ASMC-QHB2-TCD0E

ASMC-QxB2-Txxxx Envisium 0.5W Power PLCC-4 Surface Mount LED Indicator Data Sheet Envisium Envisium is the premier class of mid-Power LEDs from Avago and Philips Lumileds utilizing the very best solidstate lighting technologies from these two industry leaders. Envisium LEDs offer unparalleled performance, engineering and design flexibility. Features • Industry Standard PLCC 4 platform (3.2 x 2.8 x 1.9mm) • High reliability LED package • Mid-Power intensity brightness with optimum flux performance using Philips Lumileds TS AllnGaP chip technologies • Available in Red Orange and Amber colors • High optical efficiency • Available in 8mm carrier tape and 7 inch reel • Low Thermal Resistance • Super wide viewing angle at 120° • Longer life time with minimum degradation due to enhanced silicone resin material • JEDEC MSL 2a Description The Envisium 0.5W Power PLCC-4 SMT LED is an extension of Envisium Power PLCC-4 SMT LEDs. The package can be driven at high current due to its superior package design. The product is able to dissipate the heat more efficiently compared to the Envisium Power PLCC-4 SMT LEDs. These LEDs produce higher light output with better flux performance compared to the Envisium Power PLCC-4 SMT LED. The Envisium 0.5W Power PLCC-4 SMT LEDs are designed for higher reliability, better performance, and operate under a wide range of environmental conditions. The performance characteristics of these new mid-power LEDs make them uniquely suitable for use in harsh conditions such as in automotive applications, and in electronics signs and signals. To facilitate easy pick and place assembly, the LEDs are packed in EIA-compliant tape and reel. Every reel is shipped in single intensity and color bin (except for red), to provide close uniformity. These LEDs are compatible with the IR solder reflow process. Due to the high reliability feature of these products, they also can be mounted using through-the-wave soldering process. Envisium 0.5W Power PLCC-4 SMT LED is available in red orange & amber colors. Applications 1. Exterior automotive - Turn signals - Side repeaters - CHSML - Rear combination lamp - Side markers - Truck clearance lamp 2. Electronic signs and signals - Channel lettering - Contour lighting - Indoor variable message sign 3. Office automation, home appliances, industrial equipment - Front panel backlighting - Push button backlighting - Display backlighting  Component Dimensions 2.8±0.2 A 2.2±0.2 A 0.8±0.1 Ø 2.40 3.6±0.2 1.9±0.2 0.15 (TYP.) 1.15±0.05 0.41 (TYP.) 0.56 (TYP.) 3.2±0.2 CATHODE MARKING 0.7±0.1 0.8±0.3 C C 2.30±0.05 Note: 1. All Dimensions in millimeters. 2. Lead Polarity as shown in Figure 12. Figure 1. Package Drawing Table 1. Device Selection Guide Luminous Flux, fV [1] (lm) Color Part Number Min. Flux (lm) Typ. Flux (lm) Max. Flux (lm) Test Current (mA) Dice Technology Amber Red Orange ASMC-QAB-TAC0E ASMC-QHB-TCD0E 4.30 7.00 6.60 9.30 9.00 .50 50 50 AlInGaP AlInGaP Notes: 1. fV is the total luminous flux output as measured with an integrating sphere at mono pulse conditions. 2. Tolerance = ±12% Part Numbering System A S M C - Q X1 B 2 - T X2 X3 X4 X5 Packaging Option Color Bin Selection Max. Flux Bin Min. Flux Bin LED Chip Color  Table 2. Absolute Maximum Ratings (TA = 25 °C) Parameters ASMC-QxB2-Txxxx DC Forward Current [] Peak Forward Current [] Power Dissipation Reverse Voltage Junction Temperature Operating Temperature Storage Temperature Notes: 1. Derate Linearly as shown in Figure 6. 2. Duty Factor = 10%, Frequency = 1kHz 50 mA 300 mA 470 mW 5V 5 °C -40 °C to +00 °C -40 °C to +00 °C Table 3. Optical Characteristics (TA = 25 °C) Dominant Wavelength lD [1] (nm) Typ. Viewing Angle 2q½ [2] (Degrees) Typ. Luminous Efficacy hV [3] (lm/W) Typ. Luminous Efficiency he (lm/W) Typ. Luminous Intensity / Total Flux [4, 5] IV (cd) / fV (lm) Typ. Color Part Number Dice Technology Amber Red Orange ASMC-QAB-Txxxx ASMC-QHB-Txxxx AlInGaP AlInGaP 593.5 69.3 0 0 470 40 7 4 0.5 0.0 Notes: 1. The dominant wavelength, lD, is derived from the CIE Chromaticity diagram and represents the color of the device. 2. q½ is the off-axis angle where the luminous intensity is ½ the peak intensity. 3. Radiant intensity, Ie in watts / steradian, may be calculated from the equation Ie = IV / hV, where IV is the luminous intensity in candelas and hV is the luminous efficacy in lumens / watt. 4. fV is the total luminous flux output as measured with an integrating sphere after the device has stabilized. 5. Flux tested at mono pulse conditions. Table 4. Electrical Characteristics (TA = 25 °C) Forward Voltage VF ( Volts) @ IF = 150 mA Part Number Typ. Max. Reverse Voltage VR @ 100mA Min. Thermal Resistance RqJ-P (°C/W) ASMC-QxB-Txxxx .64 3.0 5 60 3 1.0 0.9 0.8 RELATIVE INTENSITY 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 380 430 480 530 580 WAVELENGTH - nm 630 680 730 780 AlInGaP Amber AlInGaP Red Orange Figure 2. Relative Intensity Vs. Wavelength 350 300 1.2 1.0 0.8 0.6 0.4 0.2 0 0 1 2 3 4 5 FORWARD VOLTAGE - V 250 200 150 100 50 0 AlInGaP Red Orange AlInGaP Amber RELATIVE LUMINOUS INTENSITY (NORMALIZATION AT 150 mA) FORWARD CURRENT - mA 0 20 40 60 80 100 120 140 160 DC FORWARD CURRENT - mA Figure 3. Forward Current Vs. Forward Voltage 1.6 1.4 Figure 4. Relative Intensity Vs. Forward Current RELATIVE LUMINOUS INTENSITY (NORMALIZATION AT 25°C) 1.2 1 0.8 0.6 0.4 0.2 0 -50 -25 0 25 50 75 JUNCTION TEMPERATURE - °C 100 125 Figure 5. Relative Intensity Vs. Temperature 4 160 140 MAXIMUM FORWARD CURRENT - mA 120 100 80 60 40 20 0 Rθ�JA = 110°C/W Rθ JA = 130°C/W Rθ JA = 100°C/W MAXIMUM FORWARD CURRENT - mA 160 140 120 100 80 60 40 20 0 Rθ JP = 60°C/W 0 20 40 60 80 AMBIENT TEMPERATURE (°C) 100 120 0 20 40 60 80 SOLDER POINT TEMPERATURE (°C) 100 120 Figure 6a. Maximum Forward Current Vs. Ambient Temperature. Derated Based on TJMAX = 125°C, RqJ-A=130 °C/W, 110°C/W and 100°C/W Figure 6b. Maximum Forward Current Vs. Solder Point Temperature. Derated Based on TJMAX = 125°C, RqJP = 60°C/W 630 RED ORANGE 620 DOMINANT WAVELENGTH - nm 610 600 AMBER 590 580 570 1 2 5 10 20 CURRENT - mA 50 100 150 Figure 7. Dominant Wavelength Vs. Forward Current - AlInGaP Devices 0.15 0.1 NORMALIZED INTENSITY 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -90 -60 -30 0 30 ANGULAR DISPLACEMENT - DEGREES 60 90 FORWARD VOLTAGE SHIFT - V 0.05 0 -50 -25 -0.05 -0.1 -0.15 T J - JUNCTION TEMPERATURE - ˚C 0 25 50 75 100 Figure 8. Forward Voltage Shift Vs. Temperature Figure 9. Radiation Pattern 5 D Note: Diameter "D" should be smaller than 2.2mm Figure 10. Recommended Pick and Place Nozzle Size Figure 11. Recommended Pb-free Reflow Soldering Profile Note: For detail information on reflow soldering of Avago surface mount LEDs, do refer to Avago Application Note AN 1060 Surface Mounting SMT LED Indicator Components ² Figure 12. Recommended Soldering Pad Pattern 6 Figure 13. Tape Leader and Trailer Dimensions Figure 14. Tape Dimensions Figure 15. Reeling Orientation 7 Device Color (X1) A H Amber Red Orange Color Bin Select (X4) Individual reel will contain parts from one full bin only. X4 0 A B C D E G Min. (lm) Max. (lm) Flux Bin Select (X2X3) Individual reel will contain parts from one bin only X X3 Min Flux Bin Max Flux Bin Full Distribution  and  only  and 3 only 3 and 4 only 4 and 5 only 5 and 6 only ,  and 3 only , 3 and 4 only 3, 4 and 5 only 4, 5 and 6 only , , 3 and 4 only , 3, 4 and 5 only 3, 4, 5 and 6 only , , 3, 4 and 5 only , 3, 4, 5 and 6 only Special Color Bin Flux Bin Limits Bin ID H J K M N P R S Z A B C D E F G H I J K 4.30 5.50 7.00 9.00 .50 5.00 9.50 5.50 33.00 43.00 56.00 5.50 7.00 9.00 .50 5.00 9.50 5.50 33.00 43.00 56.00 73.00 Color Bin Limits Amber/Yellow Min. (nm) Max. (nm) Tolerance of each bin limit = ± 12%  3 4 5 6 Red Orange 53.0 56.0 59.0 59.0 595.0 Min. (nm) 56.0 59.0 59.0 595.0 59.0 Max. (nm)   3 6.0 66.0 60.0 66.0 60.0 65.0 Tolerance of each bin limit = ±1nm  Packaging Option (X5) Option Test Current Package Type Reel Size Moisture Sensitivity Top Mount 7 Inch This product is qualified as Moisture Sensitive Level 2a per Jedec J-STD-020. Precautions when handling this moisture sensitive product is important to ensure the reliability of the product. Do refer to Avago Application Note AN5305 Handling of Moisture Sensitive Surface Mount Devices for details. E 50mA VF Binning Bin Min. Max. A. Storage before use - Unopen moisture barrier bag (MBB) can be stored at