ACPL-W480-000E

ACPL-P480 and ACPL-W480 High CMR Intelligent Power Module and Gate Drive Interface Optocoupler Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features The ACPL-P480 and ACPL-W480 fast speed optocouplers contain a GaAsP LED and photo detector with built-in Schmitt trigger to provide logic-compatible waveforms, eliminating the need for additional wave shaping. The totem pole output eliminates the need for a pull up resistor and allows for direct drive Intelligent Power Module or gate drive. Minimized propagation delay difference between devices make these optocouplers excellent solutions for improving inverter efficiency through reduced switching dead time. • Performance Specified for Common IPM Applications Over Industrial Temperature Range. • Short Maximum Propagation Delays • Minimized Pulse Width Distortion (PWD) • Very High Common Mode Rejection (CMR) • Hysteresis • Totem Pole Output (No Pull-up Resistor Required) • Available in Stretched SO-6 package. • Safety Approval: UL Recognized with 3750 Vrms for 1 minute (5000 Vrms for 1 minute for all ACPL-W480 devices and Option 020 device for ACPL-P480) per UL1577. CSA Approved. IEC/EN/DIN EN 60747-5-5 Approved: VIORM = 891 Vpeak for ACPL-P480, and VIORM = 1140 Vpeak for ACPL-W480. Functional Diagrams ACPL-P480 ANODE 1 6 VCC N.C. 2 5 VO CATHODE 3 SHIELD 4 Ground Specifications ACPL-W480 ANODE 1 6 VCC N.C. 2 5 VO CATHODE 3 SHIELD 4 Ground Note: A 0.1 µF bypass capacitor must be connected between pins 4 and 6. Truth Table (Positive Logic) LED VO ON HIGH OFF LOW • • • • • • Wide operating temperature range: –40°C to 100°C. Maximum propagation delay tPHL / tPLH = 350 ns Maximum Pulse Width Distortion (PWD) = 250 ns. Propagation Delay Difference: Min. –100 ns, Max. 250 ns Wide Operating VCC Range: 4.5 to 20 Volts 20 kV/µs minimum common mode rejection (CMR) at VCM = 1000 V. Applications • • • • • IPM Interface Isolation Isolated IGBT/MOSFET Gate Drive AC and Brushless DC Motor Drives Industrial Inverters General Digital Isolation CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Ordering Information ACPL-P480 is UL Recognized with 3750 Vrms for 1 minute and ACPL-W480 is UL Recognized with 5000 Vrms for 1 minute per UL1577. Both are approved under CSA Component Accep­tance Notice #5, File CA 88324. Option Part number RoHS Compliant Package -000E ACPL-P480 -520E X 7mm Stretched SO-6 X X -560E X -500E -060E -560E IEC/EN/DIN EN 60747-5-5 X X X 100 per reel X 1000 per reel X 100 per tube X 1000 per reel X X X X 1000 per reel X X X 8mm Stretched SO-6 Quantity 100 per tube X -060E -000E ACPL-W480 Tape & Reel UL 1577 5000VRMS / 1 Minute Rating X -500E -020E Surface Mount X 100 per tube X 1000 per reel X X 100 per tube X X 1000 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-P480-560E to order product of Stretched SO-6 package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: ACPL-P480-000E to order product of Stretched SO-6 package in tube packaging and RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. 2 Package Outline Drawings ACPL-P480 Stretched SO-6 Package, 7 mm clearance +0.254 0 +0.010 0.180 - 0.000 1.27 BSG 0.050 0.381 ±0.127 0.015 ±0.005 4.580 1.27 0.050 7.62 0.300 6.81 0.268 0.45 0.018 45° 10.7 0.421 1.590 ±0.127 0.063 ±0.005 0.76 0.030 2.16 0.085 3.180 ±0.127 0.125 ±0.005 7° 7° 7° 7° 0.20 ±0.10 0.008 ±0.004 0.254 ±0.050 0.010 ±0.002 5 NOM. 1±0.250 0.040 ±0.010 Floating Lead Protusions max. 0.25 [0.01] Dimensions in Millimeters [ Inches ] Lead Coplanarity= 0.1mm [0.004 Inches ] 9.7 ±0.250 0.382 ±0.010 ACPL-W480 Stretched SO-6 Package, 8 mm clearance 0.381 ±0.127 0.015 ±0.005 1 4 7.62 [0.300] +0.127 6.807 - 0.000 +0.005 0.268 - 0.000 7° 45° 7° 35° NOM. 11.500 ±0.25 0.453 ±0.010 1.905 0.075 1.270 0.050 1.590 ±0.127 0.063 ±0.005 0.20 ±0.10 0.008 ±0.004 3 0.760 0.030 5 3 0.750 ±0.250 [0.0295 ±0.010] 12.650 0.498 6 2 0.45 0.018 +0.254 0 +0.010 0.180 - 0.000 4.580 1.27 BSG 0.050 0.254 ±0.050 0.010 ±0.002 3.180 ±0.127 0.125 ±0.005 7° 7° Floating Lead protusion max. 0.25[0.01] Dimensions in millimeters [inches] Lead Coplanarity=0.1 mm [0.004 inches] Solder Reflow Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used. Regulatory Information The ACPL-P480 and ACPL-W480 are approved by the following organizations: IEC/EN/DIN EN 60747-5-5 (Option 60 only) UL Approval under: IEC 60747-5-5 : 2007 EN 60747-5-5 : 2011 DIN EN 60747-5-5 (VDE 0884-5) : 2011-11 ACPL-P480: Approval under UL 1577, component recognition program up to VISO = 3750 VRMS. File E55361. CSA Approval under CSA Component Acceptance Notice #5, File CA 88324. ACPL-W480 and ACPL-P480 (option 020): Approval under UL 1577, component recognition program up to VISO = 5000 VRMS. File E55361. Table 1. IEC/EN/DIN EN 60747-5-5 Insulation Characteristics* (Option 060) Characteristic Description Symbol Installation classification per DIN VDE 0110/39, Table 1 for rated mains voltage ≤ 300 Vrms for rated mains voltage ≤ 450 Vrms for rated mains voltage ≤ 600 Vrms ACPL-P480 ACPL-W480 I - IV I - III I - III I - IV I - IV I - IV Climatic Classification 55/100/21 Pollution Degree (DIN VDE 0110/39) Maximum Working Insulation Voltage Unit 2 VIORM 891 1140 Vpeak Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial discharge < 5 pC VPR 1670 2137 Vpeak Input to Output Test Voltage, Method a* VIORM x 1.6 = VPR, Type and Sample Test with tm = 10 sec, Partial discharge < 5 pC VPR 1426 1824 Vpeak VIOTM 6000 8000 Vpeak Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec) Safety-limiting values - maximum values allowed in the event of a failure. Case Temperature Input Current Output Power Insulation Pesistance at TS, VIO = 500 V TS IS,INPUT PS,OUTPUT 175 230 600 °C mA mW RS >109 W * Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/EN/ DIN EN 60747-5-5) for a detailed description of Method a and Method b partial discharge test profiles. 4 Table 2. Insulation and Safety Related Specifications Parameter Symbol ACPL-P480 ACPL-W480 Units Conditions Minimum External Air Gap (External Clearance) L(101) 7.0 8.0 mm Measured from input terminals to output terminals shortest distance through air. Minimum External Tracking (External Creepage) L(102) 8.0 8.0 mm Measured from input terminals to output terminals shortest distance path along body. Minimum Internal Plastic Gap (Internal Clearance) 0.08 mm Through insulation distance conductor to conductor, usually the straight line distance thickness between the emitter and detector. Minimum Internal Tracking (Internal Creepage) NA mm Measured from input terminals to output tereminals, along internal cavity. >175 V Tracking Resistance (Comparative Tracking Index) CTI Isolation Group IIIa DIN IEC 112/VDE 0303 Part 1 Material Group (DIN VDE 0110, 1/89, Table 1) Table 3. Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS -55 125 °C Operating Temperature TA -40 100 °C Average Input Current IF(avg) 10 mA Peak Transient Input Current (