ASMT-SWBM-NV803

ASMT-SWBM-Nxxxx Surface Mount LED Indicator Data Sheet Description Features The Long-Life White PLCC-4 SMT LEDs is the latest extension to our White PLCC-4 packages where besides having higher flux output, the Long-Life White PLCC-4 is designed to work under a wide range of environment condition, with reliable and stable performance. The structure and materials used for Long-Life White PLCC-4 enable the packages to endure minimal degradation and hence consistent performance throughout the product life time. Moreover, the Long-Life White PLCC-4 SMT LEDs is a 8-binned product for color, an enhance feature from the previous PLCC-4 white who is binned with 6 color binning only. These tigher color binning will ensure better color grouping with better uniformity. • Industry standard PLCC-4 The Long-Life White PLCC-4 SMT LEDs is suitable to be used in Interior Automotive application, Electronics Signs and Signals application. Besides that, the super wide viewing angle at 120° makes these LEDs ideally suited for instrument cluster panel, push button, or general backlighting in automotive interior, office equipment, industrial equipment, and home appliances. The flat top emitting surface makes it easy for these LEDs to mate with light pipes. With the built-in reflector pushing up the intensity of the light output, these super high brightness LEDs can be used in localized area ambience lighting in applications such as vanity mirror light, cabin light, and car door puddle light. The white color backlighting is suitable to backlight color LCD screens in applications such as GPS (global positioning system) screen in cars. To facilitate easy pick and place assembly, the LEDs are packed in EIA-compliant tape and reel. Every reel will be shipped in single intensity and color bin, to provide close uniformity. These LEDs are compatible with IR solder reflow process. • High reliability LED package • Long Life, up to 50,000 hours at 25°C • High brightness using InGaN dice technologies • High optical efficiency • Super wide viewing angle at 120° • Tight white color binning – 8 bins • Available is 8mm carrier tape on 7-inch reel • Stabile & Consistent performance with minimum degradation with Silicone Encapsulation • JEDEC MSL 2a Applications • Interior & exterior automotive – Instrument panel backlighting – Central console backlighting – Navigation and audio system backlighting – Dome/Map lighting – Push button backlighting – Number plate illumination – Rear reverse lamp indicator • Electronic signs and signals – Decorative lighting • Office automation, equipment home appliances, – Front panel backlighting – Push button backlighting CAUTION: ASMT-SWBM-Nxxxx LEDs are Class 2 ESD sensitive. Please observe appropriate precautions during handling and processing. Refer to Avago Application Note AN-1142 for additional details. industrial Package Drawing 2.8 ± 0.2 1.9 ± 0.2 2.2 ± 0.2 A 0.1 TYP. 0.8 ± 0.1 C 3.2 ± 0.2 3.5 ± 0.2 0.8 ± 0.3 C CATHODE MARKING C 0.5 ± 0.1 0.7 ± 0.1 NOTES: ALL DIMENSIONS IN mm. NOTE: ALLCONNECTION DIMENSIONSBETWEEN IN mm. ALL CATHODES IS RECOMMENDED. ELECTRICAL Table 1. Device Selection Guide Color Part Number Min. IV (mcd) Typ. IV (mcd) Max. IV (mcd) Test Current (mA) Dice Technology White ASMT-SWBM-NU803 560.00 1100.00 1400.00 30 InGaN White ASMT-SWBM-NV803 900.00 - 2240.00 30 InGaN Notes: 1. The luminous intensity IV, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern may not be aligned with this axis. 2. IV tolerance ±12% Part Numbering System A S M T – S X1 B M – NX2 X3 X4 X5 Packaging Option Color Bin Selection Intensity Bin Limit Intensity Bin Selection LED Chip Color 2 Table 2. Absolute Maximum Ratings (TA = 25°C) Parameters ASMT-SWBM-Nxxxx DC Forward Current [1] 50 mA Peak Forward Current [2] 300 mA Power Dissipation 215 mW Reverse Voltage 4V Junction Temperature 125°C Operating Temperature - 40°C to + 110°C Storage Temperature - 40°C to + 110°C Notes: 1. Derate linearly as shown in Figure 4. 2. Duty Factor = 0.5%, Frequency = 500Hz. Table 3. Optical Characteristics (TA = 25°C) Color Part Number Dice Technology White ASMT-SWBM-Nxxxx InGaN Typical Chromaticity Coordinates[1] Viewing Angle 2q½ [2] (Degrees) Luminous Efficiency he (lm/W) Total Flux [3] / Luminous Intensity φV (lm) / IV (cd) x y Typ. Typ. Typ 0.318 0.318 120 27 2.7 Notes: 1. The chromaticity coordinates are derived from the CIE 1931 Chromaticity Diagram and represent the perceived color of the device. 2. q½ is the off-axis angle where the luminous intensity is ½ the peak intensity. 3. φV is the total luminous flux output as measured with an integrating sphere at mono pulse conditions. Table 4. Electrical Characteristics (TA = 25°C) Forward Voltage VF (Volts) @ IF = 30 mA [1] Reverse Voltage VR @ 10µA Part Number Typ. Max. Min. Thermal Resistance RqJ-P (°C/W) ASMT-SWBM-Nxxxx 3.2 3.8 4 110 Notes: 1. Tolerance = ±0.1V Table 5. Targeted Mean Lifetime Conditions Mean Luminous Maintenance (L50) Unit IF = 25mA TA = 85°C 25,000 Operating hours IF = 25mA TA = 25°C 50,000 Operating hours Notes: 1. The typical data or calculated correlations can only reflect statistical figure, hence can only be used for reference only 2. All data shown based on Thermal Resistance RθJA=300°C/W. 3. Due to technical improvement,Avago technologies reserved right to change the typical data without any further notice. 3 50 FORWARD CURRENT - mA RELATIVE INTENSITY 60 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 380 430 480 530 580 630 WAVELENGTH - nm 680 730 MAXIMUM FORWARD CURRENT - mA RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 30 mA) 1.2 0.8 0.4 0 10 20 30 40 DC FORWARD CURRENT - mA 50 NORMALIZED INTENSITY MAXIMUM FORWARD CURRENT - mA 2 4 FORWARD VOLTAGE - V 6 40 30 20 10 20 40 60 80 100 SOLDER POINT TEMPERATURE (°C) 40 30 20 10 0 20 40 60 80 AMBIENT TEMPERATURE - °C 100 120 Figure 4a. Maximum Forward Current Vs. Ambient Temperature. Derated Based on TJMAX = 125°C, RqJA=300°C/W 50 Figure 4b. Maximum forward current vs. solder point temperature. Derated Based on TJMAX = 125°C, RqJP=110°C/W 4 0 50 0 55 60 0 10 60 Figure 3. Relative Intensity Vs. Forward Current 0 20 Figure 2. Forward Current Vs. Forward Voltage 1.6 0 30 0 780 Figure 1. Relative Intensity Vs. Wavelength 40 120 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -90 -60 -30 0 30 60 ANGULAR DISPLACEMENT - DEGREES Figure 5. Radiation Pattern 90 10 - 30 SEC. ID Note: Diameter "ID" should be bigger than 2.3mm TEMPERATURE 255 - 260°C 217°C 200°C 3°C/SEC. MAX. 6°C/SEC. MAX. 150°C 3°C/SEC. MAX. 60 - 120 SEC. 100 SEC. MAX. TIME Figure 6. Recommended Pick and Place Nozzle Size (Acc. to J-STD-020C) Note: For detail information on reflow soldering of Avago surface mount LEDs, do refer to Avago Application Note AN 1060 Surface Mounting SMT LED Indicator Components Figure 7. Recommended Pb-free Reflow Soldering Profile 4.05 3.8 SOLDER-RESIST 3.4 A 4.05 C 1.1 8.5 PAD CLEARANCE C C 4.05 0.5 0.2 8.5 PAD CLEARANCE REPRESENTS ELECTRICAL CONNECTION BETWEEN THE CATHODE PADS Figure 8. Recommended Soldering Pad Pattern 5 TRAILER 200 mm MIN. FOR Ø180 REEL. 200 mm MIN. FOR Ø330 REEL. COMPONENT LEADER 480 mm MIN. FOR Ø180 REEL. 960 mm MIN. FOR Ø330 REEL. C A USER FEED DIRECTION Figure 9. Tape Leader and Trailer Dimensions Ø1.5 +0.1 –0 4 ± 0.1 4 ± 0.1 2 ± 0.05 1.75 ± 0.1 2.29 ± 0.1 3.5 ± 0.05 8 +0.3 –0.1 3.05 ± 0.1 +0.1 Ø1 –0 Figure 10. Tape Dimensions USER FEED DIRECTION CATHODE SIDE PRINTED LABEL Figure 11. Reeling Orientation 6 C C A 3.8 ± 0.1 0.229 ± 0.01 8° ALL DIMENSIONS IN mm. C Handling Precaution The encapsulation material of the product is made of silicone for better reliability of the product. As silicone is a soft material, please do not press on the silicone or poke a sharp object onto the silicone. These might damage the product and cause premature failure. During assembly or handling, the unit should be held on the body only. Please refer to Avago Application Note AN 5288 for detail information. Moisture Sensitivity This product is qualified as Moisture Sensitive Level 2a per JEDEC J-STD-020. Precautions when handling this moisture sensitive product is important to ensure the reliability of the product. For details, refer to Avago Application Note AN5305 Handling of Moisture Sensitive Surface Mount Devices. A. Storage before use - Unopen moisture barrier bag (MBB) can be stored at