ASMT-TWBM-NV7H2

ASMT-TWBM-Nxxxx Surface Mount LED Indicator Data Sheet Description Features Avago Technologies' ASMT-TWBM-Nxxxx Mini PLCC-2 SMT LEDs are designed specifically for use in Automotive Interior applications. They have a wide viewing angle of 110q making them ideally suited for instrument cluster panel, push button, HVAC and ambient decorative lighting applications in automotive interiors. x Industry standard Mini PLCC-2 The LEDs are packed in EIA-compliant tape and reel to facilitate easy pick and place assembly. Every reel will be shipped in single intensity and color bin, to provide close uniformity. x Available is 8 mm carrier tape on 7-inch reel x High reliability LED package x High brightness using InGaN dice technologies x High optical efficiency x Wide viewing angle at 110° x Stable & consistent performance with minimum degradation x JEDEC MSL 2 Applications x Interior automotive – Instrument panel backlighting – Central console backlighting – Navigation and audio system backlighting – Push button backlighting – Ambient illumination – Car puddle lighting CAUTION: ASMT-TWBM-Nxxxx LED is Class 1B ESD sensitive. Please observe appropriate precautions during handling and processing. Refer to Avago Application Note AN-1142 for additional details. Package Dimensions 1.3 ±0.2 1.4 ±0.2 0.7 ±0.2 0.1 TYP. 0.9 ±0.2 1.5 ±0.2 2.0 ±0.2 2.3 ±0.2 0.6 ±0.3 CATHODE MARKING 1.0 ±0.2 Notes: 1. All dimensions in millimeters. 2. Terminal Finish: Ag plating. 3. Encapsulation material: Silicone resin. Figure 1. Package Drawing Table 1. Device Selection Guide Color Part Number Min. Iv (mcd) Typ. Iv (mcd) Max. Iv (mcd) Test Current (mA) Dice Technology Cool White ASMT-TWBM-NV7H2 900.00 - 1800.00 20 InGaN Cool White ASMT-TWBM-NV702 900.00 - 1800.00 20 InGaN Cool White ASMT-TWBM-NV8H2 900.00 - 2240.00 20 InGaN Notes: 1. The luminous intensity IV, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern may not be aligned with this axis. 2. Tolerance = ±12% Part Numbering System ASMT  T X1 B M  N X2 X3 X4 X5 Packaging Option Color Bin Selection Intensity Bin Selection Color W – White 2 Table 2. Absolute Maximum Ratings (TA = 25°C) Parameters ASMT-TWBM-Nxxxx DC Forward Current [1] 20 mA Peak Forward Current [2] 100 mA Power Dissipation 72 mW Reverse Voltage, VR @ 10 PA Not Recommended for Reverse Bias Junction Temperature 110 °C Operating Temperature -40 °C to +100 °C Storage Temperature -40 °C to +100 °C Notes: 1. Derate Linearly as shown in Figure 6. 2. Duty Factor = 10%, Frequency = 1 kHz Table 3. Optical Characteristics (TJ = 25 qC) Color Part Number Dice Technology Cool White ASMT-TWBM-Nxx02 InGaN Typical Chromaticity Coordinates[1] Viewing Angle 2T½[2] (Degrees) Total Flux / Luminous Intensity )V (lm) / IV (cd) x y Typ. Typ. 0.34 0.34 110 2.5 Notes: 1. The dominant wavelength, OD, is derived from the CIE Chromaticity diagram and represents the color of the device. 2. T½ is the off-axis angle where the luminous intensity is ½ the peak intensity. Table 4. Electrical Characteristics (TJ = 25 qC) Forward Voltage VF (Volts) @ IF = 20 mA Part Number Min. Typ. Max. Thermal Resistance RTJP (°C/W) ASMT-TWBM-Nxx02 2.8 3.2 3.6 230 3 100 FORWARD CURRENT - mA RELATIVE INTENSITY 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 380 60 40 20 0 430 480 530 580 630 WAVELENGTH - nm 680 730 0 780 Figure 2. Relative Intensity Vs. Wavelength 1 2 3 FORWARD VOLTAGE - V 4 5 Figure 3. Forward Current Vs. Forward Voltage 1.2 NORMALIZED LUMINOUS INTENSITY 3.0 RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20 mA) 80 2.5 2.0 1.5 1.0 0.5 0.0 0 10 20 30 40 50 60 70 80 DC FORWARD CURRENT - mA 0.8 0.6 0.4 0.2 0.0 -50 90 100 Figure 4. Relative Luminous Intensity Vs. Forward Current 1.0 -25 0 25 50 75 TJ - JUNCTION TEMPERATURE - °C 100 125 Figure 5. Relative Intensity Vs. Temperature 25 0.002 RTJA = 850°C/W 0.001 RTJA = 480°C/W COORDINATE SHIFT CURRENT (mA) 20 15 10 0 20 40 60 80 TEMPERATURE (°C) 100 Figure 6. Maximum Forward Current Vs. Ambient Temperature. Derate Based on TJMAX = 110 °C, RTJA=850 °C/W, 480 °C/W 4 Cx -0.001 -0.002 5 0 Cy 0.000 120 -0.003 0 20 40 60 FORWARD CURRENT - mA Figure 7. Chromaticity Shift Vs. Forward Current 80 100 0.2 NORMALIZED INTENSITY FORWARD VOLTAGE SHIFT - V 0.3 0.1 0.0 -0.1 -0.2 -0.3 -50 -25 0 25 50 TJ - JUNCTION TEMPERATURE - °C 75 Figure 8. Forward Voltage Shift Vs. Temperature 100 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -90 -60 -30 0 30 60 ANGULAR DISPLACEMENT - DEGREES Figure 9. Radiation Pattern 240°C MAX. 3°C/SEC. MAX. 100-150°C 183°C -6°C/SEC. MAX. 3°C/SEC. MAX. 60-120 SEC. TIME 10 - 30 SEC. TEMPERATURE TEMPERATURE 20 SEC. MAX. 120 SEC. MAX. 90 217°C 200°C 255 - 260°C 3°C/SEC. MAX. 6°C/SEC. MAX. 150°C 3°C/SEC. MAX. 100 SEC. MAX. 60 - 120 SEC. TIME (Acc. to J-STD-020C) Figure 10a. Recommended SnPb Reflow Soldering Profile 2.8 0.8 1.0 Figure 11. Recommended Soldering Pad Pattern 5 Figure 10b. Recommended Pb-Free Reflow Soldering Profile 4.0 ±0.10 4.0 ±0.10 2.0 ±0.05 1.5 ±0.10 1.75 ±.10 3.50 ±0.05 ±0.30 8.0 0.10 0.6 ±0.05 0.254 ± 0.02 9° MAX 8° MAX 1.60 ± 0.10 1.50 ± 0.10 Figure 12. Tape Leader and Trailer Dimensions USER FEED DIRECTION CATHODE SIDE PRINTED LABEL Figure 13. Reeling Orientation 6 2.55 ± 0.10 Handling Precaution The encapsulation material of the product is made of silicone for better reliability of the product. As silicone is a soft material, please do not press on the silicone or poke a sharp object onto the silicone. These might damage the product and cause premature failure. During assembly or handling, the unit should be held on the body only. Please refer to Avago Application Note AN 5288 for detail information. Moisture Sensitivity This product is qualified as Moisture Sensitive Level 2a per Jedec J-STD-020. Precautions when handling this moisture sensitive product is important to ensure the reliability of the product. Do refer to Avago Application Note AN5305 Handling of Moisture Sensitive Surface Mount Devices for details. A. Storage before use - Unopen moisture barrier bag (MBB) can be stored at < 40 °C/90% RH for 12 months. If the actual shelf life has exceeded 12 months and the HIC indicates that baking is not required, then it is safe to reflow the LEDs per the original MSL rating. - It is not recommended to open the MBB prior to assembly (e.g., for IQC). B. Control after opening the MBB - The humidity indicator card (HIC) shall be read immediately upon opening of MBB. - The LEDs must be kept at 30 °C / 60% RH at any time. - The LEDs floor life exceeded 672 hours. Recommended baking condition: 60 ± 5 ºC for 20hrs Device Color (X1) W Color Bin Select (X4) Individual reel will contain parts from one sub bin only. White X4 0 Full Distribution Intensity Bin Select (X2X3) A 5K and 5L only Individual reel will contain parts from one half bin only B 6K and 6L only C 7K and 7L only D 8K and 8L only X2 Min IV Bin X3 0 E 5K and 6K only Full Distribution F 5L and 6L only 2 2 half bins starting from X21 G 6K and 7K only 3 3 half bins starting from X21 H 6L and 7L only 4 4 half bins starting from X21 J 7K and 8K only 5 5 half bins starting from X21 K 7L and 8L only 6 2 half bins starting from X22 L 5K, 5L, 6K and 6L only 7 3 half bins starting from X22 M 6K, 6L, 7K and 7L only 8 4 half bins starting from X22 N 7K, 7L, 8K and 8L only 9 5 half bins starting from X22 Z Special binning Intensity Bin Limits Bin ID Min. (mcd) Max. (mcd) T1 285.00 355.00 T2 355.00 450.00 U1 450.00 560.00 U2 560.00 715.00 V1 715.00 900.00 V2 900.00 1125.00 W1 1125.00 1400.00 W2 1400.00 1800.00 X1 1800.00 2240.00 X2 2240.00 2850.00 Tolerance of each bin limit = ± 12% 8 Color Bin Limits Bin ID Sub Bin ID Limits (Chromaticity Coordinates) 5K 5Ka 5Kb 5Kc 5Kd 5L 5La 5Lb 5Lc 5Ld 6K 6Ka 6Kb 6Kc 6Kd 6L 6La 6Lb 6Lc 6Ld x 0.296 0.304 0.302 0.294 y 0.259 0.270 0.276 0.264 x 0.294 0.302 0.300 0.291 y 0.264 0.276 0.281 0.268 x 0.304 0.313 0.312 0.302 y 0.270 0.284 0.291 0.276 x 0.302 0.312 0.310 0.300 y 0.276 0.291 0.297 0.281 x 0.291 0.300 0.298 0.288 y 0.268 0.281 0.288 0.274 x 0.288 0.298 0.295 0.285 y 0.274 0.288 0.294 0.279 x 0.300 0.310 0.309 0.298 y 0.281 0.297 0.305 0.288 x 0.298 0.309 0.307 0.295 y 0.288 0.305 0.312 0.294 x 0.313 0.322 0.321 0.312 y 0.284 0.297 0.305 0.291 x 0.312 0.321 0.320 0.310 y 0.291 0.305 0.314 0.297 x 0.322 0.330 0.330 0.321 y 0.297 0.310 0.320 0.305 x 0.321 0.330 0.330 0.320 y 0.305 0.320 0.330 0.314 x 0.310 0.320 0.319 0.309 y 0.297 0.314 0.322 0.305 x 0.309 0.319 0.318 0.307 y 0.305 0.322 0.329 0.312 x 0.320 0.330 0.330 0.319 y 0.314 0.330 0.339 0.322 x 0.319 0.330 0.330 0.318 y 0.322 0.339 0.347 0.329 Bin ID Sub Bin ID Limits (Chromaticity Coordinates) 7K 7Ka 7Kb 7Kc 7Kd 7L 7La 7Lb 7Lc 7Ld 8K 8Ka 8Kb 8Kc 8Kd 8L 8La 8Lb 8Lc 8Ld x 0.330 0.336 0.337 0.330 y 0.310 0.320 0.330 0.320 x 0.330 0.337 0.337 0.330 y 0.320 0.330 0.341 0.330 x 0.336 0.343 0.344 0.337 y 0.320 0.331 0.341 0.330 x 0.337 0.344 0.345 0.337 y 0.330 0.341 0.352 0.341 x 0.330 0.337 0.337 0.330 y 0.330 0.341 0.349 0.339 x 0.330 0.337 0.338 0.330 y 0.339 0.349 0.358 0.347 x 0.337 0.345 0.346 0.337 y 0.341 0.352 0.362 0.349 x 0.337 0.346 0.347 0.338 y 0.349 0.362 0.371 0.358 x 0.343 0.351 0.352 0.344 y 0.331 0.343 0.354 0.341 x 0.344 0.352 0.354 0.345 y 0.341 0.354 0.364 0.352 x 0.351 0.360 0.362 0.352 y 0.343 0.357 0.369 0.354 x 0.352 0.362 0.364 0.354 y 0.354 0.369 0.380 0.364 x 0.345 0.354 0.355 0.346 y 0.352 0.364 0.375 0.362 x 0.346 0.355 0.356 0.347 y 0.362 0.375 0.385 0.371 x 0.354 0.364 0.366 0.355 y 0.364 0.380 0.391 0.375 x 0.355 0.366 0.367 0.356 y 0.375 0.391 0.401 0.385 Tolerance of each bin limit = ± 0.02. 9 Color Coordinates Chart 0.41 0.40 0.39 8Ld 0.38 8Lb 0.37 8La 7Ld 0.36 Y-COORDINATE 0.35 7Lc 8Kb 7Kd 8Ka 8Lc 8Kd 8Kc 7Lb 0.34 7La 5000K – 4500K 6Ld 0.33 7Kc 7Kb 7Ka 6Lc 0.32 6Kd 6Lb 0.31 6La 6Kb 0.30 5Ld 5Lc 0.29 5La 5Kb 5Ka 0.27 6Ka 7000K – 5600K 5Kd 5Lb 0.28 5600K – 5000K 6Kc 5Kc 10000K – 7000K 0.26 0.25 0.28 0.29 0.30 0.31 0.32 0.33 X-COORDINATE 0.34 0.35 0.36 0.37 Packaging Option (X5) Option Test Current Package Type Reel Size 2 20 mA Top Mount 7 Inch For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2014 Avago Technologies. All rights reserved. AV02-2204EN - August 29, 2014