ACPL-M49U-000E

ACPL-M49U Wide Operating Temperature R2CouplerTM 20kBd Digital Optocoupler Configurable as Low Power, Low Leakage Phototransistor Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features The ACPL-M49U is a single channel, high temperature, high CMR, 20kBd digital optocoupler, configurable as a low power, low leakage phototransistor, specifically for use in industrial applications. The SO-5 JEDEC registered (MO-155) package outline is surface mountable.  High Temperature and Reliable low speed digital interface for Industrial Application.  30 kV/s High Common-Mode Rejection at VCM = 1500 V (typ)  Low Power, Low Leakage Phototransistor in a 4-Pin Configuration  Compact, Auto-Insertable SO5 Packages  Wide Temperature Range: -40°C ~ 125°C  Low LED Drive Current: 4mA (typ)  Propagation Delay: 20s (max)  Worldwide Safety Approval: – UL 1577, 3750 VRMS /1 min. – CSA File CA88324, Notice #5 – IEC/EN/DIN EN 60747-5-5 This digital optocoupler uses an insulating layer between the light emitting diode and an integrated photo detector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output transistor collector in a 5-pin configuration increase the speed up to a hundred times over that of a conventional phototransistor by reducing the base-collector capacitance. Common connections with the supply and output pins shorted in a 4-pin configuration delivers low power, low leakage performance as a phototransistor. The ACPL-M49U has an increased common mode transient immunity of 15kV/s minimum at VCM = 1500V over extended temperature range. Applications  Low Speed Digital Signal isolation Interface  Inverter fault feedback signal isolation  Switching Power Supplies feedback circuit Avago R2Coupler isolation products provide the reinforced insulation and reliability needed for critical in high temperature industrial applications. Functional Diagrams SHIELD ANODE + 1 VF CATHODE ICC 6 IF ANODE IO 5 VO 3 SHIELD VCC 4 Note: The connection of a 0.1 F bypass capacitor between pins 4 and 6 is recommended for 5-pin configuration 1 6 IF VCC IO VF CATHODE GND + ICC 3 4 GND Note: Pins 5 and 6 are externally shorted for 4-pin configuration. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. LED Vo ON LOW OFF HIGH Ordering Information Option Part Number (RoHS) Compliant Package Surface Mount ACPL-M49U -000E SO-5 X -500E X Tape & Reel Quantity 100 per tube X 1500 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example: ACPL-M49U-500E to order product of Mini-flat Surface Mount 5-pin package in Tape and Reel packaging with RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Package Outline Drawings ACPL-M49U Small Outline SO-5 Package (JEDEC MO-155) M49U YWW 4.4 ± 0.1 (0.173 ± 0.004) ANODE 1 7.0 ± 0.2 (0.276 ± 0.008) CATHODE 3 6 VCC 5 VOUT 4 GND 0.4 ± 0.05 (0.016 ± 0.002) 3.6 ± 0.1* (0.142 ± 0.004) 2.5 ± 0.1 (0.098 ± 0.004) 1.27 BSC (0.050) 0.102 ± 0.102 (0.004 ± 0.004) 0.20 ± 0.025 (0.008 ± 0.001) Dimensions in Millimeters (Inches) * Maximum mold flash on each side is 0.15 mm (0.006) Note: Floating lead protrusion is 0.15 mm (6 mils) max. 2 7° MAX. 0.71 MIN (0.028) MAX. LEAD COPLANARITY = 0.102 (0.004) Land Pattern Recommendation Land Pattern Recommendation (4-pin Configuration) 4.4 (0.17) 4.4 (0.17) 1.3 (0.05) 2.5 (0.10) 2.0 (0.080) 8.27 (0.325) 1.92 (0.075) 0.64 (0.025) 2.5 (0.10) 2.0 (0.080) 0.64 (0.025) 0.64 (0.025) 8.27 (0.325) Dimension in Millimeters (Inches) Dimension in Millimeters (Inches) Recommended Pb-Free IR Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Note: Non-halide flux should be used. Regulatory Information The ACPL-M49U is approved by the following safety regulatory organizations: UL IEC/EN/DIN EN 60747-5-5 Approved under UL 1577, component recognition program up to VISO=3750 VRMS CSA Approved under CSA Component Acceptance Notice #5. IEC/EN/DIN EN 60747-5-5 Insulation Characteristics* Description Symbol Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 150 Vrms for rated mains voltage ≤ 300 Vrms for rated mains voltage ≤ 600 Vrms Characteristic Unit I – IV I – III I – II Climatic Classification 40/125/21 Pollution Degree (DIN VDE 0110/1.89) 2 VIORM 567 Vpeak Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial discharge < 5 pC VPR 1063 Vpeak Input to Output Test Voltage, Method a* VIORM x 1.6 = VPR, Type and Sample Test, tm = 10 sec, Partial discharge < 5 pC VPR 907 Vpeak VIOTM 6000 Vpeak TS IS, INPUT PS, OUTPUT 175 150 600 °C mA mW RS >109  Maximum Working Insulation Voltage Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec) Safety-limiting values – maximum values allowed in the event of a failure. Case Temperature Input Current Output Power Insulation Resistance at TS, VIO = 500 V * 3 Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/EN/ DIN EN 60747-5-5) for a detailed description of Method a and Method b partial discharge test profiles. Insulation and Safety Related Specifications Parameter Symbol ACPL-M49U Units Conditions Minimum External Air Gap (Clearance) L(101) ≥5 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (Creepage) L(102) ≥5 mm Measured from input terminals to output terminals, shortest distance path along body. 0.08 mm Through insulation distance conductor to conductor, usually the straight line distance thickness between the emitter and detector. 175 V DIN IEC 112/VDE 0303 Part 1 Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) CTI Isolation Group (DIN VDE0109) IIIa Material Group (DIN VDE 0109) Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS -55 150 °C Operating Temperature TA -40 125 °C Temperature 260 °C Time 10 s Lead Soldering Cycle Note Average Forward Input Current IF(avg) 20 mA 1 Peak Forward Input Current (50% duty cycle, 1ms pulse width) IF(peak) 40 mA 2 Peak Transient Input Current ( 4800VRMS for 1 second. 8. This is in a 4-pin configuration where the VCC and VO pin are shorted together. 9. Common transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the rising edge of the common mode pulse, VCM, to assure that the ouput will remain in a Logic High state (i.e., Vo > 2.0V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM/dt on the falling edge of the common mode pulse signal, VCM to assure that the output will remain in a Logic Low state (i.e., Vo < 0.8V). 7 NORMALIZED CURRENT TRANSFER RATIO NORMALIZED CURRENT TRANSFER RATIO 1.2 TA = 25°C VCC = 5V VO = 0.5V 1 0.8 0.6 0.4 1 10 IF - INPUT CURRENT - mA 100 Figure 1. Normalized Current Transfer Ratio (IF = 4mA as reference) vs Input Current VCC = 5V, TA = 25°C 12 10 IF = 4mA 4 0 IF = 1mA 0.0 0.2 0.4 0.6 0.8 VOL - LOW LEVEL OUTPUT VOLTAGE - V 12 10 IF = 4mA 4 0 IF = 1mA 0.0 0.2 0.4 0.6 0.8 VOL - LOW LEVEL OUTPUT VOLTAGE - V Figure 5. Typical Low Level Output Current vs Output Voltage (4-Pin Configuration) 8 -50 -25 0 25 50 75 TA - TEMPERATURE - °C 100 125 TA = 25°C VCC = VO 20 IF = 20mA IF = 15mA 15 IF = 10mA 10 IF = 4mA 5 0 5 10 VO - OUTPUT VOLTAGE - V 15 IF = 20mA 8 2 0.6 VCC = 5V VO = 0.5V 100.00 IF = 10mA 6 0.7 Figure 4. Output Current vs Output Voltage (4-Pin Configuration) IF - FORWARD CURRENT - mA IOL - LOW LEVEL OUTPUT CURRENT - mA VCC = VO, TA = 25°C 0.8 0 1.0 Figure 3. Typical Low Level Output Current vs Output Voltage 14 0.9 25 8 2 IF = 4mA IF = 20mA IF = 10mA 6 IF = 10mA 1 Figure 2. Normalized Current Transfer Ratio (TA = 25°C as reference) vs Temperature IO - OUTPUT CURRENT - mA IOL - LOW LEVEL OUTPUT CURRENT - mA 14 1.1 1.0 10.00 IF + VF 1.00  0.10 0.01 1.2 1.3 1.4 1.5 VF - FORWARD VOLTAGE - V Figure 6. Typical Input Current vs Forward Voltage 1.6 1.E+00 VCC = VO = 15V ICEO - OFF-STATE CURRENT - μA IOH - LOGIC HIGH OUTPUT CURRENT - μA 1.E+00 1.E-01 1.E-02 1.E-03 1.E-04 25 50 75 100 TA - TEMPERATURE - °C Figure 7. Typical High Level Output Current vs Temperature 5V VO 1.5 V 2V IF IF MONITOR VOL 25 50 75 100 TA - TEMPERATURE - °C Figure 9. Switching Test Circuit +5 V RL IF 6 RL 1 6 1 5 3 4 Figure 10. Switching Test Circuit (4-pin configuration) VO C L = 15 pF VO 5 0.1 μF 3 4 tPLH tPHL 9 1.E-04 125 Figure 8. Typical Off-State Current vs Temperature (4-Pin Configuration) PULSE GEN. ZO = 50  tr = 5 ns 0 IF MONITOR 1.E-03 +5 V IF PULSE GEN. ZO = 50  tr = 5 ns 1.E-02 1.E-05 125 15V 12V 5V 3.3V 1.E-01 CL = 15 pF IF 1500 V VCM 0V 10% 90% 90% B 10% tr A tf VO 1 6 5V VO 0.1F 3 4 VOL SWITCH AT B: IF = 4 mA RL 5 VFF SWITCH AT A: IF = 0 mA VO VCC + VCM C L = 15 pF - PULSE GEN. Figure 11. Test Circuit for Transient Immunity and Typical Waveforms IF 1500 V VCM 0V 10% 90% tr VO 90% B 10% A tf 5V SWITCH AT B: IF = 4 mA 1 6 5 VFF SWITCH AT A: IF = 0 mA VO VCC 3 4 VOL + VCM - PULSE GEN. Figure 12. Test Circuit for Transient Immunity and Typical Waveforms (4-Pin Configuration) For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. AV02-3809EN - October 10, 2012 RL VO C L = 15 pF