ACNW261L-500E

ACPL-061L, ACPL-C61L and ACNW261L Ultra Low Power 10 MBd Digital CMOS Optocoupler Data Sheet Description Features The ACPL-061L/ACPL-C61L/ACNW261L is an optically coupled optocoupler that combines an AlGaAs light emitting diode and an integrated high gain photo detector addresses the low power need. The optocoupler consumes extremely low power, at maximum 1.5 mA IDD per channel across temperature. The forward current is as low as 1.6 mA to 4 mA and allows direct current drive by most microprocessors. • Ultra low current IDD consumption: 1.5 mA max These optocouplers support both 3.3 V and 5 V supply voltage with guaranteed AC and DC operational parameters from temperature range -40° C to +105° C. The output of the detector IC is a CMOS output. An enable input allows the detector output to be strobed. The internal Faraday shield provides a guaranteed common mode transient immunity specification of 20 kV/μs. • 20 kV/μs minimum Common Mode Rejection (CMR) at VCM = 1000 V The CMOS output is slew-rate controlled and is designed to allow the rise time and fall time to be controlled over a wide range of the load capacitance. This unique design provides maximum AC and DC circuit isolation while achieving TTL/CMOS compatibility. These optocouplers are suitable for high speed logic interfacing, while consuming extremely low power. Functional Diagram TRUTH TABLE (POSITIVE LOGIC) 1 8 VDD Anode 2 7 VE LED 6 VO ON OFF ON H H L H L Z 5 GND OFF L Z ON OFF NC NC L H 3 NC 4 Shield • Available packages: SO-8, Stretched SO-8 and 400 mil widebody • Built-in slew-rate controlled output • Tri-state output with enable pin VE • High Speed: 10 MBd min • Guaranteed AC and DC performance over wide temperature: -40° C to +105° C • Safety and Regulatory Approval – UL 1577 recognized – 3750 Vrms for 1 minute for ACPL-061L and 5000 Vrms for 1 minute for ACPL-C61L/ACNW261L – CSA Approval – IEC/EN/DIN EN 60747-5-5 Approval for Reinforced Insulation Applications • Communication Interface: RS485, CANBus, I2C NC Cathode • Low input current capability: 1.6 mA min (ACPL-061L), 3 mA min (ACPL-C61L), 4 mA min (ACNW261L) • Microprocessor System Interfaces • Digital isolation for A/D, D/A conversion ENABLE OUTPUT A 0.1 μF bypass capacitor must be connected between pins VDD and GND CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The components featured in this datasheet are not to be used in military or aerospace applications or environments. Ordering Information ACPL-061L is UL Recognized with 3750 Vrms for 1 minute per UL1577. ACPL-C61L and ACNW261L are UL Recognized with 5000 Vrms for 1 minute per UL1577. Option Part number (RoHS Compliant) Package Surface Mount ACPL-061L -000E SO-8 X ACPL-C61L X -500E X X -560E X X -000E Stretched SO-8 UL 1577 5000 Vrms / IEC/EN/DIN EN 1 Minute rating 60747-5-5 Quantity 100 per tube -060E -060E ACNW261L Gull Wing Tape & Reel X X 1500 per reel X X X 100 per tube X 1500 per reel 80 per tube X 80 per tube -500E X X X -560E X X X X 1000 per reel X X 42 per tube X X 42 per tube X X 750 per reel -000E -300E -500E 400 mil DIP-8 X X X X X 1000 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-061L-560E to order product of Small Outline SO-8 package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. 2 Package Outline Drawing LAND PATTERN RECOMMENDATION ACPL-061L SO-8 Package 3.937 ± 0.127 (0.155 ± 0.005) DEVICE PART NUMBER LEAD-FREE 8 PIN 1 7 6 5 NNNN Z YYWW • EEE 1 2 3 TEST RATING CODE LOT ID 4 0.406 ± 0.076 (0.016 ± 0.003) 7.49 (0.295) DATE CODE 5.994 ± 0.203 (0.236 ± 0.008) 1.9 (0.075) 1.270 BSC (0.050) 0.64 (0.025) * 5.080 ± 0.127 (0.200 ± 0.005) 0.432 45° X (0.017) 7° 3.175 ± 0.127 (0.125 ± 0.005) 0 ~ 7° 1.524 (0.060) * Total package length (inclusive of mold flash) 5.207 ± 0.254 (0.205 ± 0.010) 0.228 ± 0.025 (0.009 ± 0.001) 0.305 MIN. (0.012) Notes: Lead coplanarity = 0.10 mm (0.004 inches) max. Floating lead protrusion is 0.15 mm (6 mils) max. Option number 500 not marked 0.203 ± 0.102 (0.008 ± 0.004) Dimensions in Millimeters (Inches) ACPL-C61L Stretched SO-8 Package 5.850±0.254 (0.230±0.010) 8 7 6 LAND PATTERN RECOMMENDATION 5 PART NUMBER ROHS-COMPLIANCE INDICATOR DATE CODE NNNN YYWW EEE 1 2 3 12.650 (0.5) Lot ID 6.807±0.127 (0.268±0.005) 1.905 (0.1) 4 0.450 (0.018) 7° 7° 45° 3.180±0.127 (0.125±0.005) 1.270 (0.050) BSG 0.381±0.13 (0.015±0.005) Dimensions in Millimeters (Inches). Lead coplanarity = 0.1 mm (0.004 inches). 3 1.590±0.127 (0.063±0.005) 0.254±0.100 (0.010±0.004) 0.750±0.250 (0.0295±0.010) 11.5±0.250 (0.453±0.010) ACNW261L 8-Pin Widebody DIP Package 11.00 MAX. (0.433) 11.23 ± 0.15 (0.442 ± 0.006) 7 8 5 TEST RATING CODE • LEAD-FREE 1 3 2 9.00 ± 0.15 (0.354 ± 0.006) AVAGO A NNNNNNNN Z YYWW EEE DEVICE PART NUMBER PIN 1 6 DATE CODE LOT ID 4 10.16 (0.400) TYP. 1.55 (0.061) MAX. 7° TYP. + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) 5.10 MAX. (0.201) 3.10 (0.122) 3.90 (0.154) 2.54 (0.100) TYP. 1.80 ± 0.15 (0.071 ± 0.006) 0.51 (0.021) MIN. DIMENSIONS IN MILLIMETERS (INCHES). 0.40 (0.016) 0.56 (0.022) NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. ACNW261L 8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300E LAND PATTERN RECOMMENDATION 11.15 ± 0.15 (0.442 ± 0.006) 8 7 6 5 13.56 (0.534) 9.00 ± 0.15 (0.354 ± 0.006) 1 2 3 4 1.3 (0.051) 1.55 MAX. (0.061) 12.30 ± 0.30 (0.484 ± 0.012) 11.00 MAX. (0.433) 4.00 MAX. (0.158) 1.78 ± 0.15 (0.070 ± 0.006) 2.54 BSC (0.100) 0.75 ± 0.25 (0.030 ± 0.010) Notes: Lead coplanarity = 0.10 mm (0.004 inches) Floating lead protrusion is 0.25 mm (10 mils) max. 4 1.00 ± 0.15 (0.039 ± 0.006) 2.29 (0.09) +0.076 - 0.0051 +0.003) (0.010 - 0.002) 0.254 7° NOM. Dimensions in millimeters (inches) Solder Reflow Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used. Regulatory Information The ACPL-061L, ACPL-C61L, ACNW261L and are pending approval by the following organizations: IEC/EN/DIN EN 60747-5-5 (Option 060E only) UL Approval under UL 1577, component recognition program up to VISO = 3750 VRMS for ACPL-061L and VISO = 5000 VRMS for ACPL-C61L/ACNW261L File E55361. CSA Approval under CSA Component Acceptance Notice #5, File CA 88324. Insulation and Safety Related Specifications Parameter Symbol ACPL-061L ACPL-C61L ACNW261L Unit Conditions Minimum External Air Gap (External Clearance) L(101) 4.9 8 9.6 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (External Creepage) L(102) 4.8 8 10 mm Measured from input terminals to output terminals, shortest distance path along body. 0.08 0.5 1.0 mm Through insulation distance conductor to conductor, usually the straight line distance thickness between the emitter and detector. 175 175 175 V DIN IEC 112/VDE 0303 Part 1 IIIa IIIa IIIa Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) Isolation Group 5 CTI Material Group (DIN VDE 0110, 1/89, Table 1) IEC/EN/DIN EN 60747-5-5 Insulation Characteristics* (Option 060) Characteristic Description Symbol ACPL-061L ACPL-C61L ACNW261L Installation classification per DIN VDE 0110/39, Table 1 for rated mains voltage ≤ 150 Vrms for rated mains voltage ≤ 300 Vrms for rated mains voltage ≤ 600 Vrms for rated mains voltage ≤ 1000 Vrms I – IV I – III I – II I – IV I – IV I – IV I – III I – IV I – IV I – IV I – III Climatic Classification 55/105/21 55/105/21 55/105/21 2 2 2 567 1414 1414 Vpeak Input to Output Test Voltage, Method b* VPR VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial discharge < 5 pC 1063 2651 2651 Vpeak Input to Output Test Voltage, Method a* VIORM x 1.6 = VPR, Type and Sample Test, tm = 10 sec, Partial discharge < 5 pC VPR 907 2262 2262 Vpeak Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec) VIOTM 6000 8000 8000 Vpeak Safety-limiting values – maximum values allowed in the event of a failure. Case Temperature Input Current** Output Power** TS IS, INPUT PS, OUTPUT 150 150 600 175 230 600 150 400 700 °C mA mW Insulation Resistance at TS, VIO = 500 V RS >109 >109 >109 W Pollution Degree (DIN VDE 0110/39) Maximum Working Insulation Voltage VIORM Unit * Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/EN/ DIN EN 60747-5-5) for a detailed description of Method a and Method b partial discharge test profiles. ** Refer to the following figure for dependence of PS and IS on ambient temperature. POWER OUTPUT – PS, INPUT CURRENT – IS POWER OUTPUT – PS, INPUT CURRENT – IS 600 400 200 0 6 PS (mW) IS (mA) 800 0 25 50 75 100 125 150 TS – CASE TEMPERATURE – °C Surface Mount SSO-8 Product 700 175 PS (mW) IS (mA) 600 500 400 300 200 100 0 0 25 50 75 100 125 150 TS – CASE TEMPERATURE – °C 175 200 Widebody 400mil DIP-8 Product 1000 POWER OUTPUT – PS, INPUT CURRENT – IS Surface Mount SO-8 Product 1000 PS (mW) IS (mA) 900 800 700 600 500 400 300 200 100 0 0 25 50 75 100 125 TS – CASE TEMPERATURE – °C 150 175 Absolute Maximum Ratings Parameter Symbol Min. Max. Units Note Storage Temperature TS -55 125 °C Operating Ambient Temperature TA -40 105 °C Reversed Input Voltage VR 5 V Supply Voltage VDD 6.5 V Average Forward Input Current IF – 8 mA Peak Transient Input Current IF(TRAN) – 1 A < 1 ms Pulse Width, < 300 pulses per second 80 mA < 1 ms Pulse Width, 0) away from LED anode through CLA away from LED cathode through CLC increased decreased negative (