ALM-80110-BLKG

ALM-80110 0.25W Analog Variable Gain Amplifier Data Sheet Description Features Avago Technologies ALM-80110 is a 0.25W Analog Controlled Variable Gain Amplifier which operates from 0.4GHz to 1.6GHz. The device provides an exceptionally high OIP3 level of 40dBm, which is maintained over a wide attenuation range. The device features wide gain control range, low current, excellent input and output return loss. • Halogen free The ALM-80110 is housed in a miniature 5.0X5.0X1.1 mm3, 10-lead multiple-chips-on-board (MCOB) module package. This part is suitable for the AGC/Temperature compensation circuits application in wireless infrastructure such as Cellular/PCS/W-CDMA/WLLand and new generation wireless technologies systems. Pin connections and Package Marking • Wide Gain Control Range • High OIP3 across attenuation range Specifications At 0.9GHz, Vdd = 5V, Itotal = 110mA (typ), Vbias = 4V, Vctrl = 5V @ 25°C • OIP3 = 40.5dBm • Noise Figure = 4.8dB • Gain = 13.5dB • P1dB = 23.2dBm • IRL = 17dB, ORL = 12dB • Attenuation Range = 40dB Application • WLL, WLAN and other applications in the 400MHz to 1.6GHz range. 80110 WWYY XXXX • Transmitter and Receiver Gain Control Attention: Observe precautions for handling electrostatic sensitive devices. ESD Machine Model = 100 V ESD Human Body Model = 650 V Refer to Avago Application Note A004R: Electrostatic Discharge, Damage and Control. 10 Not used 9 EXT Lout 8 GND 7 Vctrl • Temperature Compensation Circuitry 6 RFout Vdd RFin 1 C Not used 2 Vbias 3 GND 4 GND 5 C Note : Top View : Package marking provides orienation and identification “80110” = Device Code “WWYY“ = Workweek and Year Code  “XXXX” = Assembly Lot number L C RFin C C C Vctrl RFout Vbias Figure 1. Simplified Schematic diagram ALM-80110 Absolute Maximum Rating (1) TC = 25°C Thermal Resistance (2,3) Symbol Parameter Units Absolute Maximum Id,max Drain Current mA 140 Vd.,max Drain Voltage, RF output to ground V 5.5 Vctrl_max Control Voltage V 7 Vbias_max Biasing Voltage V 15 Pd Power Dissipation mW 770 Pin CW RF Input Power [4 dBm 26 Tj Junction Temperature °C 150 TSTG Storage Temperature °C -65 to 150 (Vd = 5.0V) θjc = 77.2°C/W Notes: 1. Operation of this device in excess of any of these limits may cause permanent damage 2. Derate 12.95mW/°C for TL > 86°C 3. Thermal resistance measured using 150°C Infra-Red Microscopy Technique. 4. Max rating for Pin is under Maximum Attenuation mode i.e. Vctrl = 1V. ALM-80110 Electrical Specification (1) TC = 25°C, Zo = 50Ω, Vdd = 5.0V, Vbias = 4.0V, Vctrl = 5.0V unless noted Symbol Parameter and Test Condition Frequency Units Min. Typ. Max. stdev Itotal Total Operating Current Range N/A mA 89 110 134 0.002 NF Noise Figure at minimal Attenuation 0.45GHz 0.7GHz 0.9GHz dB 5.5 4.7 4.8 5.4 0.090 0.45GHz 0.7GHz 0.9GHz dB 12 17 15 13.5 15 0.165 0.45GHz 0.7GHz 0.9GHz dBm 36 40 40 40.5 0.717 0.45GHz 0.7GHz 0.9GHz dBm 22 23.5 23.3 23.2 0.068 Gain OIP3(2) P1dB Gain at minimal Attenuation Output Third Order Intercept Point Output Power at 1dB Gain Compression IRL Input Return Loss 0.45GHz 0.7GHz 0.9GHz dB 12 20 17 NA ORL Output Return Loss 0.45GHz 0.7GHz 0.9GHz dB 10 10.5 12 NA ISO Isolation 0.45GHz 0.7GHz 0.9GHz dB 30.5 30.5 30.5 NA Vbias Attenuator Bias Voltage N/A V 2.7 4 5 NA Vctrl Gain Variation Control Voltage N/A V 1 – 5 NA ∆ Gain Gain Variation Range (from Vctrl=1V to 5V) 0.45GHz 0.7GHz 0.9GHz dB 46 43 40 NA Note : 1. Measurements obtained from a test circuit described in Figure 53. 2. OIP3 test condition: F1 – F2 = 10MHz, with input power of -10dBm per tone measured at worst case side band. 3. Standard deviation data are based on at least 1000 pieces samples size taken from 2 wafer lots. Future wafers allocated to this product may have nominal values anywhere between the upper and lower specification limits. 2 ALM-80110 Product Consistency Distribution at 900MHz TC = 25°C, Vdd = 5.0V, Vbias = 4.0V LSL USL USL CPK=3 .09 .10 .11 .12 CPK=2.3 .13 Figure 2. Itotal at 900MHz 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 Figure 3. NF at 900MHz LSL LSL USL CPK=3 12 13 CPK=2.2 14 15 Figure 4. Gain at 900MHz 3 36 37 38 39 40 41 42 43 44 45 46 Note : 1. Statistics distribution determined from a sample size of 1000 parts taken from 2 different wafers. 2. Future wafers allocation to this product may have typical values anywhere between the minimum and maximum specification limits. 3. Measurements are made on production testboard, which represents a trade-off between optimal OIP3, P1dB and NF. Circuit losses have been de-embedded from actual measurements. CPK=6 Figure 6. P1dB at 900MHz 35 Figure 5. OIP3 at 900MHz LSL 22 5.4 23 24 ALM-80110 Application Circuit Data for 450MHz TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 50 45 P1dB (dBm) OIP3 (dBm) 40 35 30 25 85°C 25°C -40°C 20 15 1.0 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 20 15 10 5 0 -5 -10 -15 -20 -25 -30 -35 1.0 85°C 25°C -40°C 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 85°C 25°C -40°C 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 Figure 11. ORL vs Control Voltage and Temperature at 450MHz 4 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 1.0 85°C 25°C -40°C 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 Figure 10. IRL vs Control Voltage and Temperature at 450MHz Isolation (dB) ORL (dB) Figure 9. Gain vs Control Voltage and Temperature at 450MHz -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 1.0 85°C 25°C -40°C Figure 8. P1dB vs Control Voltage and Temperature at 450MHz IRL (dB) Gain (dB) Figure 7. OIP3 vs Control Voltage and Temperature at 450MHz 25.0 24.0 23.0 22.0 21.0 20.0 19.0 18.0 17.0 16.0 15.0 1.0 4.5 5.0 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 -85 1.0 85°C 25°C -40°C 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 Figure 12. Isolation vs Control Voltage and Temperature at 450MHz 5.0 ALM-80110 Application Circuit Data for 450MHz (cont'd) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 50 45 P1dB (dBm) OIP3 (dBm) 40 35 30 25 85°C 25°C -40°C 20 15 0 10 20 30 Attenuation (dB) 40 50 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 85°C 25°C -40°C 0 10 20 30 Attenuation (dB) 40 50 10 20 30 Attenuation (dB) 40 50 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 85°C 25°C -40°C 0 10 20 30 Attenuation (dB) 40 50 50 85°C 25°C -40°C 85°C 25°C -40°C 48 46 44 42 40 38 36 0 10 20 30 Attenuation (dB) 40 Figure 17. Isolation vs Attenuation and Temperature at 450MHz 5 0 Figure 16. IRL vs Attenuation and Temperature at 450MHz OIP3 (dBm) Isolation (dB) Figure 15. ORL vs Attenuation and Temperature at 450MHz -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 -85 85°C 25°C -40°C Figure 14. P1dB vs Attenuation and Temperature at 450MHz IRL (dB) ORL (dB) Figure 13. OIP3 vs Attenuation and Temperature at 450MHz 26 25 24 23 22 21 20 19 18 17 16 50 34 150 250 350 450 550 Frequency (MHz) 650 Figure 18. OIP3 vs Frequency and Temperature at Vctrl = 5V 750 ALM-80110 Application Circuit Data for 450MHz (cont'd) 24.6 24.4 24.2 24.0 23.8 23.6 23.4 23.2 23.0 22.8 22.6 22.4 22.2 150 85°C 25°C -40°C Gain (dB) P1dB (dBm) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 250 350 450 550 Frequency (MHz) 650 750 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 150 85°C 25°C -40°C 250 350 450 550 Frequency (MHz) 85°C 25°C -40°C 250 350 450 550 Frequency (MHz) 650 750 Figure 20. Gain vs Frequency and Temperature at Vctrl = 5V ORL (dB) IRL (dB) Figure 19. P1dB vs Frequency and Temperature at Vctrl = 5V 19 18 17 16 15 14 13 12 11 10 9 150 650 750 Figure 21. IRL vs Frequency and Temperature at Vctrl = 5V 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 150 85°C 25°C -40°C 250 350 450 550 Frequency (MHz) 650 750 650 750 Figure 22. ORL vs Frequency and Temperature at Vctrl = 5V -28 30 Vctrl=5V Vctrl=4V 20 -30 Gain (dB) Isolation (dB) 10 -32 -34 -36 -40 150 250 350 450 550 Frequency (MHz) 650 Figure 23. Isolation vs Frequency and Temperature at Vctrl = 5V 6 Vctrl=3V Vctrl=2V -10 -20 Vctrl=1.5V -30 85°C 25°C -40°C -38 0 -40 750 -50 150 Vctrl=1V 250 350 450 550 Frequency (MHz) Figure 24. Gain vs Frequency and Control Voltage ALM-80110 Application Circuit Data for 450MHz (cont'd) 14 13 12 11 10 9 8 7 6 5 4 3 150 120 85°C 25°C -40°C 110 105 100 95 90 85 250 350 450 550 Frequency (MHz) 650 80 750 Figure 25. Noise Figure vs Frequency and Temperature at Vctrl = 5V 1.0 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 14 12 Ictrl (mA) 2.0 1.5 1.0 10 8 6 4 0.5 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 Figure 27. Current (Ibias) vs Control Voltage and Temperature 150 100 50 0 -50 -100 85°C 25°C -40°C -150 0 10 20 30 Attenuation (dB) 40 Figure 29. Phase vs Attenuation and Temperature at 450MHz (without external L1 as shown in Figure 54.) 0 1.0 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 Figure 28. Current (Ictrl) vs Control Voltage and Temperature 200 Phase (Degree) 85°C 25°C -40°C 2 0.0 1.0 7 5.0 16 85°C 25°C -40°C 2.5 -200 4.5 Figure 26. Current (Idd) vs Control Voltage and Temperature 3.0 Ibias (mA) 85°C 25°C -40°C 115 Idd (mA) NF (dB) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 50 4.5 5.0 ALM-80110 Application Circuit Data for 900MHz TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 44 42 38 P1dB (dBm) OIP3 (dBm) 40 36 34 32 85°C 25°C -40°C 30 28 26 1.0 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 20 15 10 5 0 -5 -10 -15 -20 -25 -30 -35 1.0 85°C 25°C -40°C 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 Figure 32. Gain vs Control Voltage and Temperature at 900MHz -10 -11 Isolation (dB) ORL (dB) -12 -13 -14 -15 85°C 25°C -40°C -17 -18 1.0 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 Figure 34. ORL vs Control Voltage and Temperature at 900MHz 8 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 1.0 85°C 25°C -40°C 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 Figure 33. IRL vs Control Voltage and Temperature at 900MHz -9 -16 85°C 25°C -40°C Figure 31. P1dB vs Control Voltage and Temperature at 900MHz IRL (dB) Gain (dB) Figure 30. OIP3 vs Control Voltage and Temperature at 900MHz 25 24 23 22 21 20 19 18 17 16 15 1.0 4.5 5.0 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 85°C 25°C -40°C 1.0 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 Figure 35. Isolation vs Control Voltage and Temperature at 900MHz 5.0 ALM-80110 Application Circuit Data for 900MHz (cont'd) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 44 85°C 25°C -40°C 42 40 P1dB (dBm) OIP3 (dBm) 38 36 34 32 30 28 26 0 10 20 30 Attenuation (dB) 40 50 Figure 36. OIP3 vs Attenuation and Temperature at 900MHz -9 -11 -13 IRL (dB) ORL (dB) -12 -14 -15 85°C 25°C -40°C -17 -18 0 10 20 30 Attenuation (dB) 40 50 10 20 30 Attenuation (dB) 40 50 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 85°C 25°C -40°C 0 10 20 30 Attenuation (dB) 40 50 48 85°C 25°C -40°C 85°C 25°C -40°C 46 44 42 40 38 0 10 20 30 Attenuation (dB) 40 Figure 40. Isolation vs Attenuation and Temperature at 900MHz 9 0 Figure 39. IRL vs Attenuation and Temperature at 900MHz OIP3 (dBm) Isolation (dB) Figure 38. ORL vs Attenuation and Temperature at 900MHz -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 85°C 25°C -40°C Figure 37. P1dB vs Attenuation and Temperature at 900MHz -10 -16 25 24 23 22 21 20 19 18 17 16 15 50 36 600 700 800 900 1000 Frequency (MHz) 1100 Figure 41. OIP3 vs Frequency and Temperature at Vctrl = 5V 1200 ALM-80110 Application Circuit Data for 900MHz (cont'd) 24.6 24.4 24.2 24.0 23.8 23.6 23.4 23.2 23.0 22.8 22.6 600 85°C 25°C -40°C Gain (dB) P1dB (dBm) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 700 800 900 1000 Frequency (MHz) 1100 1200 Figure 42. P1dB vs Frequency and Temperature at Vctrl = 5V -12 -6 -14 -8 ORL (dB) IRL (dB) -20 -22 -24 900 1000 Frequency (MHz) 1100 700 800 900 1000 Frequency (MHz) 1100 85°C 25°C -40°C Gain (dB) -30.0 -30.5 -31.0 85°C 25°C -40°C 800 900 1000 Frequency (MHz) -14 700 800 900 1000 Frequency (MHz) 1100 1200 Figure 45. ORL vs Frequency and Temperature at Vctrl = 5V -29.5 700 -12 -20 600 1200 -29.0 -31.5 1200 -18 Figure 44. IRL vs Frequency and Temperature at Vctrl = 5V Isolation (dB) 800 -16 85°C 25°C -40°C -26 -32.0 600 700 -10 -18 -28 600 85°C 25°C -40°C Figure 43. Gain vs Frequency and Temperature at Vctrl = 5V -16 1100 Figure 46. Isolation vs Frequency and Temperature at Vctrl = 5V 10 19 18 17 16 15 14 13 12 11 10 9 600 1200 25 20 15 10 5 0 -5 -10 -15 -20 -25 -30 600 Vctrl=4V Vctrl=5V Vctrl=3V Vctrl=2V Vctrl=1.5V Vctrl=1V 700 800 900 1000 Frequency (MHz) Figure 47. Gain vs Frequency and Control Voltage 1100 1200 ALM-80110 Application Circuit Data for 900MHz (cont'd) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 7 120 85°C 25°C -40°C 6.5 110 5.5 Idd (mA) NF (dB) 6 5 4.5 105 100 95 4 90 3.5 85 3 600 700 85°C 25°C -40°C 115 800 900 1000 Frequency (MHz) 1100 80 1200 Figure 48. Noise Figure vs Frequency and Temperature at Vctrl = 5V 1.0 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 Figure 49. Current (Idd) vs Control Voltage and Temperature 3.0 16 14 2.5 12 Ictrl (mA) Ibias (mA) 2.0 1.5 1.0 0.0 1.0 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 85°C 25°C -40°C Phase (Degree) 80 60 40 20 0 0 10 20 30 Attenuation (dB) 40 Figure 52. Phase vs Attenuation and Temperature at 900MHz (without external L1 as shown in Figure 54.) 11 85°C 25°C -40°C 0 1.0 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 Figure 51. Current (Ictrl) vs Control Voltage and Temperature 140 100 6 2 Figure 50. Current (Ibias) vs Control Voltage and Temperature 120 8 4 85°C 25°C -40°C 0.5 10 50 4.5 5.0 Application Circuit Description and Layout C5 L1 IN C2 C1 VBIAS L1 C6 VDD Anggerik 5x5 A2 Rev2 VCTL GND C1 GND C2 C7 C5 C6 C7 L4 L4 OUT C3 C3 Figure 53. Demoboard schematic and layout Bill of Materials ALM-80110 is a input fully matched and output prematched product. The product requires 3 biasing points i.e. Vdd (to bias up the PA), Vbias and Vctrl (for controlling the attenuator circuitry). The Vdd is connected to the output pin thru a RF choke, L4 (which isolates the inband signal from the DC supply). The bypass capacitor (C5, C6 and C7) helps to eliminate out of band low frequency signals. DC blocking capacitors (C2 and C3) are required for its input and output, to isolate the supply voltage from succeeding circuits. To improve input return loss, C1 is being use for external tuning. Description Circuit Symbol Size For 0.45GHz and 0.9GHz C1 0402 0.5pF Murata C2 0402 2.2nF Murata C3 0402 100pF Murata C5 0603 2.2uF Murata C6 0402 0.1uF Murata C7 0402 10pF Murata L1 0402 NA L4 0402 100nH Toko Note : NA – not being used on Demoboard 140 120 Phase (Degree) The external Inductor (L1), helps to stablize the attenuator performance (by gain flatness and change of phase) for the frequency of interest as well as improving its dynamic range. L1=82nH L1=Open 100 ALM-80110’s gain is adjusted by supplying a voltage thru Vctrl. For absolute dynamic range, Vctrl can operate from 0.8 to 5V, but for best linearity, Vctrl above 1V is recommended. 80 60 40 20 0 10 20 30 Attenuation (dB) 40 50 Figure 54. Phase vs Attenuation with and without External L1 at 900MHz 12 ALM-80110 Typical Scatter Parameters Tc = 25°C, Vdd = 5.0V, Vctrl = 5V, Vbias = 4.0V, Zo = 50Ω Freq GHz S11 Mag. Ang. dB S21 Mag. S21 Ang. S21 dB S12 Mag. S12 Ang. S12 dB S22 Mag. S22 Ang. S22 dB 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.5 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0 0.8 0.7 0.5 0.3 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.2 0.2 0.2 0.2 0.2 0.2 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.2 0.5 0.8 0.7 0.5 0.7 0.9 0.8 0.8 0.7 0.7 0.6 0.5 0.3 0.1 0.3 0.4 151.0 124.0 95.3 67.6 37.7 -3.2 -57.9 -94.0 -112.5 -121.7 -126.6 -131.6 -135.0 -136.9 -137.6 -136.7 -135.4 -133.3 -131.0 -129.3 -128.2 -128.2 -129.8 -132.4 -136.0 -140.5 -145.7 -151.1 -156.8 -162.5 173.8 -172.0 -123.0 -147.4 -176.3 177.9 175.9 153.8 148.6 138.3 112.0 91.4 83.0 76.2 60.5 39.6 105.9 96.1 -1.9 -3.1 -5.5 -9.2 -14.1 -19.4 -21.4 -19.7 -18.2 -17.2 -16.6 -16.5 -16.5 -16.6 -16.7 -16.9 -16.9 -16.7 -16.4 -15.9 -15.2 -14.4 -13.5 -12.7 -11.9 -11.1 -10.5 -10.0 -9.7 -9.4 -10.6 -16.2 -5.3 -1.9 -2.8 -5.9 -2.9 -0.6 -1.6 -2.0 -2.9 -3.3 -4.0 -6.0 -9.7 -21.9 -11.0 -8.6 2.0 4.9 6.7 7.3 7.0 6.5 5.9 5.4 5.0 4.6 4.3 4.1 3.9 3.7 3.6 3.4 3.3 3.2 3.2 3.1 3.0 3.0 2.9 2.8 2.8 2.7 2.6 2.5 2.4 2.3 1.7 1.2 0.5 0.2 0.1 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 -68.8 -118.0 -155.3 174.5 150.8 132.3 117.3 104.9 94.0 84.5 75.7 67.4 59.4 51.7 44.2 36.7 29.2 21.7 14.0 6.2 -1.9 -10.1 -18.5 -27.2 -36.1 -45.2 -54.5 -63.7 -73.0 -82.2 -125.7 -165.7 114.0 90.6 -12.0 -140.0 35.3 -20.0 -125.1 39.9 81.5 47.9 -17.1 -57.9 -26.8 -40.9 -64.2 -97.8 5.9 13.7 16.5 17.2 17.0 16.3 15.5 14.7 14.0 13.3 12.7 12.2 11.8 11.4 11.0 10.7 10.4 10.2 10.0 9.8 9.6 9.5 9.3 9.1 8.9 8.6 8.3 8.0 7.6 7.1 4.4 1.4 -5.3 -13.5 -22.8 -30.3 -37.7 -53.1 -59.4 -67.3 -60.5 -55.4 -52.2 -58.1 -59.1 -53.3 -52.7 -44.9 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 131.5 92.5 63.7 42.6 27.2 16.2 8.1 1.9 -3.2 -7.7 -12.2 -16.2 -20.4 -24.5 -28.7 -33.0 -37.7 -42.5 -47.5 -52.9 -58.6 -65.0 -71.3 -77.9 -85.2 -92.5 -100.0 -107.8 -115.6 -123.5 -161.4 162.5 80.7 9.5 -128.9 170.4 70.0 39.1 156.5 115.5 96.7 55.3 -11.3 -51.3 -50.3 -44.5 -62.5 -97.7 -43.6 -35.6 -32.3 -30.9 -30.5 -30.3 -30.4 -30.3 -30.3 -30.2 -30.0 -29.9 -29.6 -29.4 -29.1 -28.8 -28.5 -28.2 -27.9 -27.6 -27.3 -27.0 -26.8 -26.6 -26.4 -26.3 -26.2 -26.2 -26.3 -26.4 -27.9 -30.1 -36.5 -45.2 -45.5 -38.1 -43.7 -66.8 -51.8 -56.7 -52.9 -51.5 -50.4 -55.0 -58.5 -55.4 -53.7 -45.3 0.4 0.1 0.2 0.3 0.3 0.3 0.3 0.3 0.2 0.2 0.2 0.2 0.2 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.2 0.2 0.2 0.3 0.3 0.3 0.4 0.4 0.5 0.5 0.5 0.5 0.5 0.6 0.6 0.6 0.6 0.5 0.6 0.6 0.6 0.6 0.5 0.6 0.6 0.6 128.1 146.1 -157.2 -167.1 -178.2 173.6 167.6 163.4 160.4 157.6 154.3 153.5 153.4 154.2 156.9 161.5 169.3 -178.8 -164.6 -151.2 -141.4 -135.9 -134.1 -134.4 -136.1 -139.3 -143.1 -147.4 -152.0 -156.7 -177.1 170.4 161.4 158.1 129.6 100.5 92.4 91.5 82.0 52.9 23.4 11.9 7.9 -1.1 -19.0 -37.4 -54.6 -71.2 -8.5 -20.5 -14.5 -11.1 -10.4 -10.5 -11.0 -11.7 -12.5 -13.4 -14.5 -15.4 -16.4 -17.5 -18.7 -19.9 -21.0 -21.8 -21.9 -21.0 -19.5 -17.7 -15.9 -14.4 -13.0 -11.7 -10.6 -9.6 -8.8 -8.1 -6.1 -5.6 -6.4 -5.9 -5.7 -4.8 -3.8 -3.9 -5.0 -5.9 -4.8 -4.0 -4.2 -4.9 -5.2 -4.9 -4.6 -4.2 TRL Board Layer: 13 Top Metal Rogers RO4350 Inner Metal Bottom Metal → 0.5 oz CU → 0.01” → 0.5 oz CU → 0.5 oz CU ALM-80110 K-Factor Tc = 25°C, Vdd = 5.0V, Vctrl = 5V, Vbias = 4.0V, Zo = 50Ω ALM-80110 Typical Noise Parameters Tc = 25°C, Vdd = 5.0V, Vctrl = 5V, Vbias = 4.0V, Zo = 50Ω Freq (GHz) FMIN (dB) Γopt Mag Ang Rn/Zo 50Ohm Ga (dB) 0.4 4.8 0.5 -79.8 1.2 17.6 0.5 4.5 0.4 -55.8 1.2 17.5 0.6 4.4 0.4 -32.6 1.2 16.8 0.7 4.4 0.3 -10.6 1.2 15.9 0.8 4.3 0.3 11.5 1.1 15.2 0.9 4.4 0.3 30.3 1.1 14.1 1.0 4.5 0.3 46.5 1.0 13.3 1.1 4.7 0.3 61.0 1.0 12.8 1.2 4.8 0.3 72.3 1.0 12.3 1.3 5.0 0.3 82.7 1.0 11.8 1.4 5.1 0.3 91.2 0.9 11.4 1.5 5.3 0.3 99.5 0.9 11.0 1.6 5.5 0.3 106.2 0.9 10.7 1.7 5.6 0.3 113.5 0.8 10.5 1.8 5.8 0.3 119.0 0.8 10.3 1.9 5.9 0.3 125.2 0.8 10.1 2.0 6.2 0.3 130.6 0.8 9.9 2.5 7.2 0.3 155.6 0.7 9.3 3.0 8.2 0.3 171.1 1.0 8.4 3.5 8.8 0.3 -176.8 1.2 6.2 4.0 10.5 0.2 156.3 2.1 3.1 4.5 11.8 0.3 118.6 3.5 0.1 5.0 13.8 0.5 125.8 5.8 -2.6 6.0 17.3 0.8 147.4 11.1 -7.6 14 PCB Layout and Stencil Design 0.675 0.400 0.500 0.300 0.360 0.400 0.400 1.100 3.270 4.800 0.500 0.200 1.500 3.070 4.600 0.360 0.300 2.287 0.900 0.360 2.088 0.900 3.270 4.800 2.870 4.600 PCB Land Pattern (Top View) Stencil Outline 0.400 0.400 0.360 0.400 0.360 4.600 4.800 4.600 4.800 Combined PCB & Stencil Layouts All Dimension are in MM 15 0.475 0.360 Package Dimension 0.940±0.10 5.000±0.10 PIN 1 ALM80110 5.000±0.10 WWYY XXXX 0.340 TOP VIEW SIDE VIEW 5.00 1.80 1.15 PIN 1 Orientation 0.10 0.17 2.20 0.09 0.40 0.13 0.07 2.20 0.10 0.14 2.29 0.55 0.90 0.50 BOTTOM VIEW Note : 1. All dimensions are in milimeters 2. Dimensions are inclusive of plating 3. Dimensions are exclusive of mold flash and metal burr. 16 Device Orientation REEL USER FEED DIRECTION CARRIER TAPE USER FEED DIRECTION Tape Dimensions 17 80110 WWYY XXYY 80110 WWYY XXYY TOP VIEW COVER TAPE 80110 WWYY XXYY END VIEW Part Ordering Information Part Number No. of Devices Container ALM-80110-BLKG 100 Antistatic Bag ALM-80110-TR1G 3000 13” Reel For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2014 Avago Technologies. All rights reserved. AV02-1970EN - August 28, 2014