ACPL-P481-500E

ACPL-P481 and ACPL-W481 Inverted Logic, High CMR Optocoupler for Intelligent Power Modules and IGBT/MOSFET Gate Drive Data Sheet Description Features The high-speed ACPL-P481/W481 optocoupler contains a GaAsP LED, a photo detector, and a Schmitt trigger that eliminates the requirement for external waveform conditioning circuits.  The totem pole output eliminates the requirement for a pull-up resistor. An Intelligent Power Module, Power MOSFET, or IGBT can be driven directly.  Propagation delay difference between devices has been minimized to maximize inverter efficiency through reduced switching dead time.        Applications      IPM Interface Isolation Isolated IGBT/MOSFET Gate Drive AC and Brushless DC Motor Drives Industrial Inverters General Digital Isolation Specifications Functional Diagram  Anode 1 6 VCC N.C. 2 5 VO   Cathode 3 SHIELD 4 Ground Note: A 0.1 μF bypass capacitor must be connected between pins 4 and 6.    V0 On LOW OFF HIGH Wide Operating Temperature Range: –40°C to 100°C Maximum Propagation Delay tPHL/tPLH = 350 ns Maximum Pulse Width Distortion (PWD) = 250 ns Propagation Delay Difference: Min. –100 ns, Max. 250 ns Wide Operating VCC Range: 4.5V to 20V 20 kV/μs Minimum Common Mode Rejection (CMR) at VCM = 1000V CAUTION Truth Table (Inverting Logic) LED Inverted output type (totem pole output) Performance Specified for Common IPM Applications Over Industrial Temperature Range Short Maximum Propagation Delays Minimized Pulse Width Distortion (PWD) Very High Common Mode Rejection (CMR) Hysteresis Available in Stretched SO-6 Package. Package Clearance/Creepage at 8 mm (ACPL-W481) Safety Approval: (pending) — UL Recognized with 3750VRMS (5000VRMS for ACPL-W481) for 1 minute per UL1577. — CSA Approved. — IEC/EN/DIN EN 60747-5-5 Approved with VIORM = 891Vpeak for ACPL-P481 and VIORM = 1140Vpeak for ACPL-W481, under option 060. Broadcom -1- It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. ACPL-P481 and ACPL-W481 Data Sheet Ordering Information ACPL-P481/W481 is UL recognized with 3750/5000VRMS for 1 minute respectively per UL 1577. Both are approved under CSA Component Acceptance Notice #5, File CA 88324. Option Part Number Package Surface Mount -000E X -500E Stretched SO-6 X Tape and Reel RoHS Compliant ACPL-P481 ACPL-W481 -060E IEC/EN/DIN EN 60747-5-5 100 per tube X X -560E X Quantity X 100 per tube X 100 per tube X 100 per tube To order, choose a part number from the part number column and combine with the desired option from the option column to form an ordering part number. Example 1: ACPL-P481-560E: Stretched SO-6 Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval and RoHS compliant. Example 2: ACPL-P481-000E: Stretched SO-6 Surface Mount package in tube packaging and RoHS compliant. Option data sheets are available. Contact your Broadcom sales representative or authorized distributor for information. Recommended Pb-Free IR Profile The recommended reflow profile is per JEDEC Standard, J-STD-020 (latest revision). Non-halide flux should be used. Regulatory Information The ACPL-P481/W481 is approved by the following organizations:    IEC/EN/DIN EN 60747-5-5 (Option 060 only): Approved with Maximum Working Insulation Voltage VIORM = 891Vpeak for ACPL-P481 and VIORM = 1140Vpeak for ACPL-W481. UL: Approval under UL 1577, component recognition program up to VISO = 3750VRMS (5000VRMS for ACPL-W481). File E55361. CSA: Approval under CSA Component Acceptance Notice #5, File CA 88324. Broadcom -2- ACPL-P481 and ACPL-W481 Data Sheet Package Outline Drawings ACPL-P481 Stretched SO-6 Package (7 mm Clearance) +0.254 0 +0.010 0.180 - 0.000 1.27 BSG 0.050 0.381 ±0.127 0.015 ±0.005 *4.580 1.27 0.050 7.62 0.300 6.81 0.268 0.45 0.018 10.7 0.421 1.590 ±0.127 0.063 ±0.005 45° 0.76 0.030 2.16 0.085 3.180 ±0.127 0.125 ±0.005 7° 7° 7° 7° 0.20 ±0.10 0.008 ±0.004 0.254 ±0.050 0.010 ±0.002 5 NOM. 1±0.250 0.040 ±0.010 9.7 ±0.250 0.382 ±0.010 Floating Lead protusion max. = 0.25 mm [0.01 inches] Lead Coplanarity = 0.1 mm [0.004 inches] Dimensions in millimeters [inches] *Total Package Width = 4.834 ±0.254 mm (inclusive of mold flash) ACPL-W481 Stretched SO-6 Package (8 mm Clearance) 0.381 ±0.127 0.015 ±0.005 1 12.650 0.498 0.760 0.030 6 2 5 3 4 7.62 [0.300] +0.127 6.807 -0.000 +0.005 0.268 - 0.000 0.45 0.018 +0.254 0 +0.010 0.180 - 0.000 *4.580 1.27 BSG 0.050 7° 45° 1.905 0.075 1.270 0.050 1.590 ±0.127 0.063 ±0.005 3.180 ±0.127 0.125 ±0.005 0.20 ±0.10 0.008 ±0.004 7° 0.750 ±0.250 [0.0295 ±0.010] 35° NOM. 11.500 ±0.25 0.453 ±0.010 0.254 ±0.050 0.010 ±0.002 Floating Lead protusion max. = 0.25 mm [0.01 inches] Lead Coplanarity = 0.1 mm [0.004 inches] Dimensions in millimeters [inches] *Total Package Width = 4.834 ±0.254 mm (inclusive of mold flash) Broadcom -3- 7° 7° ACPL-P481 and ACPL-W481 Data Sheet IEC/EN/DIN EN 60747-5-5 Insulation Characteristics (ACPL-P481/W481 Option 060) Description Symbol ACPL-P481 ACPL-W481 I– IV I – IV I – III I – IV I – IV I – IV 55/100/21 55/100/21 2 2 VIORM 891 1140 Vpeak VPR 1670 2137 Vpeak VPR 1426 1824 Vpeak VIOTM 6000 8000 Vpeak TS 175 175 °C Input Current IS, INPUT 230 230 mA Output Power PS, OUTPUT 600 600 mW RS >109 >109 Ω Installation Classification per DIN VDE 0110/39, Table 1 for rated mains voltage ≤ 150VRMS for rated mains voltage ≤ 300VRMS for rated mains voltage ≤ 600VRMS Climatic Classification Pollution Degree (DIN VDE 0110/39) Maximum Working Insulation Voltage Input to Output Test Voltage, Method ba Unit VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC Input to Output Test Voltage, Method aa VIORM x 1.6=VPR, Type and Sample Test, tm = 10 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec) Safety-limiting Values – maximum values allowed in the event of a failure Case Temperature Insulation Resistance at TS, VIO = 500V a. Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under the Product Safety Regulations section, (IEC/EN/DIN EN 60747-5-5), for a detailed description of Method a and Method b partial discharge test profiles. Insulation and Safety Related Specifications Parameter Symbol ACPL-P481 ACPL-W481 Unit Minimum External Air Gap (External Clearance) L(101) 7.0 8.0 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (External Creepage) L(102) 8.0 8.0 mm Measured from input terminals to output terminals, shortest distance path along body. 0.08 0.08 mm Through insulation distance conductor to conductor, usually the straight line distance thickness between the emitter and detector. >175 >175 V IIIa IIIa Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) Isolation Group CTI Broadcom -4- Condition DIN IEC 112/VDE 0303 Part 1. Material Group (DIN VDE 0110, 1/89, Table 1). ACPL-P481 and ACPL-W481 Data Sheet Absolute Maximum Ratings Parameter Symbol Min. Max. Unit Storage Temperature TS –55 +125 °C Operating Temperature TA –40 +100 °C Average Input Current IF(AVG) 10 mA Peak Transient Input Current (