ASMC-PXB9-TXXXX

ASMC-PxB9-Txxxx Envisium Power PLCC-4 Surface Mount LED Data Sheet Envisium Envisium is the premier class of mid-Power LEDs from Avago and Lumileds utilizing the very best solid-state lighting technologies from these two industry leaders. Envisium LEDs offer unparalleled performance, engineering and design flexibility. For the very first time, customers have options for mid-power LEDs. Features • Industry standard PLCC-4 (Plastic Leaded Chip Carrier) • High reliability LED package • Mid-Power intensity brightness with optimum flux performance using TS AlInGaP dice technologies • Available in Red, Red Orange and Amber colors • High optical efficiency • Higher ambient temperature at the same current possible compared to PLCC-2 • Super wide viewing angle at 120° • Available in 8 mm carrier tape on 7-inch reel • Compatible with both IR and TTW soldering process Description The Envisium Power PLCC-4 SMT LED is an extension of Avago’s PLCC-4 SMT LEDs. The package can be driven at high current due to its superior package design. The product is able to dissipate the heat more efficiently compared to the conventional PLCC-2 SMT LEDs. These LEDs produce higher light output with better flux performance compared to the conventional PLCC-4 SMT LEDs. The Envisium Power PLCC-4 SMT LEDs are designed for higher reliability, better performance, and operate under a wide range of environmental conditions. The performance characteristics of these new mid-power LEDs make them uniquely suitable for use in harsh conditions such as in automotive applications, and in electronics signs and signals. To facilitate easy pick and place assembly, the LEDs are packed in EIA-compliant tape and reel. Every reel is shipped in single intensity and color bin (except for red), to provide close uniformity. These LEDs are compatible with the IR solder reflow process. Due to the high reliability feature of these products, they also can be mounted using through-the-wave soldering process. The Envisium Power PLCC-4 SMT LED is available in 3 colors, red, red-orange and amber. Applications • Interior automotive – Instrument panel backlighting – Central console backlighting – Navigation and audio system – Push button backlighting • Exterior automotive – Turn signals – Side repeaters – CHMSL – Rear combination lamp – Puddle light • Electronic signs and signals – Channel lettering – Contour lighting – Indoor variable message sign • Office automation, home appliances, industrial equipment – Front panel backlighting – Push button backlighting – Display backlighting Package Dimensions 2.8 ± 0.2 2.2 ± 0.2 A C 0.1 TYP. 1.9 ± 0.2 0.8 ± 0.1 3.2 ± 0.2 3.5 ± 0.2 0.8 ± 0.3 C CATHODE MARKING C 0.5 ± 0.1 0.7 ± 0.1 NOTE: ALL DIMENSIONS IN mm. Table 1. Device Selection Guide Intensity Bin V1 Red ASMC-PRB9-TV005 V2 W1 W1 Red Orange ASMC-PHB9-TW005 W2 X1 V1 Amber ASMC-PAB9-TV005 V2 W1 Min. IV (mcd) 715.0 900.0 1125.0 1125.0 1400.0 1800.0 715.0 900.0 1125.0 Max. IV (mcd) 900.0 1125.0 1400.0 1400.0 1800.0 2240.0 900.0 1125.0 1400.0 Total Flux FV (mlm)[2,3] Typ. 2600.0 3300.0 4300.0 5000.0 2600.0 3800.0 50 AlInGaP 50 AlInGaP 50 AlInGaP Test Current (mA) Dice Technology Color Part Number Notes 1. The luminous intensity, IV, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern may not be aligned with this axis. 2. FV is the total luminous flux output as measured with an integrating sphere after the device has stabilized. 3. Flux tested at mono pulse conditions. 4. Tolerance = ±12% 2 Part Numbering System A S M C - PX 1 B 9 - T X 2 X 3 X 4 X 5 Packaging Option Color Bin Selection Intensity Bin Limit Intensity Bin Selection LED Chip Color Absolute Maximum Ratings (TA = 25°C) Parameters DC Forward Current[1] Peak Forward Current[2] Power Dissipation Reverse Voltage Junction Temperature Operating Temperature Storage Temperature ASMC-PxB9-Txxxx 70 mA[3,4] 200 mA 240 mW 5 V 125°C -40°C to +100°C -40°C to +100°C Notes: 1. Derate linearly as shown in figure 4. 2. Duty factor = 10%, Frequency = 1 kHz. 3. Drive current between 10 mA and 70 mA is recommended for best long-term performance. 4. Operation at currents below 5 mA is not recommended. Optical Characteristics (TA = 25°C) Color Red Amber Part Number ASMC-PRB9-Txxx5 ASMC-PAB9-Txxx5 Dice Technology AlInGaP AlInGaP Peak Wavelength lPEAK (nm) Typ. 639.0 623.0 594.0 Dominant Wavelength lD[1] (nm) Typ. 630.0 617.0 592.0 Viewing Angle 2q1/2[2] (Degrees) Typ. 120 120 120 Luminous Efficacy hV[3] (lm/W) Typ. 155 263 500 Luminous Intensity/ Total Flux IV (mcd)/ FV[4] (lm) Typ. 0.30 0.29 0.26 Red Orange ASMC-PHB9-Txxx5 AlInGaP Notes: 1. The dominant wavelength, lD, is derived from the CIE Chromaticity Diagram and represents the color of the device. 2. q1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity. 3. Radiant intensity, Ie in watts/steradian, may be calculated from the equation Ie = IV/hV, where IV is the luminous intensity in candelas and hV is the luminous efficacy in lumens/watt. 4. FV is the total luminous flux output as measured with an integrating sphere at mono pulse conditions. Electrical Characteristics (TA = 25°C) Forward Voltage VF (Volts) @ IF = 50 mA Part Number Typ. Max. ASMC-PxB9-Txxx5 2.8 3.4 Reverse Voltage VR @ 100 µA Min. 5 3 1.0 0.9 0.8 RELATIVE INTENSITY RED ORANGE AMBER RED 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 380 430 480 530 580 630 680 730 780 WAVELENGTH – nm Figure 1. Relative intensity vs. wavelength. 80 RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 50 mA) 1.4 MAXIMUM FORWARD CURRENT – mA 80 70 60 50 40 30 20 10 0 0 20 40 60 80 100 120 70 FORWARD CURRENT – mA 1.2 1.0 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 DC FORWARD CURRENT – mA 60 50 40 30 20 10 0 0 1 2 3 4 FORWARD VOLTAGE – V AMBIENT TEMPERATURE – °C Figure 2. Forward current vs. forward voltage. Figure 3. Relative intensity vs. forward current. Figure 4. Maximum forward current vs. ambient temperature. Derated based on TJMAX = 125°C, RqJA = 300°C/W. 1.0 0.9 0.8 RELATIVE INTENSITY 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -90 -70 -50 -30 -10 10 30 50 70 90 ANGLE – DEGREES Figure 5. Radiation pattern. 4 20 SEC. MAX. TEMPERATURE 240°C MAX. 3°C/SEC. MAX. 100-150°C 3°C/SEC. MAX. 120 SEC. MAX. TIME 60-150 SEC. 183°C –6°C/SEC. MAX. Figure 6a. Recommended Sn-Pb reflow soldering profile. 10 to 20 SEC. 217 °C +5 °C 255 °C -0 °C 6 °C/SEC. MAX. TEMPERATURE 3 °C/SEC. MAX. 125 °C ± 25 °C MAX. 120 SEC. 60 to 150 SEC. TIME * THE TIME FROM 25 °C TO PEAK TEMPERATURE = 6 MINUTES MAX. Figure 6b. Recommended Pb-free reflow soldering profile. Note: For detailed information on reflow soldering of Avago surface mount LEDs, do refer to Avago Application Note AN 1060, Surface Mounting SMT LED Indicator Components. TURBULENT WAVE 250 200 150 FLUXING LAMINAR WAVE HOT AIR KNIFE BOTTOM SIDE OF PC BOARD TEMPERATURE – °C TOP SIDE OF PC BOARD CONVEYOR SPEED = 1.83 M/MIN (6 FT/MIN) PREHEAT SETTING = 150°C (100°C PCB) SOLDER WAVE TEMPERATURE = 245°C AIR KNIFE AIR TEMPERATURE = 390°C AIR KNIFE DISTANCE = 1.91 mm (0.25 IN.) AIR KNIFE ANGLE = 40° SOLDER: SN63; FLUX: RMA NOTE: ALLOW FOR BOARDS TO BE SUFFICIENTLY COOLED BEFORE EXERTING MECHANICAL FORCE. 100 50 30 0 10 PREHEAT 20 30 40 50 60 70 80 90 100 TIME – SECONDS Figure 7. Recommended wave soldering profile. 5 4.05 SOLDER-RESIST 3.8 3.4 4.05 A C 8.5 PAD CLEARANCE C 0.5 C 4.05 1.1 0.2 8.5 PAD CLEARANCE REPRESENTS ELECTRICAL CONNECTION BETWEEN THE CATHODE PADS Figure 8. Recommended soldering pad pattern. TRAILER 200 mm MIN. FOR ∅180 REEL. 200 mm MIN. FOR ∅330 REEL. COMPONENT LEADER 480 mm MIN. FOR ∅180 REEL. 960 mm MIN. FOR ∅330 REEL. C A USER FEED DIRECTION Figure 9. Tape leader and trailer dimensions. 6 ∅1.5 +0.1/-0 4 ± 0.1 2 ± 0.05 B 1.75 ± 0.1 3.6 ± 0.1 A A 5.5 ± 0.05 12 +0.3/-0.1 3.8 ± 0.1 C C C ∅1 +0.1/-0 B 3.45 ± 0.1 A 8 ± 0.1 0.229 ± 0.01 VIEW B-B VIEW A-A ALL DIMENSIONS ARE IN MILLIMEERS (mm). Figure 10. Tape dimensions. USER FEED DIRECTION CATHODE SIDE PRINTED LABEL Figure 11. Reeling orientation. This product is qualified as Moisture Sensitive Level 2a per Jedec JSTD-020. Precaution when handling this moisture sensitive product is important to ensure the reliability of the product. Do refer to Avago Application Note AN5305 Handling of Moisture Sensitive Surface Mount Devices for details. A. Storage before use – Unopen moisture barrier bag (MBB) can be stored at