ACPM-7355-BLK

ACPM-7355 UMTS Dual-Band 4x5mm Power Amplifier Module (Band2/Band5) Data Sheet Description Features The ACPM-7355 is a dual-band PAM (Power Amplifier Module) designed for UMTS Band2 and Band5. The ACPM7355 meets stringent UMTS linearity requirements. The 4mmx5mm form factor 14-pin surface mount package is self contained, incorporating 50ohm input and output matching networks x Dual-Band PA (Band2 and Band5) 5th x Small Size (4x5mm) x Thin Package (1.0mm typ) x Excellent Linearity x 3-mode power control The ACPM-7355 features generation of CoolPAM circuit technology which supports 3 modes – bypass, mid and high power modes. The CoolPAM is stage bypass technology which enables power amplifier to lower power consumption. Active bypass feature is added to 5th generation to enhance power added efficiency at low output range and this technology extends talk time of mobiles more by further saving power amplifier’s current consumption. x Bypass / Mid Power Mode / High Power Mode High Efficiency at max output power The power amplifier is manufactured on an advanced InGaP HBT (hetero-junction Bipolar Transistor) MMIC (microwave monolithic integrated circuit) technology offering state-of-the-art reliability, temperature stability and ruggedness. x UMTS Band2 and Band5 The Module is housed in a cost effective, small and thin 4x5mm package. x 14-pin surface mounting package x Internal 50ohm matching networks for both RF input and output x Lead-free, RoHS compliant, Green Applications Ordering Information Part Number RFin_LB 1000 178mm (7”) Tape/Reel ACPM-7355-BLK 100 Bulk Vcc1 Ven_LB Ven_HB RFin_HB Impedance Transformer Input Match & Power Divider Output Match Output Match Bypass Circuit Impedance Transformer RFout_LB Vcc2 Vmode Vbp Bias Circuit & Control Logic Input Match & Power Divider Container ACPM-7355-TR1 Block Diagram Bypass Circuit Number of Devices RFout_HB Absolute Maximum Ratings No damage assuming only one parameter is set at limit at a time with all other parameters set at or below typical value. Operation of any single parameter outside these conditions with the remaining parameters set at or below typical values may result in permanent damage. Description Min RF Input Power (high power mode) Output power (bypass mode) Output power (mid power mode) Typ Max Unit Associated Pins 0 10 10 18 dBm RFIn_Hi, RFIn_Low RFOut_Hi, RFOut_Low RFOut_Hi, RFOut_Low DC Supply Voltage 0 3.4 5.0 V Vcc1, Vcc2 Enable Voltage 0 2.6 3.3 V Ven_Low, Ven_Hi Mode Control Voltage 0 2.6 3.3 V Vmode Bypass Control 0 2.6 3.3 V Vbp Storage Temperature -55 25 +125 °C Recommended Operating Condition Description Min Typ Max Unit DC Supply Voltage 3.2 3.4 4.2 V LOW HIGH 0 1.35 0 2.6 0.5 3.1 V V LOW HIGH 0 1.35 0 2.6 0.5 3.1 V V LOW HIGH 0 1.35 0 2.6 0.5 3.1 V V 849 1910 MHz MHz 85 °C Enable Voltage (Ven_Low, Ven_Hi) Mode Control Voltage (Vmode) Bypass Control Voltage (Vbp) Operating Frequency Band5 Band2 824 1850 Ambient Temperature -30 25 Operating Logic Table Power Mode Ven_Low, Ven_Hi Vbp Vmode Pout (Rel99) Pout (HSDPA, HSUPA MPR=0dB) High Power Mode HIGH LOW LOW ~27.0dBm (Band5) ~27.5dBm(Band2) ~26.0dBm (Band5) ~ 26.5dBm (Band2) Mid Power Mode HIGH LOW HIGH ~17dBm ~16dBm Bypass Mode HIGH HIGH HIGH ~8dBm ~7dBm Shut Down Mode LOW LOW LOW – – 2 Electrical Characteristics in Band5 – Conditions: Vcc = 3.4V, Ven_Low = 2.6V, T = 25°C, Zin/Zout = 50ohm – Signal Configuration: 3GPP (DPCCH+1DPDCH) Up-Link unless specified otherwise Characteristics Condition Operating Frequency Range Gain High Power Mode, Pout=27dBm Total Supply Current Min Typ Max Unit 824 – 849 MHz 24 28.5 Mid Power Mode, Pout=17dBm 15 19.5 dB Bypass Power Mode, Pout=8dBm 10 15 dB High Power Mode, Pout=27dBm Quiescent Current dB 380 440 mA Mid Power Mode, Pout=17dBm 70 100 mA Bypass Power Mode, Pout=8dBm 13.5 20 mA High Power Mode 70 95 120 mA Mid Power Mode 10 20 30 mA Bypass Mode 2 3.4 5 mA High Power Mode 10 PA Mid Power Mode 10 PA Bypass Mode 10 PA Mid Power Mode 5 PA Bypass Mode 5 PA 100 PA Total Current in Power-down mode Ven_Low=0V, Vmode=0V, Vbp=0V 0.2 5 PA Adjacent Channel Leakage Ratio 5 MHz offset 10 MHz offset High Power Mode, Pout=27dBm -42 -55 -36 -46 dBc dBc 5 MHz offset 10 MHz offset High Power Mode, Pout=26dBm (HSDPA, HSUPA MPR=0dB) -40 -51 -35 -46 dBc dBc 5 MHz offset 10 MHz offset Mid Power Mode, Pout=17dBm -49 -61 -36 -46 dBc dBc 5 MHz offset 10 MHz offset Mid Power Mode, Pout=16dBm (HSDPA, HSUPA MPR=0dB) -47 -59 -36 -46 dBc dBc 5 MHz offset 10 MHz offset Bypass Mode, Pout=8dBm -41 -58 -36 -46 dBc dBc 5 MHz offset 10 MHz offset Bypass Mode, Pout=7dBm (HSDPA, HSUPA MPR=0dB) -40 -58 -36 -46 dBc dBc Second Third High Power Mode, Pout=27dBm -37 -72 -30 -40 dBc dBc Enable Current Mode Control Current Bypass Control Current Harmonic Suppression Input VSWR Stability (Spurious Output) 2:1 In-Band Load VSWR