HCNW136-000E

6N135/6, HCNW135/6 HCPL-2502/0500/0501 Single Channel, High Speed Optocouplers Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features These diode-transistor opto­ coup­ lers use an insulating layer between a LED and an integrated photodetector to provide elec­trical in­su­lation between input and out­put. Separate connections for the photodiode bias and output-transistor collector increase the speed up to a hundred times that of a conven­tional phototransistor coupler by reduc­ing the base-collector capacitance. • High speed: 1 Mb/s These single channel optocoup­ lers are available in 8-Pin DIP­, SO-8 and Widebody package configurations. The 6N135, HCPL-0500, and HCNW135 are for use in TTL/ CMOS, TTL/LSTTL or wide bandwidth analog applications. Current transfer ratio (CTR) for these devices is 7% minimum at IF = 16 mA. The 6N136, HCPL-2502, HCPL-0501, and HCNW136 are designed for high speed TTL/TTL applications. A standard 16 mA TTL sink current through the input LED will provide enough output current for 1 TTL load and a 5.6 kΩ pull-up resistor. CTR for these devices is 19% minimum at IF = 16 mA. Functional Diagram • TTL compatible • Available in 8-Pin DIP, SO-8, widebody packages • Open collector output • Safety approval UL Recognized – 3750 Vrms for 1 minute (5000 Vrms for 1 minute for HCNW and Option 020 devices) per UL1577 CSA Approved IEC/EN/DIN EN 60747-5-5 Approved – VIORM = 567 V peak for SO-8 devices – VIORM = 630 V peak for DIP 300 mil devices – VIORM = 1414 V peak for DIP 400 mil (widebody) devices • Dual channel version available (253X/053X/0534) Applications • High voltage insulation • Video signal isolation • Line receivers • Feedback element in switched mode power supplies NC 1 8 V CC ANODE 2 7 VB 3 6 VO CATHODE NC 4 TRUTH TABLE (POSITIVE LOGIC) LED VO ON LOW OFF HIGH • High speed logic ground isolation – TTL/TTL, TTL/CMOS, TTL/LSTTL • Replaces pulse transformers • Replaces slow phototransistor isolators • Analog signal ground isolation 5 GND A 0.1 µF bypass capacitor must be connected between pins 5 and 8. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Schematic ANODE 8 IO 6 VCC IF 2 + VF CATHODE I CC - VO 3 5 SHIELD GND IB 7 VB Selection Guide    Minimum CMR       Current dV/dt VCM Transfer (V/µs) (V) Ratio (%) 1,000 10 7 19 15 8-Pin DIP      Small-Outline Widebody (300 Mil) SO-8 (400 Mil) Single Dual Single Dual Single Channel Channel Channel Channel Channel Package Package* Package Package* Package 6N135 HCPL-2530 HCPL-0530 HCNW135 6N136 HCPL-2531 HCPL-0501 HCPL-0531 HCNW136 HCPL-2502 *Technical data for these products are on separate Avago publications. 2 HCPL-0500 Ordering Information 6N135, 6N136, HCPL-2502, HCPL-0500, HCPL-0501 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW135, HCNW136 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All these devices are approved under CSA Component Acceptance Notice #5, File CA 88324. Option Part number 6N135 6N136 HCPL-2502 HCPL-0500 HCPL-0501 HCNW135 HCNW136 RoHS Compliant Non RoHS Compliant -000E No option -300E #300 X X -500E #500 X X -020E #020 -320E #320 -520E #520 -060E #060 -360E #360 X X -560E #560 X X -000E No option -500E #500 -060E #060 -560E #560 -000E No option -300E #300 -500E #500 Package Surface Mount Gull Wing Tape & Reel UL 5000 Vrms/ 1 Minute rating IEC/EN/DIN EN 60747-5-5 Quantity 50 per tube 300mil DIP-8 X X X X 50 per tube X X 1000 per reel X 50 per tube X 50 per tube X 1000 per reel X X 50 per tube X 50 per tube X 1000 per reel 100 per tube SO-8 400 mil Widebody DIP-8 X X X X X X X X X X X 1500 per reel X 100 per tube X 1500 per reel X X 42 per tube X X 42 per tube X X 750 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-2502-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: HCPL-2502 to order product of 300 mil DIP package in tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use ‘-XXXE‘. 3 Package Outline Drawings 8-Pin DIP Package (6N135/6, HCPL-2502) 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) 8 TYPE NUMBER 7 6 A XXXXZ YYWW EEE 1 2 5 6.35 ± 0.25 (0.250 ± 0.010) OPTION CODE* DATE CODE RU 3 4 UL RECOGNITION LOT ID 1.78 (0.070) MAX. 1.19 (0.047) MAX. 5 ° TYP. 3.56 ± 0.13 (0.140 ± 0.005) 0.254 + 0.076 - 0.051 + 0.003) (0.010 - 0.002) 4.70 (0.185) MAX. 0.51 (0.020) MIN. 2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES). *MARKING CODE LETTER FOR OPTION NUMBERS "L" = OPTION 020 "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. 0.65 (0.025) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2.54 ± 0.25 (0.100 ± 0.010) NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N135/6) LAND PATTERN RECOMMENDATION 9.65 ± 0.25 (0.380 ± 0.010) 8 7 6 1.016 (0.040) 5 6.350 ± 0.25 (0.250 ± 0.010) 10.9 (0.430) 1 2 3 4 1.27 (0.050) 1.19 (0.047) MAX. 9.65 ± 0.25 (0.380 ± 0.010) 1.780 (0.070) MAX. 7.62 ± 0.25 (0.300 ± 0.010) 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) 0.635 ± 0.130 (0.025 ± 0.005) NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 4 + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 0.635 ± 0.25 (0.025 ± 0.010) 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 2.0 (0.080) 12 ° NOM. Small Outline SO-8 Package (HCPL-0500/1) LAND PATTERN RECOMMENDATION 8 7 5 XXX YWW EEE 3.937 ± 0.127 (0.155 ± 0.005) PIN ONE 6 1 2 3 5.994 ± 0.203 (0.236 ± 0.008) TYPE NUMBER (LAST 3 DIGITS) DATE CODE LOT ID 4 0.406 ± 0.076 (0.016 ± 0.003) 1.9 (0.075) 1.270 BSC (0.050) 0.64 (0.025) * 5.080 ± 0.127 (0.200 ± 0.005) 7° 3.175 ± 0.127 (0.125 ± 0.005) * 7.49 (0.295) 45 ° X 0.432 (0.017) 0~7 ° 1.524 (0.060) 0.228 ± 0.025 (0.009 ± 0.001) 0.203 ± 0.102 (0.008 ± 0.004) TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± 0.254 (0.205 ± 0.010) 0.305 MIN. (0.012) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. 8-Pin Widebody DIP Package (HCNW135/6) 11.00 MAX. (0.433) 11.23 ± 0.15 (0.442 ± 0.006) 8 7 6 9.00 ± 0.15 (0.354 ± 0.006) 5 TYPE NUMBER A HCNWXXXX YYWW EEE DATE CODE LOT ID 1 2 3 4 10.16 (0.400) TYP. 1.55 (0.061) MAX. 7 ° TYP. + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) 5.10 MAX. (0.201) 3.10 (0.122) 3.90 (0.154) 2.54 (0.100) TYP. 1.8 ± 0.15 (0.071 ± 0.006) 5 0.51 (0.021) MIN. DIMENSIONS IN MILLIMETERS (INCHES). 0.40 (0.016) 0.56 (0.022) NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW135/6) 11.23 ± 0.15 (0.442 ± 0.006) 8 7 6 LAND PATTERN RECOMMENDATION 5 9.00 ± 0.15 (0.354 ± 0.006) 1 2 3 13.56 (0.534) 4 2.29 (0.09) 1.3 (0.051) 12.30 ± 0.30 (0.484 ± 0.012) 1.55 (0.061) MAX. 11.00 MAX. (0.433) + 0.003) 4.00 MAX. (0.158) 1.80 ± 0.15 (0.071 ± 0.006) 2.54 (0.100) BSC 0.75 ± 0.25 (0.030 ± 0.010) + 0.076 0.254 - 0.0051 (0.010 - 0.002) 1.00 ± 0.15 (0.039 ± 0.006) 7 ° NOM. DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. Solder Reflow Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used. Regulatory Information The devices contained in this data sheet have been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-5 (HCNW and Option 060/360/560 only) 6 Insulation and Safety Related Specifications 8-Pin DIP (300 Mil) Value SO-8 Value Widebody (400 Mil) Value Units Conditions Parameter Symbol Minimum External Air Gap (External Clearance) L(101) 7.1 4.9 9.6 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (External Creepage) L(102) 7.4 4.8 10.0 mm Measured from input terminals to output terminals, shortest distance path along body. Minimum Internal Plastic Gap (Internal Clearance) 0.08 0.08 1.0 mm Through insulation distance, conductor to conductor, usually the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Minimum Internal Tracking (Internal Creepage) NA NA 4.0 mm Measured from input terminals to output terminals, along internal cavity. 200 200 200 Volts DIN IEC 112/VDE 0303 Part 1 IIIa IIIa IIIa Tracking Resistance (Comparative Tracking Index) Isolation Group CTI Option 300 - surface mount classification is Class A in accordance with CECC 00802. 7 Material Group (DIN VDE 0110, 1/89, Table 1) IEC/EN/DIN EN 60747-5-5 Insulation Characteristics (OPTION 060 ONLY)* Description 8 Pin DIP SO-8 Installation classification per DIN VDE 0110, Table 1 for rated mains voltage ≤ 150 Vrms for rated mains voltage ≤ 300 Vrms for rated mains voltage ≤ 600 Vrms Symbol I – IV I – IV I – IV I – IV I – IV I – III Climatic Classification 0/70/21 0/70/21 Pollution Degree (DIN VDE 0110/39) 2 2 Unit Maximum Working Insulation Voltage VIORM 630 567 Vpeak Input to Output Test Voltage, Method b* VIORM × 1.875 = VPR, 100% Production Test with tm=1 sec, Partial discharge < 5 pC VPR 1181 1063 Vpeak Input to Output Test Voltage, Method a* VIORM × 1.6 = VPR, Type and Sample Test, tm=10 sec, Partial discharge < 5 pC VPR 1008 907 Vpeak Highest Allowable Overvoltage* (Transient Overvoltage tini = 60 sec) VIOTM 8000 6000 Vpeak Safety-limiting values – maximum values allowed in the event of a failure Case Temperature Input Current Output Power TS IS, INPUT PS, OUTPUT 175 230 600 150 150 600 °C mA mW Insulation Resistance at TS, VIO = 500 V RS ≥ 109 ≥ 109 Ω * Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application. IEC/EN/DIN EN 60747-5-5 Insulation Characteristics (HCNW135/6 OPTION 060 ONLY)* Description Symbol Characteristic Installation classification per DIN VDE 0110, Table 1 for rated mains voltage ≤ 150 Vrms for rated mains voltage ≤ 300 Vrms for rated mains voltage ≤ 600 Vrms for rated mains voltage ≤ 1000 Vrms I – IV I – IV I – IV I – III Climatic Classification 0/70/21 Pollution Degree (DIN VDE 0110/39) Unit 2 Maximum Working Insulation Voltage VIORM 1414 Vpeak Input to Output Test Voltage, Method b* VIORM × 1.875 = VPR, 100% Production Test with tm=1 sec, Partial discharge < 5 pC VPR 2651 Vpeak Input to Output Test Voltage, Method a* VIORM × 1.6 = VPR, Type and Sample Test, tm=10 sec, Partial discharge < 5 pC VPR 2262 Vpeak Highest Allowable Overvoltage* (Transient Overvoltage tini = 60 sec) VIOTM 8000 Vpeak Safety-limiting values – maximum values allowed in the event of a failure Case Temperature Input Current Output Power TS IS, INPUT PS, OUTPUT 150 400 700 °C mA mW Insulation Resistance at TS, VIO = 500 V RS ≥ 109 Ω * Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application. 8 Absolute Maximum Ratings Parameter Symbol Storage Temperature* TS Operating Temperature* TA Average Forward Input Current* IF(AVG) Peak Forward Input Current*   (50% duty cycle, 1 ms pulse width)   (50% duty cycle, 1 ms pulse width) IF(PEAK) Peak Transient Input Current*    (≤1 µs pulse width, 300 pps) IF(TRANS) Reverse LED Input Voltage* (Pin 3-2)   VR Input Power Dissipation*   PIN Average Output Current* (Pin 6) IO(AVG) 8 mA Peak Output Current* IO(PEAK) 16 mA Emitter-Base Reverse Voltage* (Pin 5-7) VEBR 5 V Supply Voltage (Pin 8-5) VCC -0.5 30 V Output Voltage (Pin 6-5) VO -0.5 20 V Supply Voltage* (Pin 8-5) VCC -0.5 15 V Output Voltage* (Pin 6-5) VO -0.5 15 V Base Current* (Pin 7) IB 5 mA Output Power Dissipation* PO Lead Solder Temperature* (Through-Hole Parts Only)   1.6 mm below seating plane, 10 seconds   up to seating plane, 10 seconds TLS Reflow Temperature Profile TRP *Data has been registered with JEDEC for the 6N135/6N136. 9 Device Min. Max. Units -55 125 °C 8-Pin DIP SO-8 -55 100 °C Widebody -55 85 Note 25 mA 1 8-Pin DIP SO-8 50 mA 2 Widebody 40 8-Pin DIP SO-8 1 Widebody 0.1 8-Pin DIP SO-8 5 Widebody 3 8-Pin DIP SO-8 45 Widebody 40 A V mW 100 mW 8-Pin DIP 260 °C Widebody 260 °C SO-8 and Option 300 See Package Outline Drawings section 3 4 Electrical Specifications (DC) Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. See note 13. Parameter Current Transfer Ratio Logic Low Output Voltage Symbol Device Min. Typ.** Max. Units CTR* 6N135 HCPL-0500 HCNW135 HCPL-2502 7 5 18 19 50 % 15 15 19 15 25 24 25 0.1 0.1 0.4 0.5 0.1 0.1 0.4 0.5 µA µA VOL 6N136 HCPL-0501 HCNW136 6N135 HCPL-0500 HCNW135 6N136 HCPL-2502 HCPL-0501 HCNW136 TA = 25°C VO = 0.4 V VO = 0.5 V 22 TA = 25°C 50 TA = 25°C VO = 0.4 V VO = 0.5 V VO = 0.4 V VO = 0.5 V Logic High Output Current IOH* 0.003 0.01 Logic Low Supply Current Logic High Supply Current ICCL 50 0.5 1 50 200 ICCH* 0.02 1 Input Forward VF* Voltage Input Reverse Breakdown Voltage BVR* Temperature Coefficient of Forward Voltage Input Capacitance ∆VF/ ∆TA Transistor DC Current Gain hFE CIN *For JEDEC registered parts. **All typicals at TA = 25°C. 10 8-Pin DIP SO-8 Widebody 8-Pin DIP SO-8 Widebody 1.5 1.45 1.35 5 1.68 2 1.7 1.8 1.85 1.95 V µA V 8-Pin DIP SO-8 Widebody -1.6 8-Pin DIP SO-8 Widebody 8-Pin DIP SO-8 Widebody 60 TA = 25°C IO = 1.1 mA IO = 0.8 mA TA = 25°C IO = 3.0 mA IO = 2.4 mA TA = 25°C TA = 25°C VO = VCC = 5.5 V VO = VCC = 15 V VO = VCC = 15 V IF = 16 mA, VO = Open, VCC = 15 V TA = 25°C IF = 0 mA, VO = Open, VCC = 15 V TA = 25°C IF = 16 mA TA = 25°C V 3 Test Conditions IF = 16 mA IR = 10 µA IR = 100 µA mV/°C IF = 16 mA -1.9 90 150 130 180 160 pF f = 1 MHz, VF = 0 V VO = 5 V, IO = 3 mA VO = 0.4 V, IB = 20 µA VO = 0.4 V, IB = 20 µA VO = 5 V, IO = 3 mA IF = 16 mA, VCC = 4.5 V Fig. Note 1, 2, 4 5, 11 IF = 16 mA, VCC = 4.5 V IF = 0 mA 7 13 13 3 Switching Specifications (AC) Over recommended temperature (TA = 0°C to 70°C), VCC = 5 V, IF = 16 mA unless otherwise specified. Parameter Sym. Device Min. Typ.** Max. Units      Test Conditions Fig. Note Propagation tPHL* 6N135 0.2 1.5 µs TA = 25°C RL = 4.1 kΩ 5, 6, 8, 9 Delay Time to HCPL-0500 2.0 11 Logic Low at HCNW135 Output 6N136 0.2 0.8 TA = 25°C RL = 1.9 kΩ HCPL-2502 HCPL-0501 HCNW136 1.0 Propagation tPLH* 6N135 1.3 1.5 µs TA = 25°C RL = 4.1 kΩ 5, 6, 8, 9 Delay Time to HCPL-0500 2.0 11 Logic High at HCNW135 Output 6N136 0.6 0.8 TA = 25°C RL = 1.9 kΩ HCPL-2502 HCPL-0501 HCNW136 1.0 Common Mode |CMH| 6N135 1 kV/µs RL = 4.1 kΩ IF = 0 mA, TA = 25°C, 12 7, 8, Transient Im HCPL-0500 1 VCM = 10 Vp-p 9 munity at Logic HCNW135 CL = 15 pF High Level 6N136 1 R = 1.9 kΩ Output L HCPL-2502 1 HCPL-0501 Common Mode |CML| 6N135 1 kV/µs RL = 4.1 kΩ IF = 16 mA, TA = 25°C, 12 7, 8, Transient Im HCPL-0500 1 VCM = 10 Vp-p 9 munity at Logic HCNW135 CL = 15 pF Low Level 6N136 1 RL = 1.9 kΩ Output HCPL-2502 1 HCPL-0501 Bandwidth BW 6N135/6 9 MHz See Test Circuit 8, 10 10 HCPL-2502 HCPL-0500/1 HCNW135/6 11 *For JEDEC registered parts. **All typicals at TA = 25°C. 11 Package Characteristics Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. Parameter Sym. Device Min. Input-Output Momentary Withstand Voltage** VISO 8-Pin DIP SO-8 3750 Widebody 5000 8-Pin DIP (Option 020) 5000 Input-Output Resistance II-O 8-Pin DIP RI-O 8-Pin DIP SO-8 Widebody Typ.* Max. 1 1012 10 12 Units Test Conditions V rms RH < 50%, t = 1 min., TA = 25°C 6, 14 µA 45% RH, t = 5 s, VI-O = 3 kVdc, TA = 25°C 6, 16 Ω VI-O = 500 Vdc 6 10 10 CI-O Note 6, 15 6, 12, 15 TA = 25°C 13 TA = 100°C 11 Input-Output Capacitance Fig. 8-Pin DIP SO-8 0.6 Widebody 0.5 pF f = 1 MHz 6 0.6 * All typicals at TA = 25°C. ** The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203E. Notes:   1.  Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8).   2.  Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8).   3.  Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8).   4.  Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8).   5.  CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100.   6.  Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.   7.  Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM /dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V).   8.  The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.   9.  The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and 6.1 kΩ pull-up resistor. 10.  The frequency at which the ac output voltage is 3 dB below its mid-frequency value. 11.  The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Avago guarantees a minimum CTR of 19%. 12.  See Option 020 data sheet for more information. 13.  Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended. 14.  In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table if applicable. 15.  In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table if applicable. 16.  This rating is equally validated by an equivalent ac proof test. 12 T = 25° C 10 VA = 5.0 V CC 35 mA 30 mA 25 mA 5 20 mA 15 mA 10 mA 0 IF = 5 mA 0 10 WIDEBODY 16 40 mA IO Ð OUTPUT CURRENT Ð mA IO Ð OUTPUT CURRENT - mA 8 PIN DIP, SO-8 40 mA 12 35 mA 30 mA 25 mA 8 20 mA 15 mA 4 10 mA IF = 5 mA 0 20 TA = 25° C VCC = 5.0 V 0 10 VO - OUTPUT VOLTAGE - V 20 VO - OUTPUT VOLTAGE - V 8 PIN DIP, SO-8 1.5 6N135, HCPL-0500 6N136, HCPL-2502 HCPL-0501 1.0 0.5 0.1 NORMALIZED I F = 16 mA VO = 0.4 V VCC = 5 V TA = 25° C 0 1 10 100 NORMALIZED CURRENT TRANSFER RATIO NORMALIZED CURRENT TRANSFER RATIO Figure 1. DC and pulsed transfer characteristics. WIDEBODY 1.5 HCNW135/6 1.0 0.5 0 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 4.5 V TA = 25 ° C 0 1 IF - INPUT CURRENT - mA 10 100 IF - INPUT CURRENT - mA Figure 2. Current transfer ratio vs. input current. 8 PIN DIP, SO-8 100 IF TA = 25° C + VF - 10 1.0 1000 0.1 0.01 0.001 1.1 1.2 1.3 1.4 1.5 VF - FORWARD VOLTAGE - VOLTS Figure 3. Input current vs. forward voltage. 13 IF - FORWARD CURRENT - mA IF - FORWARD CURRENT - mA 1000 1.6 WIDEBODY TA = 25° C 100 10 1.0 IF 0.1 + VF - 0.01 0.001 1.2 1.3 1.4 1.5 1.6 1.7 1.8 VF - FORWARD VOLTAGE - VOLTS 1.0 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25° C 0.9 0.8 6N135, HCPL-0500 6N136, HCPL-2502, HCPL-0501 0.7 0.6 -60 -40 -20 0 20 40 80 100 60 NORMALIZED CURRENT TRANSFER RATIO NORMALIZED CURRENT TRANSFER RATIO 8 PIN DIP, SO-8 1.1 WIDEBODY 1.1 1.0 HCNW135/6 0.9 0.8 0.7 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25° C 0.6 0.5 0.4 -60 -40 -20 TA - TEMPERATURE - ° C 0 40 20 80 100 60 TA - TEMPERATURE - ° C Figure 4. Current transfer ratio vs. temperature. tp - PROPAGATION DELAY - ns IF = 16 mA, VCC = 5.0 V 6N135, HCPL-0500 (RL = 4.1 kΩ) 6N136, HCPL-0501, HCPL-2502 (RL = 1.9 kΩ) 1500 1000 tPLH tPHL 500 0 -60 20 -20 60 WIDEBODY 1000 tp - PROPAGATION DELAY - ns 8 PIN DIP, SO-8 2000 IF = 16 mA, VCC = 5.0 V HCNW135 (RL = 4.1 kΩ) HCNW136 (RL = 1.9 kΩ) 800 600 t PLH 200 0 -60 -40 -20 100 t PHL 400 0 20 40 60 80 100 TA - TEMPERATURE - ° C TA - TEMPERATURE - ° C Figure 5. Propagation delay vs. temperature. 2.0 1.0 0.8 0.6 8 PIN DIP, SO-8 I F = 10 mA I F = 16 mA VCC = 5.0 V TA = 25° C tPLH 0.4 t PHL 0.2 0.1 1 2 3 4 5 6 7 8 9 10 RL - LOAD RESISTANCE - (kΩ) Figure 6. Propagation delay time vs. load resistance. 14 WIDEBODY 10.0 tP - PROPAGATION DELAY - µs tP - PROPAGATION DELAY - µs 3.0 I F = 10 mA I t = 16 mA 6.0 4.0 VCC = 5.0 V TA = 25° C t PLH 1.0 0.6 t PHL 0.4 0.2 0.1 1 2 4 10 40 RL - LOAD RESISTANCE - (kΩ) 100 IF = 0 VO = VCC = 5.0 V 10+3 +2 10 10+1 100 10 -1 10 -2 -75 -50 -25 0 +25 +50 +75 +100 IOH - LOGIC HIGH OUTPUT CURRENT - nA IOH - LOGIC HIGH OUTPUT CURRENT - nA 8 PIN DIP, SO-8 10+4 WIDEBODY +3 10 IF = 0 VO = VCC = 15 V +2 10 +1 10 0 10 -60 -40 -20 0 20 40 60 80 100 TA - TEMPERATURE - ° C TA - TEMPERATURE - ° C 8 PIN DIP, SO-8 0.30 IO I F - SMALL SIGNAL CURRENT TRANSFER RATIO IO I F - SMALL SIGNAL CURRENT TRANSFER RATIO Figure 7. Logic high output current vs. temperature. WIDEBODY 0.50 TA = 25° C, RL = 100 Ω, VCC = 5 V TA = 25° C, RL = 100 Ω, VCC = 5 V 0.40 0.20 0.30 0.20 0.10 0.10 0 0 4 8 12 16 20 25 IF - QUIESCENT INPUT CURRENT - mA 0 0 4 8 12 16 20 25 IF - QUIESCENT INPUT CURRENT - mA 8-PIN DIP/S0-8 800 PS (mW) IS (mA) For 8-PIN DIP IS (mA) For S0-8 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 200 TS - CASE TEMPERATURE - ° C OUTPUT POWER - PS, INPUT CURRENT - IS OUTPUT POWER - PS, INPUT CURRENT - IS Figure 8. Small-signal current transfer ratio vs. quiescent input current. HCNW135/6 1000 PS (mW) 900 IS (mA) 800 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 TS - CASE TEMPERATURE - ° C Figure 9. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-5. 15 6N135/6, HCPL-0500/1, HCPL-2502 NORMALIZED RESPONSE - dB +5 TA = 25°C 6N135/6, HCPL-0500/1, HCPL-2502 +12 V 1 0.1 µF +12 V 8 2.1 KΩ 0 2 7 3 6 15 KΩ 1.2 KΩ 9.1 KΩ -5 47 µF 100 Ω VFF -10 Q1 22 Ω 1N4150 -20 0.1 1.0 10 5 TRIM FOR UNITY GAIN 470Ω � 100 Ω RT 51 Ω -15 Q 1 , Q 2 , Q 3 : 2N3904 TYPICAL LINEARITY = ± 3% AT V IN = 1 V p-p TYPICAL SNR = 50dB TYPICAL R T = 375 Ω TYPICAL VO dc = 3.8 V TYPICAL I F = 9 mA 100 f - FREQUENCY - MHz HCNW135/6 HCNW135/6 Figure 10. Frequency response IF 0 5V VO 1.5 V PULSE GEN. ZO = 50 Ω t r = 5 ns 10% DUTY CYCLE 1/f < 100 µS 1.5 V VOL 1 8 2 7 3 6 +5 V RL 0.1µF I F MONITOR RM t PLH t PHL IF 4 5 1 8 2 7 3 6 VO CL = 1.5 µF Figure 11. Switching test circuit IF VCM 0V 10% 90% 90% tr +5 V B 10% tf RL A VO 5V SWITCH AT A: I F = 0 mA VO SWITCH AT B: I F = 16 mA VFF VOL VO 0.1 µF 4 5 VCM + - PULSE GEN. Figure 12. Test circuit for transient immunity and typical waveforms For product information and a complete list of distributors, please go to our website: VO Q2 0.1 µF 4 1 KΩ 0.1 µF Q3 www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2014 Avago Technologies. All rights reserved. Obsoletes AV01-0550EN AV02-0171EN - July 14, 2014 (1 MΩ 12 pF TEST INPUT)