIESCENT INPUT CURRENT - mA 8-PIN DIP/S0-8 800 PS (mW) IS (mA) For 8-PIN DIP IS (mA) For S0-8 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 200 TS - CASE TEMPERATURE - q C Broadcom OUTPUT POWER - PS, INPUT CURRENT - IS OUTPUT POWER - PS, INPUT CURRENT - IS Figure 9: Thermal Derating Curve, Dependence of Safety Limiting Value with Case Temperature per IEC/EN/DIN EN 60747-5-5 HCNW135/6 1000 PS (mW) 900 IS (mA) 800 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 TS - CASE TEMPERATURE - q C AV02-0171EN 19 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers Figure 10: Frequency Response 6N135/6, HCPL-0500/1, HCPL-2502 NORMALIZED RESPONSE - dB +5 6N135/6, HCPL-0500/1, HCPL-2502 +12 V TA = 25qC 1 0.1 μF +12 V 8 2.1 K: 0 15 K: 2 1.2 K: Q3 9.1 K: -5 47 μF VFF 100 : 3 1N4150 -20 0.1 1.0 10 5 22 : TRIM FOR UNITY GAIN 470: 100 : RT 51 : VO Q2 0.1 μF 4 1 K: -15 6 Q1 -10 0.1 μF 7 (1 M: 12 pF TEST INPUT) Q 1 , Q 2 , Q 3 : 2N3904 TYPICAL LINEARITY = ± 3% AT V IN = 1 V p-p TYPICAL SNR = 50dB TYPICAL R T = 375 : TYPICAL VO dc = 3.8 V TYPICAL I F = 9 mA 100 f - FREQUENCY - MHz Figure 11: Switching Test Current IF 0 5V VO 1.5 V PULSE GEN. ZO = 50 : t r = 5 ns IF 10% DUTY CYCLE 1/f < 100 μS 1.5 V VOL 1 8 2 7 3 6 RL VO 0.1μF I F MONITOR 4 5 CL = 1.5 μF RM t PLH t PHL +5 V Figure 12: Test Circuit for Transient Immunity and Typical Waveforms IF VCM 10% 0V 90% 90% tr 1 8 2 7 3 6 +5 V B 10% tf RL A VO 5V VO SWITCH AT B: I F = 16 mA VO 0.1 μF SWITCH AT A: I F = 0 mA VFF 4 5 VOL VCM + - PULSE GEN. Broadcom AV02-0171EN 20 Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, and the A logo are among the trademarks of Broadcom and/or its affiliates in the United States, certain other countries, and/or the EU. Copyright © 2014–2019 Broadcom. All Rights Reserved. The term “Broadcom” refers to Broadcom Inc. and/or its subsidiaries. For more information, please visit www.broadcom.com. Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does not assume any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. 6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Broadcom Single-Channel, High-Speed Optocouplers AV02-0171EN 22