ACPL-M61M-060E

Data Sheet ACPL-M61M 2.5V/3.3V Low-Power 10 MBd Digital Optocoupler Description Features The Broadcom ACPL-M61M is an optocoupler that combines a light emitting diode and an integrated high gain photo detector to address a low power supply need. It supports 2.5V/3.3V supply voltage with guaranteed AC and DC operational parameters at full industrial temperature range –40°C to +125°C. The optocoupler consumes low power across temperature with the LED driving current operating from as low as 1.6 mA.  The output of the detector IC is a CMOS output. The internal Faraday shield provides a guaranteed common mode transient immunity specification of 20 kV/μs. CAUTION! It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The components featured in this datasheet are not to be used in military or aerospace applications or environments. Broadcom        Supply voltage: 2.5V/3.3V Guaranteed AC and DC performance over wide industrial temperature: –40°C to +125°C Low supply current IDD: 1.5 mA max Low LED input driving current IF: 1.6 mA min Package: SO-5 High data rate: 10 MBd min Common Mode Rejection (CMR): 20 kV/μs minimum at VCM = 1000V Safety Approval: – UL 1577 - 3750 Vrms for 1 minute – CSA – IEC/EN/DIN EN 60747-5-5 for Reinforced Insulation Applications    Communication interface: RS485, CANBus ASIC system interface Digital isolation for A/D, D/A conversion ACPL-M61M-DS102 February 19, 2019 ACPL-M61M Data Sheet 2.5V/3.3V Low-Power 10 MBd Digital Optocoupler Functional Diagram Truth Table LED 6 VDD Anode 1 5 Cathode 3 Vo Output ON L OFF H NOTE: A 0.1-μF bypass capacitor must be connected as close as possible between pins VDD and GND. 4 GND Shield Ordering Information ACPL-M61M is UL Recognized with 3750 Vrms for 1 minute per UL1577. Option Part Number RoHS Compliant Package Surface Mount ACPL-M61M -000E SO-5 X Tape & Reel IEC/EN/DIN EN 60747-5-5 Quantity 100 per tube -060E X -500E X X X -560E X X 100 per tube 1500 per reel X 1500 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-M61M-560E to order product of Small Outline SO-5 package in Tape and Reel packaging with IEC/EN/DIN EN 607475-5 Safety Approval in RoHS compliant. Broadcom ACPL-M61M-DS102 2 ACPL-M61M Data Sheet 2.5V/3.3V Low-Power 10 MBd Digital Optocoupler Package Outline Drawing ACPL-M61M SO-5 Package LAND PATTERN RECOMMENDATION 0.33 (0.013) DEVICE PART NUMBER 4.4 ± 0.1 (0.173 ± 0.004) LEAD FREE NNNN Z • YYWW EEE 1.27 (0.05) 0.64 (0.025) TEST RATING CODE 7.0 ± 0.2 (0.276 ± 0.008) DATE CODE 4.39 (0.17) 8.26 (0.325) LOT ID PIN 1 DOT 1.80 (0.071) 0.4 ± 0.05 (0.016 ± 0.002) 2.54 (0.10) 3.6 ± 0.1* (0.142 ± 0.004) 2.5 ± 0.1 (0.098 ± 0.004) 0.102 ± 0.102 (0.004 ± 0.004) 1.27 BSC (0.050) 0.20 ± 0.025 (0.008 ± 0.001) 7° MAX. 0.71 MIN (0.028) Dimensions in millimeters (inches). Note: Foating Lead Protrusion is 0.15 mm (6 mils) max. * Maximum Mold flash on each side is 0.15 mm (0.006). MAX. LEAD COPLANARITY = 0.102 (0.004) Solder Reflow Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used. Regulatory Information    IEC/EN/DIN EN 60747-5-5 (Option 060E only) UL - Approval under UL 1577, component recognition program up to VISO = 3750 Vrms. CSA - Approval under CSA Component Acceptance Notice #5, File CA 88324. Broadcom ACPL-M61M-DS102 3 ACPL-M61M Data Sheet 2.5V/3.3V Low-Power 10 MBd Digital Optocoupler Insulation and Safety Related Specifications Parameter Symbol ACPL-M61M Unit Minimum External Air Gap (External Clearance) L(101) 5 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (External Creepage) L(102) 5 mm Measured from input terminals to output terminals, shortest distance path along body. 0.08 mm Through insulation distance conductor to conductor, usually the straight line distance thickness between the emitter and detector. 175 V Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) CTI Isolation Group IIIa Conditions DIN IEC 112/VDE 0303 Part 1. Material Group (DIN VDE 0110, 1/89, Table 1). IEC/EN/DIN EN 60747-5-5 Insulation Characteristics (Option 060E) Description Symbol Characteristic Unit Installation classification per DIN VDE 0110/39, Table 1 For Rated Mains Voltage ≤ 150 Vrms I – IV For Rated Mains Voltage ≤ 300 Vrms I – IV For Rated Mains Voltage ≤ 450 Vrms I – III Climatic Classification 55/125/21 Pollution Degree (DIN VDE 0110/39) 2 Maximum Working Insulation Voltage VIORM 567 VPEAK Input to Output Test Voltage, Method VIORM x 1.875 = VPR, 100% Production Test with tm=1 sec, Partial discharge < 5 pC VPR 1063 VPEAK Input to Output Test Voltage, Method aa VIORM x 1.6 = VPR, Type and Sample Test, tm=10 sec, Partial discharge < 5 pC VPR 907 VPEAK VIOTM 6000 VPEAK TS 150 °C Input Current IS, INPUT 150 mA Output Power PS, OUTPUT 600 mW RS >109 Ω ba Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec) Safety-Limiting Values – maximum values allowed in the event of a failure Case Temperature Insulation Resistance at TS, VIO = 500V a. Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/EN/DIN EN 60747-5-5) for detailed description of Method a and Method b partial discharge test profiles. NOTE: Broadcom These optocouplers are suitable for safe electrical isolation only within the safety limit data. Maintenance of the safety data shall be ensured by means of protective circuits. ACPL-M61M-DS102 4 ACPL-M61M Data Sheet 2.5V/3.3V Low-Power 10 MBd Digital Optocoupler Absolute Maximum Ratings Parameter Symbol Min Max Unit Storage Temperature TS –55 150 °C Operating Temperature TA –40 125 °C Reverse Input Voltage VR — 5 V Supply Voltage VDD — 4 V IF — 8 mA IF(TRAN) — 1 A — 80 mA 10 mA Average Forward Input Current Peak Forward Input Current Output Current IO Output Voltage VO –0.5 VDD + 0.4 V Input Power Dissipation PI — 14 mW Output Power Dissipation PO — 8 mW Lead Solder Temperature TLS — Solder Reflow Temperature Profile Condition ≤1 μs pulse width, ≤100 pulses per second ≤1 μs pulse width,