BCM54616SC0IFBG

BCM54616S ® 10/100/1000BASE-T GIGABIT COPPER TRANSCEIVER SUMMARY OF BENEFITS FEATURES • Simplifies system and board design. - Reduced I/O pin requirements with RGMII (over 50%). - On-chip RGMII timing delay on fid en tia l • Single-chip integrated triple-speed Ethernet transceiver. Support for the following copper line interfaces: - 1000BASE-T IEEE 802.3ab - 100BASE-TX IEEE 802.3u - 100BASE-FX - 10BASE-T IEEE 802.3™ • Provides interoperability with IEEE standard devices operating at 10 Mbps, 100 Mbps, and 1000 Mbps at half- and full-duplex. • RGMII and SGMII MAC interface options • Lowers system Bill of Materials (BOM) cost and simplifies system design. • Integrated voltage regulator • Low power - Less than 600 mW per port - Advanced power management • Eases system level debug. • Reduces system design constraints to meet EMI emissions standards. • Trace-matched output impedance • Lineside loopback C • Low Electromagnetic Interference (EMI) emissions • Cable diagnostic function characterizes cable plant condition and immediately indicates cabling issues. - Prevents erroneous equipment return due to bad cable plants. - Prevents manufacturing fallout due to bad cable plants. om • Cable plant diagnostics - Cable plant analyzer function detects cable plant impairments - Link quality indication LED - Automatic detection and correction of wiring pair swaps, pair skew, and pair polarity - Automatic MDI/MDIX crossover at all speeds • Robust Cable Electrostatic Discharge (CESD) tolerance oa dc • Support for jumbo packets up to 10 KB • High CESD tolerance prevents equipment damage and return. • Operates with larger packets for wider range of packet protocol support and improved efficiency. • Ease of manufacturing with JTAG support, simplified power supply, and multiple MAC interfaces. • IEEE 1149.1 (JTAG) boundary scan General Gigabit Ethernet Connectivity BCM5248 BCM5248 BCM5248 Oc tal 10/100 Mbps P HY Oc tal 10/100 Mbps P HY Oc tal 10/100 Mbps P HY R J -45 BCM54616S R J -45 24 F E +2G S witch Trans forme r BCM5645 RJ-45 BCM54616S Transformer MAC BCM54616S Trans forme r Br • 100-pin FBGA package 1000BASE-T Gigabit Uplink OVERVIEW SYMBOL ENCODER TX DAC TRD0+ TRD0TRD1+ TRD1TRD2+ TRD2TRD3+ TRD3- ECHO CANCELLER BASELINE WANDER CORRECTION PGA XTALK CANCELER 3X SGMII EQUALIZER ADC SYMBOL ENCODER/ ALIGNER CLOCK GENERATOR RDAC BIAS GENERATOR REGSUPPLY LED DRIVERS VOLTAGE REGULATOR REGOUT CLK125 RXC RX_DV RXD[3:0] on fid en tia l AUTONEGOTIATION XTALI RXDP RXDN TXDP TXDN DEF/ TRELLIS DECODER TIMING & PHASE RECOVERY XTALO TXD[3:0] TX_EN GTXCLK MII REGISTERS MII MGMT CONTROL LED1 LED2 LED3 LED4 MDC MDIO BCM54616S Reference Design phase-locked loops, line drivers, encoders, decoders, echo cancelers, crosstalk cancelers, and all other required support circuitry. The BCM54616S is designed to be fully compliant with RGMII, SGMII, and MII interface specifications, allowing compatibility with industrystandard Ethernet MACs and switch controllers. om C The BCM54616S is a triple-speed 10/100/1000BASE-T Gigabit Ethernet transceiver integrated into a single monolithic CMOS chip. The device performs all of the Physical Layer (PHY) functions for 1000BASE-T, 100BASE-TX, and 10BASE-T on standard Category 5 UTP cable. The 10BASE-T Ethernet can also run on standard categories 3, 4, and 5 UTP. The BCM54616S is designed to comply with the SGMII industry standard and to exceed IEEE specifications for noise cancellation and transmission jitter, providing consistent and reliable operation over the broadest range of existing cable plants. Br oa dc The BCM54616S is based on the proven digital-signal processor technology of Broadcom, combining digital adaptive equalizers, ADCs, Designed for reliable operation over worst-case Category 5 cable plants, the BCM54616S automatically negotiates with its link partner to determine the highest possible operating speed. The device detects and corrects most common wiring problems. The BCM54616S features CableChecker™ diagnostics, which detects common cable problems, including shorts, opens, and cable length. Broadcom®, the pulse logo, Connecting everything®, the Connecting everything logo, and CableChecker™ are among the trademarks of Broadcom Corporation and/or its affiliates in the United States, certain other countries and/or the EU. Any other trademarks or trade names mentioned are the property of their respective owners. ® BROADCOM CORPORATION 5300 California Avenue, Irvine, California 92617 © 2009 by BROADCOM CORPORATION. All rights reserved. 54616S-PB00-R 04/22/09 Phone: 949-926-5000 Fax: 949-926-5203 E-mail: info@broadcom.com Web: www.broadcom.com