0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
HCPL-063L-560

HCPL-063L-560

  • 厂商:

    AVAGO(博通)

  • 封装:

    SO-8_5.08X3.937MM

  • 描述:

    OPTOISO 3.75KV 2CH OPEN COLL 8SO

  • 数据手册
  • 价格&库存
HCPL-063L-560 数据手册
Data Sheet HCPL-260L/060L/263L/063L High-Speed LVTTL-Compatible 3.3V Optocouplers Description The Broadcom® HCPL-260L/060L/263L/063L are optically coupled gates that combine a GaAsP light-emitting diode and an integrated high gain photo detector. An enable input allows the detector to be strobed. The output of the detector IC is an open collector Schottky-clamped transistor. The internal shield provides a guaranteed common mode transient immunity specification of 15 kV/µs at 3.3V. Features       3.3V/5V dual-supply voltages Low power consumption 15 kV/µs minimum Common Mode Rejection (CMR) at VCM = 1000V High speed: 15 MBd typical LVTTL/LVCMOS compatible Low input current capability: 5 mA Guaranteed AC and DC performance over temperature: –40°C to +85°C Available in 8-pin DIP, SOIC-8 Strobable output (single-channel products only) Safety approvals: UL, CSA, IEC/EN/DIN EN 60747-5-5 This unique design provides maximum AC and DC circuit isolation while achieving LVTTL/LVCMOS compatibility. The optocoupler AC and DC operational parameters are guaranteed from –40°C to +85°C allowing trouble-free system performance.  These optocouplers are suitable for high-speed logic interfacing, input/output buffering, as line receivers in environments that conventional line receivers cannot tolerate and are recommended for use in extremely high ground or induced noise environments. Applications             Isolated line receiver Computer-peripheral interfaces Microprocessor system interfaces Digital isolation for A/D, D/A conversion Switching power supply Instrument input/output isolation Ground loop elimination Pulse transformer replacement Field buses CAUTION! Take normal static precautions in handling and assembly of this component to prevent damage, degradation, or both that may be induced by ESD. The components featured in this data sheet are not to be used in military or aerospace applications or environments. Broadcom AV02-0616EN March 1, 2021 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Functional Diagram HCPL-260L/060L HCPL-263L/063L 8 V CC NC 1 ANODE 1 1 8 V CC ANODE 2 7 VE CATHODE 1 2 7 V O1 CATHODE 3 6 VO CATHODE 2 3 6 V O2 NC 4 5 GND SHIELD ANODE 2 4 SHIELD 5 GND Truth Table (Positive Logic) Truth Table (Positive Logic) LED Enable Output LED Output ON H L ON L OFF H H OFF H ON L H OFF L H ON NC L OFF NC H Broadcom AV02-0616EN 2 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Ordering Information HCPL-xxxx is UL Recognized with 3750 Vrms for 1 minute per UL1577. Option Part Number HCPL-260L HCPL-263L HCPL-060L HCPL-063L RoHS Compliant -000E Non-RoHS Compliant Package No option -300E -300 -500E #500 -020E -020 -320E 300-mil DIP-8 Surface Gull Mount Wing X X X -320 X X -520E -520 X X -060E #060 #560 -000E No option -300E #300 -500E #500 -020E #020 -320E X 300-mil DIP-8 X X X X -320 X X -520E #520 X X -060E -060 -560E -560 No option IEC/EN/DIN EN 60747-5-5 50 per tube X X 1000 per reel X 50 per tube X 50 per tube X X 1000 per reel X 50 per tube X 1000 per reel 50 per tube X X 1000 per reel X 50 per tube X 50 per tube X 1000 per reel X X SO-8 X X X X -500E #500 X -060E #060 X -560E -560 -000E No option X -500E #500 X -060E -060 X -560E -560 X SO-8 Quantity 50 per tube X -000E UL 5000 Vrms/1 Minute Rating 50 per tube X -560E Tape and Reel 50 per tube 1000 per reel 100 per tube X 1500 per reel X X X X 100 per tube 1500 per reel 100 per tube X X 1500 per reel X 100 per tube X 1500 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Combination of Option 020 and Option 060 is not available. Example 1: HCPL-260L-560E to order product of 300-mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: HCPL-263L to order product of 300-mil DIP package in tube packaging and non-RoHS compliant. Option data sheets are available. Contact your Broadcom o sales representative or authorized distributor for information. Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since July 15, 2001 and RoHS compliant option will use ‘-XXXE’. Broadcom AV02-0616EN 3 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Schematic HCPL-260L/060L IF 2+ VF HCPL-263L/063L ICC IO – 3 SHIELD IE VE 8 6 5 7 VCC VO 1 + IF1 ICC IO1 VF1 GND – 2 IO2 VF2 + 4 7 VCC VO1 SHIELD 3 – USE OF A 0.1 PF BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 5). 8 IF2 6 5 SHIELD VO2 GND Package Outline Drawings 8-Pin DIP Package 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) 8 AVAGO LEAD-FREE DATE CODE PIN 1 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) • 1 7 6.35 ± 0.25 (0.250 ± 0.010) 6 5 A NNNN Z YYWW EEE P 2 3 DEVICE PART NUMBER TEST RATING CODE UL LOGO 4 SPECIAL PROGRAM CODE LOT ID 1.78 (0.070) MAX. Broadcom + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 4.70 (0.185) MAX. 0.51 (0.020) MIN. 2.92 (0.115) MIN. 1.080 ± 0.320 (0.043 ± 0.013) 5° TYP. 0.65 (0.025) MAX. 2.54 ± 0.25 (0.100 ± 0.010) DIMENSIONS IN MILLIMETERS (INCHES). *MARKING CODE LETTER FOR OPTION NUMBERS "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. AV02-0616EN 4 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers 8-Pin DIP Package with Gull Wing Surface Mount in Option 500 (HCPL-260L, HCPL-263L) LAND PATTERN RECOMMENDATION 9.65 ± 0.25 (0.380 ± 0.010) 8 7 6 1.016 (0.040) 5 6.350 ± 0.25 (0.250 ± 0.010) 1 2 3 4 1.780 (0.070) MAX. 1.19 (0.047) MAX. 10.9 (0.430) 3.56 ± 0.13 (0.140 ± 0.005) 1.27 (0.050) 9.65 ± 0.25 (0.380 ± 0.010) 7.62 ± 0.25 (0.300 ± 0.010) 1.080 ± 0.320 (0.043 ± 0.013) 2.54 (0.100) BSC 0.635 ± 0.130 DIMENSIONS IN MILLIMETERS (INCHES). (0.025 ± 0.005) LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. Broadcom 2.0 (0.080) 0.635 ± 0.25 (0.025 ± 0.010) + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 12° NOM. AV02-0616EN 5 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Small Outline SO-8 Package 3.937 ± 0.127 (0.155 ± 0.005) DEVICE PART NUMBER LEAD-FREE 8 7 6 5 NNNN Z YYWW EEE • PIN 1 1 2 3 TEST RATING CODE DATE CODE LOT ID 4 0.406 ± 0.076 (0.016 ± 0.003) 5.994 ± 0.203 (0.236 ± 0.008) 1.270 BSC (0.050) * 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.125 ± 0.005) 7° 1.524 (0.060) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± 0.254 (0.205 ± 0.010) 0.432 45° X (0.017) 0 ~ 7° 0.228 ± 0.025 (0.009 ± 0.001) 0.203 ± 0.102 (0.008 ± 0.004) 0.305 MIN. (0.012) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. OPTION NUMBER 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. Reflow Soldering Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-halide flux should be used. Regulatory Information The HCPL-260L/060L/263L/063L have been approved by the following organizations. UL Approval under UL 1577, Component Recognition Program, File E55361. CSA Approval under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-5 Broadcom AV02-0616EN 6 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Insulation and Safety Related Specifications Symbol 8-Pin DIP (300 Mil) Value SO-8 Value Units Minimum External Air Gap (External Clearance) L (101) 7.1 4.9 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (External Creepage) L (102) 7.4 4.8 mm Measured from input terminals to output terminals, shortest distance path along body. 0.08 0.08 mm Through insulation distance, conductor to conductor, usually the direct distance between the photoemitter and photodetector inside the optocoupler cavity. 200 200 V IIIa IIIa Parameter Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) CTI Isolation Group Conditions DIN IEC 112/VDE 0303 Part 1 Material Group (DIN VDE 0110, 1/89, Table 1) IEC/EN/DIN EN 60747-5-5 Insulation Characteristicsa Description Symbol PDIP SO-8 Option 060 Option 060 Units Installation classification per DIN VDE 0110, Table 1 For rated mains voltage ≤ 150 Vrms I-IV I-IV For rated mains voltage ≤ 300 Vrms I-IV I-IV For rated mains voltage ≤ 600 Vrms I-III I-III 40/85/21 40/85/21 2 2 Climatic Classification Pollution Degree (DIN VDE 0110/39) Maximum Working Insulation Voltage VIORM 630 567 Vpeak Input to Output Test Voltage, Method b VIORM × 1.875 = VPR, 100% Production Test with tm=1s, Partial discharge < 5 pC VPR 1181 1063 Vpeak Input to Output Test Voltage, Method aa VIORM × 1.6 = VPR, Type and Sample Test, tm=10s, Partial discharge < 5 pC VPR 1008 907 Vpeak VIOTM 6000 6000 Vpeak TS 175 150 °C Input Current IS, INPUT 230 150 mA Output Power PS, OUTPUT 600 600 mW RS ≥ 109 ≥ 109 Ω a Highest Allowable Overvoltage (Transient Overvoltage tini = 60s) Safety-Limiting Values – maximum values allowed in the event of a failure. Case Temperature Insulation Resistance at TS, VIO = 500V a. Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for a detailed description. NOTE: Broadcom Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. AV02-0616EN 7 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Thermal Derating Curve Figures OUTPUT POWER – PS, INPUT CURRENT – IS OUTPUT POWER – PS, INPUT CURRENT – IS HCPL-060L/HCPL-063L 800 PS (mW) IS (mA) 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 TS – CASE TEMPERATURE – qC 175 200 HCPL-260L/HCPL-263L 800 PS (mW) IS (mA) 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 TS – CASE TEMPERATURE – qC 175 200 ° Absolute Maximum Ratings (No Derating Required up to 85°C) Parameter Packagea Symbol Min. Max. Units Storage Temperature TS –55 125 °C Operating Temperature TA –40 85 °C Average Forward Input Current IF Single 8-Pin DIP Single SO-8 — 20 mA Dual 8-Pin DIP Dual SO-8 — 15 8-Pin DIP, SO-8 — 5 V VR Input Power Dissipation PI — 40 mW VCC — 7 V — VCC + 0.5 V Single 8-Pin DIP Single SO-8 b c, d Reverse Input Voltage Supply Voltage (1 Minute Maximum) Note c Enable Input Voltage (Not to Exceed VCC by more than 500 mV) VE Enable Input Current IE — 5 mA Output Collector Current IO — 50 mA c Output Collector Voltage VO — 7 V c Output Collector Power Dissipation PO Single 8-Pin DIP Single SO-8 — 85 mW Dual 8-Pin DIP Dual SO-8 — 60 c, e a. Ratings apply to all devices except otherwise noted in the Package column. b. Peaking circuits may produce transient input currents up to 50 mA, 50-ns maximum pulse width, provided average current does not exceed 20 mA. c. Each channel. d. Peaking circuits may produce transient input currents up to 50 mA, 50-ns maximum pulse width, provided average current does not exceed 15 mA. e. Derate linearly above +80°C free-air temperature at a rate of 2.7 mW/°C for the SOIC-8 package. Broadcom AV02-0616EN 8 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Recommended Operating Conditions Parameter Symbol Min. Max. Units Input Current, Low Level IFLa 0 250 µA Input Current, High Levelb IFHc 5 15 mA Power Supply Voltage VCC 2.7 3.6 V 4.5 5.5 Low Level Enable Voltage VEL 0 0.8 V High Level Enable Voltage VEH 2.0 VCC V Operating Temperature TA –40 85 °C Fan Out (at RL = 1 kΩ)b N — 5 TTL Loads Output Pull-up Resistor RL 330 4k Ω a. The off condition can also be guaranteed by ensuring that VFL ≤ 0.8V. b. Each channel. c. The initial switching threshold is 5 mA or less. It is recommended that 6.3 mA to 10 mA be used for best performance and to permit at least a 20% LED degradation guardband. Broadcom AV02-0616EN 9 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Electrical Specifications Over recommended operating conditions (TA = –40°C to +85°C, 2.7V ≤ VCC ≤ 3.6V), unless otherwise specified. All Typicals at VCC = 3.3V, TA = 25°C. All enable test conditions apply to single-channel products only. NOTE: Bypassing of the power supply line is required, with a 0.1-µF ceramic disc capacitor adjacent to each optocoupler as illustrated in Figure 11. Total lead length between both ends of the capacitor and the isolator pins should not exceed 20 mm. Parameter Symbol High Level Output Current Input Threshold Current Min. Typ. Max. Units IOHa — 4.5 50 µA ITH — 3.0 5.0 Low Level Output Voltage VOLa — 0.35 High Level Supply Current ICCH Single — Dual Low Level Supply Current ICCL Device Test Conditions Figure Note VCC = 3.3V, VE = 2.0V, VO = 3.3V, IF = 250 µA 1 b, c mA VCC = 3.3V, VE = 2.0V, VO = 0.6 V, IOL (Sinking) = 13 mA 2 c 0.6 V VCC = 3.3V, VE = 2.0V, IF = 5 mA, IOL (Sinking) = 13 mA 3 c 4.7 7.0 mA — 6.9 10.0 Single — 7.0 10.0 Dual — 8.7 15.0 VE = 0.5V, IF = 0 mA VCC = 3.3V mA VE = 0.5V, IF = 10 mA VCC = 3.3V High Level Enable Current IEH Single — –0.5 –1.2 mA VCC = 3.3V, VE = 2.0V Low Level Enable Current IELa Single — –0.5 –1.2 mA VCC = 3.3V, VE = 0.5V High Level Enable Voltage VEH Single 2.0 — — V Low Level Enable Voltage VEL Single — — 0.8 Input Forward Voltage VF 1.4 1.5 1.75 V TA = 25°C, IF = 10 mA Input Reverse Breakdown Voltage BVRa 5 — — V IR = 10 µA b Input Diode Temperature Coefficient VF/TA — –1.6 — mV°C IF = 10 mA b CIN — 60 — Input Capacitance c V a pF 5 b f = 1 MHz, VF = 0V b a. The JEDEC Registration specifies 0°C to +70°C. Broadcom specifies –40°C to +85°C. b. Each channel. c. No external pull-up is required for a high logic state on the enable input. If the VE pin is not used, tying VE to VCC will result in improved CMR performance. For single channel products only. See Application Information. Broadcom AV02-0616EN 10 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Electrical Specifications (DC) Over recommended operating conditions (TA = –40°C to +85°C, 4.5V ≤ VCC ≤ 5.5V), unless otherwise specified. All typicals at VCC = 5V, TA = 25°C. Parameter Symbol High Level Output Current IOH Input Threshold Current ITH Low Level Output Voltage VOL High Level Supply Current ICCH Low Level Supply Current ICCL Min. Typ.a Max. Units — 5.5 100 µA Single — 2.0 5.0 Dual — 2.5 — — 0.35 — Channel Single Test Conditions Figure Note VCC = 5.5V, VO = 5.5V, IFL = 250 µA 1 b, c mA VCC = 5.5V, VO = 0.6V, IOL > 13 mA 2 c 0.6 V VCC = 5.5V, IF = 5 mA, IOL (Sinking) = 13 mA 3 c 7.0 10.0 mA VE = 0.5V, VCC = 5.5V, IF = 0 mA 6.5 — VE = VCC, VCC = 5.5V, IF = 0 mA VCC = 5.5V, IF = 0 mA Dual — 10.0 15.0 Single — 9.0 13.0 — 8.5 — VE = VCC, VCC = 5.5V, IF = 10 mA Dual — 13.0 21.0 VCC = 5.5V, IF = 10 mA mA VE = 0.5V, VCC = 5.5V, IF = 10 mA High Level Enable Current IEH Single — –0.7 –1.6 mA VCC = 5.5V, VE = 2.0V Low Level Enable Current IEL Single — –0.9 –1.6 mA VCC = 5.5V, VE = 0.5V High Level Enable Voltage VEH Single 2.0 — — V Low Level Enable Voltage VEL Single — — 0.8 V Input Forward Voltage VF 1.4 1.5 1.75 V TA = 25°C, IF = 10 mA 1.8 V IF =10 mA V IR = 10 µA b mV/°C IF = 10 mA b 1.3 Input Reverse Breakdown Voltage BVR 5 — — Input Diode Temperature Coefficient VF/TA — –1.6 — CIN — 60 — Input Capacitance pF c d f = 1 MHz, VF = 0V b a. The JEDEC Registration specifies 0°C to +70°C. Broadcom specifies –40°C to +85°C. b. Each channel. c. No external pull-up is required for a high logic state on the enable input. If the VE pin is not used, tying VE to VCC will result in improved CMR performance. For single-channel products only. See Application Information. d. Bypassing of the power supply line is required, with a 0.1-µF ceramic disc capacitor adjacent to each optocoupler as illustrated in Figure 11. Total lead length between both ends of the capacitor and the isolator pins should not exceed 20 mm. Broadcom AV02-0616EN 11 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Switching Specifications Over recommended operating conditions (TA = –40°C to +85°C, 2.7V ≤ VCC ≤ 3.6V), IF = 7.5 mA, unless otherwise specified. All Typicals at TA = 25°C, VCC = 3.3V. Parameter Symbol Min. Typ. Max. Units Propagation Delay Time to High Output Level tPLH — — 90 ns RL = 350Ω, CL = 15 pF Propagation Delay Time to Low Output Level tPHL — — 75 ns RL = 350Ω, CL = 15 pF |tPHL – tPLH| — — 25 ns RL = 350Ω, CL = 15 pF tPSK — — 40 ns RL = 350Ω, CL = 15 pF c, e, f Output Rise Time (10% to 90%) tr — 45 — ns RL = 350Ω, CL = 15 pF a, c Output Fall Time (90% to 10%) tf — 20 — ns RL = 350Ω, CL = 15 pF a, c Propagation Delay Time of Enable from VEH to VEL tELH — 45 — ns RL = 350Ω, CL = 15 pF, VEL = 0V, VEH = 3V 9 g Propagation Delay Time of Enable from VEL to VEH tEHL — 30 — ns RL = 350Ω, CL = 15 pF, VEL = 0V, VEH = 3V 9 h Pulse Width Distortion Propagation Delay Skew Test Conditions Figure Note 6, 7 a, b, c a, c, d 8 c, e a. Each channel. b. The tPLH propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5V point on the rising edge of the output pulse. c. No external pull up is required for a high logic state on the enable input. If the VE pin is not used, tying VE to VCC will result in improved CMR performance. For single channel products only. See Application Information. d. The tPHL propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5V point on the falling edge of the output pulse. e. See Figure 9 for measurement details. f. tPSK is equal to the worst case difference in tPHL, tPLH, or both that will be seen between units at any given temperature and specified test conditions. g. The tELH enable propagation delay is measured from the 1.5V point on the falling edge of the enable input pulse to the 1.5V point on the rising edge of the output pulse. h. The tEHL enable propagation delay is measured from the 1.5V point on the rising edge of the enable input pulse to the 1.5V point on the falling edge of the output pulse. Broadcom AV02-0616EN 12 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Switching Specifications (AC) Over recommended operating conditions TA = –40°C to 85°C, 4.5V ≤ VCC ≤ 5.5V, IF = 7.5 mA, unless otherwise specified. All Typicals at VCC = 5V, TA = 25°C. Parameter Symbol Min. Typ. Max. Units Propagation Delay Time to High Output Level tPLH 20 48 75 ns TA = 25°C, — — 100 Propagation Delay Time to Low Output Level tPHL 25 50 75 ns TA = 25°C, — — 100 |tPHL – tPLH| — 3.5 35 ns RL = 350Ω, CL = 15 pF TPSK — — 40 ns RL = 350Ω, CL = 15 pF c, e, f Output Rise Time (10% to 90%) tr — 24 — ns RL = 350Ω, CL = 15 pF a, c Output Fall Time (10% to 90%) tf — 10 — ns RL = 350Ω, CL = 15 pF a, c Propagation Delay Time of Enable from VEH to VEL tELH — 30 — ns RL = 350Ω, CL = 15 pF, VEL = 0V, VEH =3 V 9 g Propagation Delay Time of Enable from VEL to VEH tEHL — 20 — ns RL = 350Ω, CL = 15 pF, VEL = 0V, VEH =3V 9 h Pulse Width Distortion Propagation Delay Skew Test Conditions Figure Note RL = 350Ω, CL = 15 pF 6, 7 a, b c , RL = 350Ω, CL = 15 pF 6, 7 a, c, d 8 c, e a. Each channel. b. The tPLH propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5V point on the rising edge of the output pulse. c. No external pull-up is required for a high logic state on the enable input. If the VE pin is not used, tying VE to VCC will result in improved CMR performance. For single-channel products only. See Application Information. d. The tPHL propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5V point on the falling edge of the output pulse. e. See test circuit for measurement details. f. tPSK is equal to the worst case difference in tPHL, tPLH, or both that will be seen between units at any given temperature and specified test conditions. g. The tELH enable propagation delay is measured from the 1.5V point on the falling edge of the enable input pulse to the 1.5V point on the rising edge of the output pulse. h. The tEHL enable propagation delay is measured from the 1.5V point on the rising edge of the enable input pulse to the 1.5V point on the falling edge of the output pulse. Broadcom AV02-0616EN 13 HCPL-260L/060L/263L/063L Data Sheet Parameter High-Speed LVTTL-Compatible 3.3V Optocouplers Symbol Device Min. Typ. Output High Level Common Mode Transient Immunity |CMH| HCPL-263L HCPL-063L HCPL-260L HCPL-060L 15 25 Output Low Level Common Mode Transient Immunity |CML| HCPL-263L HCPL-063L HCPL-260L HCPL-060L 15 Output High Level Common Mode Transient Immunity |CMH| HCPL-263L HCPL-063L HCPL-260L HCPL-060L Output Low Level Common Mode Transient Immunity |CML| HCPL-263L HCPL-063L HCPL-260L HCPL-060L Units Test Conditions Figure Note kV/µs VCC = 3.3V, IF = 0 mA, VO(MIN) = 2V, RL = 350Ω, TA = 25°C, VCM = 1000V and VCM = 10V 10 a, b, c 25 kV/µs VCC = 3.3V, IF = 7.5 mA, VO(MAX) = 0.8V, RL = 350Ω, TA = 25°C, VCM = 1000V and VCM = 10V 10 b, c, d 10 15 kV/µs VCC = 5V, IF = 0 mA, VO(MIN) = 2V, RL = 350 Ω, TA = 25°C, VCM = 1000V 10 a, b, c 10 15 kV/µs VCC = 5V, IF = 7.5 mA, VO(MAX) = 0.8V, RL = 350Ω, TA = 25°C, VCM = 1000V 10 b, c, d a. CMH is the maximum tolerable rate of rise on the common mode voltage to assure that the output will remain in a high logic state (that is, VO > 2.0V). b. For sinusoidal voltages, (|dVCM | / dt)max = fCMVCM (p-p). c. No external pull-up is required for a high logic state on the enable input. If the VE pin is not used, tying VE to VCC will result in improved CMR performance. For single-channel products only. See Application Information. d. CML is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state (that is, VO < 0.8V). Broadcom AV02-0616EN 14 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Package Characteristics All Typicals at TA = 25°C. Parameter Sym. Package Min. Typ. Max. Units Input-Output Insulation II-Oa Single 8-Pin DIP Single SO-8 — — 1 µA Input-Output Momentary Withstand Voltaged VISO 8-Pin DIP SO-8 3750 — — Vrms Input-Output Resistance RI-O 8-Pin SO-8 — 1012 — Ω VI-O = 500 Vdc b, e, f Input-Output Capacitance CI-O 8-Pin DIP SO-8 — 0.6 — pF f = 1 MHz, TA = 25°C b, e, f RH ≤ 45%, t = 5s, VI-I = 500V Input-Input Insulation Leakage Current II-I Dual Channel — 0.005 — µA Resistance (Input-Input) RI-I Dual Channel — 1011 — Ω Capacitance (Input-Input) CI-I Dual 8-Pin Dip — 0.03 — pG Dual SO-8 — 0.25 — Test Conditions Figure Note 45% RH, t = 5s, VI-O = 3 kV DC, TA = 25°C b, c RH ≤ 50%, TA = 25°C, t = 1 minute b, c g g f = 1 MHz g a. The JEDEC Registration specifies 0°C to +70°C. Broadcom specifies –40°C to +85°C. b. The device is considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together. c. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 Vrms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table, if applicable. d. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating, refer to the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table (if applicable), your equipment level safety specification, or Broadcom Application Note 1074, Optocoupler Input-Output Endurance Voltage. e. Each channel. f. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together. For dual-channel products only. g. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. For dual-channel products only. Broadcom AV02-0616EN 15 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers IOH – HIGH LEVEL OUTPUT CURRENT – PA 15 VCC = 3.3 V VO = 3.3 V VE = 2.0 V* IF = 250 PA * FOR SINGLE CHANNEL PRODUCTS ONLY 10 5 0 -60 -40 -20 60 0 40 20 TA – TEMPERATURE – qC 80 100 IOH – HIGH LEVEL OUTPUT CURRENT – PA Figure 1: Typical High Level Output Current vs. Temperature 15 VCC = 5.5 V VO = 5.5 V VE = 2.0 V* IF = 250 PA * FOR SINGLE CHANNEL PRODUCTS ONLY 10 5 0 -60 -20 -40 20 60 0 40 TA – TEMPERATURE – qC 80 100 ITH – INPUT THRESHOLD CURRENT – mA 12 10 8-PIN DIP, SO-8 VCC = 3.3 V VO = 0.6 V 8 RL = 350 : 6 RL = 1 k: 4 2 0 -60 RL = 4 k: -40 -20 0 20 40 60 TA – TEMPERATURE – qC 80 100 ITH – INPUT THRESHOLD CURRENT – mA Figure 2: Typical Output Voltage vs. Forward Input Current 6 5 8-PIN DIP, SO-8 VCC = 5.0 V VO = 0.6 V 4 RL = 350 : 3 RL = 1 k: 2 1 0 -60 RL = 4 k: -40 -20 0 20 40 60 TA – TEMPERATURE – qC 80 100 VOL – LOW LEVEL OUTPUT VOLTAGE – V 0.8 0.7 0.6 8-PIN DIP, SO-8 VCC = 3.3 V VE = 2.0 V* IF = 5.0 mA * FOR SINGLE CHANNEL PRODUCTS ONLY 0.5 0.4 IO = 13 mA 0.3 0.2 0.1 0 -60 Broadcom -40 -20 0 20 40 60 TA – TEMPERATURE – qC 80 100 VOL – LOW LEVEL OUTPUT VOLTAGE – V Figure 3: Typical Low Level Output Voltage vs. Temperature 0.8 0.7 0.6 8-PIN DIP, SO-8 VCC = 5.5 V VE = 2.0 V* IF = 5.0 mA 0.5 IO = 16 mA 0.4 0.3 IO = 9.6 mA 0.2 0.1 0 -60 * FOR SINGLE CHANNEL PRODUCTS ONLY -40 -20 IO = 12.8 mA IO = 6.4 mA 0 20 40 60 TA – TEMPERATURE – qC 80 100 AV02-0616EN 16 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Figure 4: Typical Low Level Output Current vs. Temperature VCC = 3.3 V VE = 2.0 V* VOL = 0.6 V 60 70 * FOR SINGLE CHANNEL PRODUCTS ONLY IOL – LOW LEVEL OUTPUT CURRENT – mA IOL – LOW LEVEL OUTPUT CURRENT – mA 70 50 IF = 5.0 mA 40 20 -60 -40 -20 0 20 40 60 TA – TEMPERATURE – qC 80 100 60 VCC = 5.0 V VE = 2.0 V* VOL = 0.6 V * FOR SINGLE CHANNEL PRODUCTS ONLY IF = 10 – 15 mA 50 IF = 5.0 mA 40 20 -60 -40 -20 0 20 40 60 TA – TEMPERATURE – qC 80 100 Figure 5: Typical Input Diode Forward Characteristic 8-PIN DIP, SO-8 IF – FORWARD CURRENT – mA 1000 100 IF + 10 VF – 1.0 TA = 25 qC 0.1 0.01 0.001 1.1 1.2 1.3 1.4 1.5 1.6 VF – FORWARD VOLTAGE – V Broadcom AV02-0616EN 17 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Figure 6: Test Circuit for tPHL and tPLH 3.3 V or 5 V SINGLE CHANNEL VCC 8 1 PULSE GEN. IF ZO = 50 : tf = tr = 5 ns INPUT MONITORING NODE R M 2 7 3 6 4 GND 5 PULSE GEN. ZO = 50 : tf = tr = 5 ns IF 0.1 PF BYPASS RL OUTPUT VO MONITORING NODE *CL INPUT MONITORING NODE RM 1 DUAL CHANNEL VCC 8 2 7 3 6 4 GND 5 3.3 V or 5 V RL 0.1 PF BYPASS OUTPUT VO MONITORING NODE CL* *CL IS APPROXIMATELY 15 pF WHICH INCLUDES PROBE AND STRAY WIRING CAPACITANCE. IF = 7.50 mA INPUT IF = 3.75 mA IF tPHL tPLH OUTPUT VO 1.5 V Figure 7: Typical Propagation Delay vs. Temperature 150 80 tP - PROPAGATION DELAY - ns 120 tP – PROPAGATION DELAY – ns 100 VCC = 3.3 V IF = 7.5 mA tPLH , RL = 350 : 90 tPHL , RL = 350 : 1 k: 4 k: 60 tPHL , RL = 350 : 0 -60 -40 -20 20 60 0 20 40 TA – TEMPERATURE – qC 80 0 -60 100 tPLH , RL = 4 k: tPLH , RL = 1 k: 40 60 30 VCC = 5.0 V IF = 7.5 mA tPLH , RL = 350 : -40 -20 0 20 40 60 TA – TEMPERATURE – qC 80 100 Figure 8: Typical Pulse Width Distortion vs. Temperature 40 VCC = 3.3 V IF = 7.5 mA 40 PWD- PULSE WIDTH DISTORTION - ns PWD – PULSE WIDTH DISTORTION – ns 50 30 RL = 350 : 20 10 0 -60 Broadcom -40 -20 0 20 40 60 TA – TEMPERATURE – qC 80 100 RL = 4 k: 30 VCC = 5.0 V IF = 7.5 mA 20 RL = 350 : 10 0 -10 -60 RL = 1 k: -40 -20 0 20 40 60 TA – TEMPERATURE – qC 80 100 AV02-0616EN 18 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Figure 9: Test Circuit for tEHL and tELH PULSE GEN. ZO = 50: tf = tr = 5 ns INPUT VE MONITORING NODE 3.3 V or 5 V 7.5 mA IF 1 VCC 8 2 7 3 6 4 GND 5 0.1 PF BYPASS RL *CL 3.0 V 1.5 V INPUT VE OUTPUT VO MONITORING NODE tEHL tELH OUTPUT VO 1.5 V *CL IS APPROXIMATELY 15 pF WHICH INCLUDES PROBE AND STRAY WIRING CAPACITANCE. Figure 10: Test Circuit for Common Mode Transient Immunity and Typical Waveforms IF SINGLE CHANNEL IF B A VFF 1 VCC 8 2 7 3 6 4 GND 5 VCM + – PULSE GENERATOR ZO = 50 : VCM VO VO Broadcom 3.3 V or 5 V 0.1 PF BYPASS RL OUTPUT VO MONITORING NODE DUAL CHANNEL B A VFF VCC 8 2 7 3 6 4 GND 5 RL 0.1 PF BYPASS 3.3 V or 5 V OUTPUT VO MONITORING NODE VCM + – PULSE GENERATOR ZO = 50 : VCM (PEAK) 0V 5 V SWITCH AT A: IF = 0 mA VO (MIN.) SWITCH AT B: IF = 7.5 mA VO (MAX.) 0.5 V 1 CMH CML AV02-0616EN 19 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Figure 11: Recommended Printed Circuit Board Layout GND BUS (BACK) VCC BUS (FRONT) NC ENABLE 0.1PF NC OUTPUT SINGLE CHANNEL DEVICE ILLUSTRATED. 10 mm MAX. (SEE NOTE 5) Figure 12: Recommended LVTTL Interface Circuit SINGLE CHANNEL DEVICE VCC1 3.3 V or 5V 3.3 V or 5V VCC2 8 220 : D1* IF + RL 2 6 VF – GND 1 3 SHIELD 1 0.1 PF BYPASS 5 VE 7 GND 2 2 *DIODE D1 (1N916 OR EQUIVALENT) IS NOT REQUIRED FOR UNITS WITH OPEN COLLECTOR OUTPUT. DUAL CHANNEL DEVICE CHANNEL 1 SHOWN VCC1 3.3 V or 5V 220 : D1* 1 Broadcom IF + RL 1 7 VF – GND 1 3.3 V or 5 V VCC2 8 2 SHIELD 5 0.1 PF BYPASS GND 2 2 AV02-0616EN 20 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Application Information Common-Mode Rejection for HCPL-260L Families Figure 13 shows the recommended drive circuit for optimal common-mode rejection performance. Note the following two points:   The enable pin is tied to VCC rather than floating (this applies to single-channel parts only). Two LED-current setting resistors are used instead of one. This is to balance ILED variation during commonmode transients. If the enable pin is left floating, it is possible for commonmode transients to couple to the enable pin, resulting in common-mode failure. This failure mechanism only occurs when the LED is on and the output is in the Low state. It is identified as occurring when the transient output voltage rises above 0.8V. Therefore, the enable pin should be connected to either VCC or logic-level high for best commonmode performance with the output low (CMRL). This failure mechanism is only present in single-channel parts that have the enable function. Also, common-mode transients can capacitively couple from the LED anode (or cathode) to the output-side ground causing current to be shunted away from the LED (which can be bad if the LED is on) or conversely cause current to be injected into the LED (bad if the LED is meant to be off). Figure 14 shows the parasitic capacitances that exist between LED anode/cathode and output ground (CLA and CLC). Also shown in Figure 14 on the input side is an AC-equivalent circuit. For transients occurring when the LED is on, common-mode rejection (CMRL, since the output is in the “low” state) depends upon the amount of LED current drive (IF). For conditions where IF is close to the switching threshold (ITH), CMRL also depends on the extent which ILP and ILN balance each other. In other words, any condition where commonmode transients cause a momentary decrease in IF will cause common-mode failure for transients that are fast enough. Figure 13: Recommended Drive Circuit for High-CMR * 1 VCC 220 : 220 : 74LS04 OR ANY TOTEM-POLE OUTPUT LOGIC GATE 8 VCC+ 0.01 PF 350 : 2 7 3 6 VO 5 GND 4 GND1 HCPL-260L * SHIELD GND2 * HIGHER CMR MAY BE OBTAINABLE BY CONNECTING PINS 1, 4 TO INPUT GROUND (GND1). Broadcom AV02-0616EN 21 HCPL-260L/060L/263L/063L Data Sheet High-Speed LVTTL-Compatible 3.3V Optocouplers Figure 14: AC Equivalent Circuit 1 1/2 RLED 1/2 RLED 8 2 3 4 Figure 15: TTL Interface Circuit ILN ILP 7 CLA + VCM 0.01 PF 420 : (MAX) 350 : 6 15 pF CLC SHIELD VCC VCC+ 5 VO GND 2N3906 (ANY PNP) 74L504 (ANY TTL/CMOS GATE) By using the circuit in Figure 13, good CMR can be achieved. The balanced ILED-setting resistors help equalize ILP and ILN to reduce the amount by which ILED is modulated from transient coupling through CLA and CLC.   Use of drive circuits where current is shunted from the LED in the LED “off” state (as shown in Figure 15 and Figure 16). This beneneficial for good CMRH. Use of IFH > 3.5 mA. This is good for high CMRL. Figure 15 shows a circuit that can be used with any totempole-output TTL/LSTTL/HCMOS logic gate. The buffer PNP transistor allows the circuit to be used with logic devices that have low current-sinking capability. It also helps maintain the driving-gate power-supply current at a constant level to minimize ground shifting for other devices connected to the input-supply ground. 2 LED 4 When using an open-collector TTL or open-drain CMOS logic gate, the circuit in Figure 16 may be used. When using a CMOS gate to drive the optocoupler, the circuit shown in Figure 17 may be used. The diode in parallel with the RLED speeds the turn-off of the optocoupler LED. Figure 16: TTL Open-Collector/Open-Drain Gate Drive Circuit VCC R CMR with Other Drive Circuits CMR performance with drive circuits other than that shown in Figure 13 may be enhanced by following these guidelines: HCPL-260L 3 – Likewise for common-mode transients that occur when the LED is off (that is, CMRH, since the output is “high”), if an imbalance between ILP and ILN results in a transient IF equal to or greater than the switching threshold of the optocoupler, the transient “signal” may cause the output to spike below 2V (which constitutes a CMRH failure). 1 1 HCPL-260L 2 74HC00 (OR ANY OPEN-COLLECTOR/ OPEN-DRAIN LOGIC GATE) 3 LED 4 Figure 17: CMOS Gate Drive Circuit VCC 1N4148 74HC04 (OR ANY TOTEM-POLE OUTPUT LOGIC GATE) 220 : 1 HCPL-260L 2 3 LED 4 Broadcom AV02-0616EN 22 Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, and the A logo are among the trademarks of Broadcom and/or its affiliates in the United States, certain other countries, and/or the EU. Copyright © 2014–2021 Broadcom. All Rights Reserved. The term “Broadcom” refers to Broadcom Inc. and/or its subsidiaries. For more information, please visit www.broadcom.com. Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does not assume any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others.
HCPL-063L-560 价格&库存

很抱歉,暂时无法提供与“HCPL-063L-560”相匹配的价格&库存,您可以联系我们找货

免费人工找货