ACPL-M72T-000E

ACPL-M71T and ACPL-M72T High Speed, Low Power Digital Optocouplers with R2Coupler™ Isolation and AEC-Q100 Grade 1 Qualification Data Sheet Description Features The Avago ACPL-M71T and ACPL-M72T are high temperature, digital CMOS optocouplers in SOIC-5 packages. Suitable for hybrid and electric vehicle applications, the optocouplers use the latest CMOS IC technology to achieve outstanding performance and very low power consumption. All devices are AEC-Q100 compliant and operate over the –40°C to 125 °C temperature range. • 5 V CMOS compatible The ACPL-M71T uses a high speed LED, and the ACPL-M72T uses a low current LED for lower power dissipation. The high speed ACPL-M71T featuring a 35 ns maximum propagation delay (IF =10 mA). The ACPL-M72T optocoupler features very low power. With a low 4 mA LED drive current, ACPL-M72T typical propagation delay is 60 ns. Each digital optocoupler has a CMOS detector IC, an integrated photodiode, a high speed transimpedance amplifier, and a voltage comparator with an output driver. Avago R2Coupler isolation products provide the reinforced insulation and reliability needed for critical in automotive and high temperature industrial applications • Common-Mode Rejection 40kV/µs @ VCM=1000V: • Wide automotive temperature range: –40°C to 125°C • Low propagation delay : – High Speed ACPL-M71T: 26ns @ IF = 10 mA (Typical) – Low Power ACPL-M72T: 60ns @ IF = 4 mA (Typical) • Worldwide safety approval: – UL 1577 recognized, 4000 Vrms / 1 min – CSA approved – IEC/EN/DIN EN 60747-5-5 • Qualified to AEC-Q100 Grade 1 test guidelines Applications • Automotive CANBus communications interface • Automotive isolated high speed gate drivers for IGBTs and Power MOSFETs • High temperature digital signal isolation • Microcontroller interface • Digital isolation for A/D and D/A conversion Functional Block Diagram ACPL-M71T/ACPL-M72T 6 Vdd Anode 1 5 Vo Truth Table LED Output (VO) Cathode 3 4 Gnd OFF H ON L Note: A 0.1 µF bypass capacitor must be connected between pins 4 and 6. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Ordering Information Option Part Number (RoHS) Compliant Package Surface Mount ACPL-M71T -000E SO-5 X ACPL-M72T X -500E X X -560E X X SO-5 Quantity 100 per tube -060E -000E IEC/EN/DIN EN 60747-5-5 Tape & Reel X 100 per tube 1500 per reel X 1500 per reel X 100 per tube -060E X -500E X X X -560E X X 100 per tube 1500 per reel X 1500 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. For example, the part number ACPL-M71T-500E describes a device with a surface mount SOIC-5 package; delivered in Tape and Reel with 1500 parts per reel; and full RoHS compliance. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Package Dimensions ACPL-M71T / ACPL-M72T (JEDEC MO-155 Package) ANODE 1 M71T YWW EE 4.4 ± 0.1 (0.173 ± 0.004) 7.0 ± 0.2 (0.276 ± 0.008) CATHODE 3 0.4 ± 0.05 (0.016 ± 0.002) 6 V CC 5 V OUT 4 GND Extended Datecode for lot tracking 3.6 ± 0.1* (0.142 ± 0.004) 2.5 ± 0.1 (0.098 ± 0.004) 0.102 ± 0.102 (0.004 ± 0.004) 0.20 ± 0.025 (0.008 ± 0.001) 7° MAX. 1.27 BSC (0.050) DIMENSIONS IN MILLIMETERS (INCHES) * MAXIMUM MOLD FLASH ON EACH SIDE IS 0.15 mm (0.006) NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. 2 0.71 MIN (0.028) MAX. LEAD COPLANARITY = 0.102 (0.004) Land Pattern Recommendation 4.4 (0.17) 1.3 (0.05) 2.5 (0.10) 2.0 (0.080) 0.64 (0.025) 8.27 (0.325) DIMENSION IN MILLIMETERS (INCHES) Recommended Pb-Free IR Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Note: Non-halide flux should be used. Regulatory Information The ACPL-M71T and ACPL-M72T are approved by the following organizations: UL IEC/EN/DIN EN 60747-5-5 Approved under UL 1577, component recognition program up to VISO = 4000 VRMS. IEC 60747-5-5: EN 60747-5-5: DIN EN 60747-5-5: CSA Approved under CSA Component Acceptance Notice #5. 3 Insulation and Safety Related Specifications Parameter Symbol Value Units Conditions Minimum External Air Gap (Clearance) L(I01) >5 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (Creepage) L(I02) >5 mm Measured from input terminals to output terminals, shortest distance path along body. 0.08 mm Insulation thickness between emitter and detector; also known as distance through insulation. >175 V DIN IEC 112/VDE 0303 Part 1 Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) CTI Isolation Group IIIa Material Group (DIN VDE 0109) IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Description Symbol ACPL-M71T/ ACPL-M72T Units Maximum Working Insulation Voltage VIORM 567 VPEAK Input to Output Test Voltage, Method b† VPR 1063 VPEAK Input to Output Test Voltage, Method a† VIORM x 1.6 = VPR, Type and Sample Test, tm = 10 sec, Partial Discharge < 5 pC VPR 907 VPEAK Highest Allowable Overvoltage† (Transient Overvoltage, tini = 60 sec) VIOTM 6000 VPEAK Case Temperature Ts 150 °C Input Current Is, INPUT 150 mA Output Power Ps,OUTPUT 600 mW Insulation Resistance at TS, VIO = 500 V RIO ≥109 Ω VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC Safety Limiting Values (Maximum values allowed in the event of a failure, also see Thermal Derating curve, Figure 11.) 4 Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS –55 +130 °C Ambient Operating Temperature[1] TA –40 +125 °C Supply Voltages VDD 0 6.5 V Output Voltage VO –0.5 VDD +0.5 V Average Forward Input Current IF – 20.0 mA Peak Transient Input Current (IF at 1 µs pulse width,