CREQ-9020-MP000

Data Sheet CREQ-9020-xx000 3528 PLCC-4 Surface Mount Infrared LED Overview Features The Broadcom® CREQ-9020-xx000 is a single junction 940-nm infrared emitter packaged in an industrial-standard PLCC-4. This high-efficiency infrared emitter is suitable to be used in industrial sensing and infrared illumination for cameras. The package is compatible with reflow soldering process. To facilitate easy pick and place assembly, the product is packed in tape and reel form.     Available in peak wavelength 940 nm Wide viewing angle at 120° Qualified to AEC-Q101 test guidelines JEDEC MSL 3 Applications   Infrared illumination for cameras Industrial sensing Figure 1: Package Drawing 2.80 1.85 2.20 0.70 3.50 (∅2.40) 3.20 0.80 CATHODE MARK CAUTION! This LED is ESD sensitive. Observe appropriate precautions during handling and processing. Refer to the Premium InGaN LEDs: Safety Handling Fundamentals ESD, application note AN-1142, for additional details. NOTE: 1. All dimensions are in millimeters (mm). 2. Tolerance is ±0.20 mm unless otherwise specified. 3. Terminal finish = silver plating. 4. Dimensions in bracket are for reference only. Broadcom CREQ-9020-xx000-DS100 October 8, 2021 CREQ-9020-xx000 Data Sheet 3528 PLCC-4 Surface Mount Infrared LED Device Selection Guide (TJ = 25°C, IF = 100 mA, tp = 20 ms) Radiant Intensity, Ie (mW/sr)a, b Viewing Angle, 2½ (°) Peak Wavelength, p (nm) Part Number Typ. Typ. Min. Typ. Max. CREQ-9020-MP000 120 940 18.0 30.0 71.5 a. The radiant intensity, Ie, is measured at the mechanical axis of the package and it is tested with a single current pulse condition. The actual peak of the spatial radiation pattern might not be aligned with the axis. b. Tolerance is ±12%. Absolute Maximum Ratings Parameters DC Forward Current CREQ-9020-xx000 Unit 100 mA 1000 mA a b Peak Forward Current Power Dissipation Reverse Voltage LED Junction Temperature Operating Temperature Range Storage Temperature Range 360 mW Not designed for reverse bias operation 125 °C –40 to +100 °C –40 to +100 °C a. Derate linearly as shown in Figure 6 and Figure 7. b. Duty factor = 1%, frequency = 100 Hz, TS = 25°C. Optical and Electrical Characteristics (TJ = 25°C) Parameters Min. Typ. Max. Unit Viewing Angle, 2½ a — 120 — ° Spectral Half-Width, Δλ½ — 41 — nm IF = 100 mA, tp = 20 ms Forward Voltage, VFb — 3.1 3.6 V IF = 100 mA, tp = 20 ms Forward Voltage, VFb — 4.1 — V IF = 1A, tp = 100 µs Rise Time, trc — 15 — ns IF = 100 mA — 25 — ns IF = 100 mA Thermal Resistance, RJ-Sd — 140 — °C/W — Temperature Coefficient of Radiant Intensity, TCIe — –0.15 — %/°C IF = 100 mA, 25°C ≤ T ≤ 85°C Temperature Coefficient of Forward Voltage, TCVF — –2.40 — mV/°C IF = 100 mA, 25°C ≤ T ≤ 85°C Temperature Coefficient of Peak Wavelength, TCλp — 0.31 — nm/°C IF = 100 mA, 25°C ≤ T ≤ 85°C Fall Time, tfc Test Conditions IF = 100 mA a. θ½ is the off-axis angle where the radiant intensity is half of the peak intensity. b. Forward voltage tolerance is ±0.1V. c. 10% and 90% of Ie max. d. Thermal resistance from LED junction to solder point. Broadcom CREQ-9020-xx000-DS100 2 CREQ-9020-xx000 Data Sheet 3528 PLCC-4 Surface Mount Infrared LED Part Numbering System C R E Q x1 - x2 x3 0 - x4 x5 0 0 0 Code Description Option x1 Peak Wavelength 9 940 nm x2 Viewing Angle 0 120° x3 Junction Type 2 Double Junction x4 Minimum Intensity Bin See the Radiant Intensity Bin Limits (CAT) table. x5 Maximum Intensity Bin Part Number Example CREQ-9020-MP000 x1 : 9 – Peak wavelength 940 nm x2 : 0 – 120° viewing angle x3 : 2 – Double junction type x4 : M – Minimum intensity bin M x5 : P – Maximum intensity bin P Bin Information Radiant Intensity Bin Limits (CAT) Radiant Intensity, Ie (mW/sr) Bin ID Min. Max. M 18.0 28.5 N 28.5 45.0 P 45.0 71.5 NOTE: Broadcom Tolerance = ±12%. CREQ-9020-xx000-DS100 3 CREQ-9020-xx000 Data Sheet 3528 PLCC-4 Surface Mount Infrared LED Figure 2: Spectral Power Distribution Figure 3: Forward Current vs. Forward Voltage Figure 4: Relative Radiant Intensity vs. Mono Pulse Current Figure 5: Radiation Pattern Figure 6: Maximum Forward Current vs. Ambient Temperature Figure 7: Maximum Forward Current vs. Solder Point Temperature Broadcom CREQ-9020-xx000-DS100 4 CREQ-9020-xx000 Data Sheet 3528 PLCC-4 Surface Mount Infrared LED Figure 8: Maximum Pulse Current vs. Ambient Temperature at TS ≤ 83°C Figure 9: Maximum Pulse Current vs. Ambient Temperature at TS = 100°C Figure 10: Recommended Soldering Land Pattern 0.4 2.6 1.1 MAXIMIZE COPPER PAD AREA A FOR BETTER HEA AT DISSIPA ATION 4.5 0.5 1.5 COPPER PAD SOLDER MASK REPRESENTS ELECTRICAL CONNECTIVITY BETWEEN PADS NOTE: Broadcom All dimensions are in millimeters (mm). CREQ-9020-xx000-DS100 5 CREQ-9020-xx000 Data Sheet 3528 PLCC-4 Surface Mount Infrared LED Figure 11: Carrier Tape Dimensions P0 P1 P2 ∅D0 K0 E1 F W B0 A0 T PACKAGE MARKING USER FEED DIRECTION F P0 P1 P2 D0 E1 W 3.5 ±0.05 4.0 ±0.1 4.0 ±0.1 2.0 ±0.05 1.5 +0.1/-0 1.75 ±0.1 8.0 +0.3/-0.1 T B0 K0 A0 0.25 ±0.05 3.7 ±0.1 2.15 ±0.1 3.0 ±0.1 NOTE: All dimensions are in millimeters (mm). Figure 12: Reel Dimensions NOTE: Broadcom All dimensions are in millimeters (mm). CREQ-9020-xx000-DS100 6 CREQ-9020-xx000 Data Sheet 3528 PLCC-4 Surface Mount Infrared LED Precautionary Notes Handling of Moisture-Sensitive Devices Soldering      Do not perform reflow soldering more than twice. Observe necessary precautions of handling moisturesensitive device as stated in the following section. Do not apply any pressure or force on the LED during reflow and after reflow when the LED is still hot. Use reflow soldering to solder the LED. Use hand soldering only for rework if unavoidable, but it must be strictly controlled to the following conditions: – Soldering iron tip temperature = 315°C max. – Soldering duration = 3 seconds max. – Number of cycles = 1 only – Power of soldering iron = 50W max. Do not touch the LED package body with the soldering iron except for the soldering terminals because it can cause damage to the LED. Confirm beforehand whether the functionality and performance of the LED is affected by soldering with hand soldering. Figure 13: Recommended Lead-Free Reflow Soldering Profile TEMPERATURE 10 to 30 SEC. 217°C 200°C 255 – 260°C 3°C/SEC. MAX. This product has a Moisture Sensitive Level 3 rating per JEDEC J-STD-020. Refer to the Broadcom Application Note AN5305, Handling of Moisture Sensitive Surface Mount Devices, for additional details and a review of proper handling procedures. Before use:  An unopened moisture barrier bag (MBB) can be stored at