HCPL-7800

Data Sheet HCPL-7800A/HCPL-7800 Isolation Amplifer Description The Broadcom® HCPL-7800A/HCPL-7800 (hereinafter referred to as HCPL-7800(A)), isolation amplifier family is designed for current sensing in electronic motor drives. In a typical implementation, motor currents flow through an external resistor and the resulting analog voltage drop is sensed by the HCPL-7800(A). A differential output voltage is created on the other side of the HCPL-7800(A) optical isolation barrier. This differential output voltage is proportional to the motor current and can be converted to a single-ended signal by using an op-amp as shown in the recommended application circuit. Because common-mode voltage swings of several hundred volts in tens of nanoseconds are common in modern switching inverter motor drives, the HCPL-7800(A) is designed to ignore very high common-mode transient slew rates (of at least 10 kV/µs). The high CMR capability of the HCPL-7800(A) isolation amplifier provides the precision and stability needed to accurately monitor motor current in high-noise motor control environments, providing for smoother control (less “torque ripple”) in various types of motor control applications. The product can also be used for general analog signal isolation applications requiring high accuracy, stability, and linearity under similarly severe noise conditions. For general applications, use the HCPL-7800 (gain tolerance of ± 3%). For precision applications, use the HCPL-7800A with part-to-part gain tolerance of ± 1%. The HCPL-7800(A) uses sigma-delta (-) analog-to-digital converter technology, chopper-stabilized amplifiers, and a fully differential circuit topology. Together, these features deliver unequaled isolation-mode noise rejection, as well as excellent offset and gain accuracy and stability over time and temperature. This performance is delivered in a compact, auto-insertable, industry standard 8-pin DIP package that meets worldwide regulatory safety standards. (A gull-wing surface mount option #300 is also available). Features          15 kV/µs common-mode rejection at VCM = 1000V Compact, auto-insertable standard 8-pin DIP package 0.00025-V/V/°C gain drift vs. temperature 0.3-mV input offset voltage 100-kHz bandwidth 0.004% nonlinearity Worldwide Safety Approval: UL 1577 (3750 Vrms/1 min.) and CSA, IEC/EN/DIN EN 60747-5-5 Advanced Sigma-Delta (-) A/D converter technology Fully differential circuit topology Applications      Motor phase and rail current sensing Inverter current sensing Switched mode power supply signal isolation General-purpose current sensing and monitoring General-purpose analog signal isolation CAUTION! Take normal static precautions when handling and assembling this component to prevent damage, degradation, or both, that may be induced by ESD. The components featured in this data sheet are not to be used in military or aerospace applications or environments. The components are not AEC-Q100 qualified and are not recommended for automotive applications. Broadcom AV02-0410EN November 19, 2020 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Functional Diagram VDD1 1 IDD1 IDD2 8 VDD2 VIN+ 2 + + 7 VOUT+ VIN- 3 - - 6 VOUT- GND1 4 NOTE: 5 GND2 SHIELD A 0.1-µF bypass capacitor must be connected between pins 1 and 4 and between pins 5 and 8. Ordering Information HCPL-7800A/HCPL-7800 is UL Recognized with 3750 Vrms for 1 minute per UL1577. Option Part Number HCPL-7800A HCPL-7800 RoHS Compliant Non-RoHS Compliant -000E No option -300E #300 -500E #500 Package 300 mil DIP-8 Surface Mount Gull Wing X X X X Tape and Reel X IEC/EN/DIN EN 60747-5-5 Quantity X 50 per tube X 50 per tube X 1000 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-7800A-500E to order product of Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: HCPL-7800 to order product of 300 mil DIP package in tube packaging and non-RoHS compliant. Option datasheets are available. Contact your Broadcom sales representative or authorized distributor for information. NOTE: Broadcom The notation “#XXX” is used for existing products, while products launched after July 15, 2001 and RoHS compliant option use “-XXXE”. AV02-0410EN 2 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Package Outline Drawings Standard DIP Package 9.80 ± 0.25 (0.386 ± 0.010) 8 7 6 DIMENSIONS IN MILLIMETERS AND (INCHES). 5 DATE CODE A 7800 NOTE: FLOATING LEAD PROTRUSION IS 0.5 mm (20 mils) MAX. YYWW 1 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 2 3 4 7.62 ± 0.25 (0.300 ± 0.010) 1.78 (0.070) MAX. 6.35 ± 0.25 (0.250 ± 0.010) 4.70 (0.185) MAX. 0.51 (0.020) MIN. 2.92 (0.115) MIN. 1.080 ± 0.320 (0.043 ± 0.013) NOTE: Broadcom 0.65 (0.025) MAX. 5° TYP. 0.20 (0.008) 0.33 (0.013) 2.54 ± 0.25 (0.100 ± 0.010) Initial or continued variation in the color of the HCPL-7800(A)’s white mold compound is normal and does not affect device performance or reliability. AV02-0410EN 3 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Gull Wing Surface Mount Option 300 LAND PATTERN RECOMMENDATION 9.80 ± 0.25 (0.386 ± 0.010) 8 6 7 1.016 (0.040) 5 A 7800 6.350 ± 0.25 (0.250 ± 0.010) YYWW 1 2 3 10.9 (0.430) 4 2.0 (0.080) 1.27 (0.050) 9.65 ± 0.25 (0.380 ± 0.010) 1.780 (0.070) MAX. 1.19 (0.047) MAX. 7.62 ± 0.25 (0.300 ± 0.010) 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) 0.635 ± 0.25 (0.025 ± 0.010) 0.635 ± 0.130 (0.025 ± 0.005) 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). TOLERANCES (UNLESS OTHERWISE SPECIFIED): xx.xx = 0.01 xx.xxx = 0.005 0.20 (0.008) 0.33 (0.013) 12° NOM. LEAD COPLANARITY MAXIMUM: 0.102 (0.004) NOTE: FLOATING LEAD PROTRUSION IS 0.5 mm (20 mils) MAX. Solder Reflow Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Use non-halide flux”. Regulatory Information The HCPL-7800(A) has been approved by the following organizations. IEC/EN/DIN EN 60747-5-5 UL Approved under UL 1577, component recognition program up to VISO = 3750 Vrms. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. Broadcom AV02-0410EN 4 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer IEC/EN/DIN EN 60747-5-5 Insulation Characteristics1 Description Symbol Characteristic Units Installation Classification per DIN VDE 0110/1.89, Table 1 For rated mains voltage 300 Vrms I-IV For rated mains voltage 600 Vrms II-III Climatic Classification 40/85/21 Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage 2 VIORM 891 VPEAK Input to Output Test Voltage, Method ba VIORM × 1.875 = VPR, 100% Production Test with tm = 1s, Partial discharge < 5 pC VPR 1670 VPEAK Input to Output Test Voltage, Method aa VIORM × 1.5 = VPR, Type and Sample Test, tm = 60s, Partial discharge < 5 pC VPR 1336 VPEAK VIOTM 6000 VPEAK TS 175 °C Input Powerb IS,INPUT 400 mA Ouput Powerb PS,OUTPUT 600 mW RS >109 Ω Highest Allowable Overvoltage (Transient Overvoltage tini = 10s) Safety-limiting values-maximum values allowed in the event of a failure. Case Temperature Input Currentb Insulation Resistance at TS, VIO = 500V a. Refer to the optocoupler section of the Isolation and Control Components Designer's Catalog, under Product Safety Regulations section, (IEC/EN/DIN EN 60747-5-5) for a detailed description of Method a and Method b partial discharge test profiles. b. See Figure 1 for dependence of PS and IS on ambient temperature. NOTE: These optocouplers are suitable for safe electrical isolation only within the safety limit data. Maintenance of the safety limit data is ensured by means of protective circuits. OUTPUT POWER Ð PS, INPUT CURRENT Ð IS Figure 1: Output Power vs. Case Temperature 800 PS (mW) 700 IS (mA) 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 200 TA Ð CASE TEMPERATURE Ð ¡C 1. Broadcom Insulation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits within the application. Surface Mount Classification is Class A in accordance with CECC00802. AV02-0410EN 5 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Insulation and Safety-Related Specifications Parameter Symbol Value Units Minimum External Air Gap (Clearance) L(101) 7.4 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (Creepage) L(102) 8.0 mm Measured from input terminals to output terminals, shortest distance path along the body. 0.5 mm Through insulation distance conductor to conductor, usually the straight line distance thickness between the emitter and the detector. >175 V Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) CTI Isolation Group III a Conditions DIN IEC 112/VDE 0303 Part 1 Material Group (DIN VDE 0110, 1/89, Table 1) Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS –55 125 °C Operating Temperature TA –40 100 Supply Voltage Steady-State Input Voltage VDD1, VDD2 0 5.5 VIN+, VIN– –2.0 VDD1 + 0.5 2-Second Transient Input Voltage Output Voltage Note V –6.0 VOUT –0.5 VDD2 + 0.5 Symbol Min. Max. Units TA –40 85 °C VDD1, VDD2 4.5 5.5 V Input Voltage (accurate and linear) VIN+, VIN– –200 200 mV Input Voltage (functional) VIN+, VIN– –2 2 V Recommended Operating Conditions Parameter Ambient Operating Temperature Supply Voltage Note a a. Broadcom recommends operation with VIN– = 0V (tied to GND1). Limiting VIN+ to 100 mV improves DC nonlinearity and nonlinearity drift. If VIN– is brought above VDD1 – 2V, an internal test mode may be activated. This test mode is for testing LED coupling and is not intended for customer use. NOTE: Broadcom For the following tables, Typical values represent the mean value of all characterization units at the nominal operating conditions. Typical drift specifications are determined by calculating the rate of change of the specified parameter versus the drift parameter (at nominal operating conditions) for each characterization unit, and then averaging the individual unit rates. The corresponding drift figures are normalized to the nominal operating conditions and show how much drift occurs as the particular drift parameter is varied from its nominal value, with all other parameters held at their nominal operating values. Note that the typical drift specifications in the following tables may differ from the slopes of the mean curves shown in the corresponding figures. AV02-0410EN 6 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer DC Electrical Specifications Unless otherwise noted, all typicals and figures are at the nominal operating conditions of VIN+ = 0V, VIN– = 0V, VDD1 = VDD2 = 5V and TA = 25°C; all Min./Max. specifications are within the recommended operating conditions. Parameter Symbol Min. Typ. Max. Units VOS –2.0 0.3 2.0 mV –3.0 — 3.0 |DVOS/DTA| — 3.0 10.0 µV/°C Gain (HCPL-7800A) G1 7.92 8.00 8.08 V/V Gain (HCPL-7800) G3 7.76 8.00 8.24 |DG/DTA| — 0.00025 — V/V/°C VOUT 200 mV Nonlinearity NL200 — 0.0037 0.35 % Magnitude of VOUT 200 mV Nonlinearity Change vs. Temperature |dNL200/dT| — 0.0002 — % / °C VOUT 100 mV Nonlinearity NL100 — 0.0027 0.2 % |VIN+|MAX — 308.0 — mV Input Supply Current IDD1 — 10.86 16.0 mA Output Supply Current IDD2 — 11.56 16.0 Input Current IIN+ — –0.5 5.0 µA |dIIN/dT| — 0.45 — nA/°C Output Low Voltage VOL — 1.29 — V Output High Voltage VOH — 3.80 — V Output Common-Mode Voltage VOCM 2.2 2.545 2.8 V Output Short-Circuit Current |IOSC| — 18.6 — mA Input Offset Voltage Magnitude of Input Offset Change vs. Temperature Magnitude of VOUT Gain Change vs.Temperature Maximum Input Voltage before VOUT Clipping Magnitude of Input Bias Current vs. Temperature Coefficient Equivalent Input Impedance Test Conditions TA = 25°C Figure Note 2, 3 –40°C < TA < +85°C, –4.5V < (VDD1, VDD2) < 5.5V –200 mV < VIN+ < 200 mV, TA = 25°C 4 a 5, 6, 7 b c –200 mV < VIN+ < 200 mV 8, 9 d –100 mV < VIN+ < 100 mV e 10 VIN+ = 400 mV 11 f VIN+ = –400 mV RIN — 500 — kΩ VOUT Output Resistance ROUT — 15 — Ω Input DC Common-Mode Rejection Ratio CMRRIN — 76 — dB g 12 h i j k a. This is the Absolute Value of Input Offset Change vs. Temperature. b. Gain is defined as the slope of the best-fit line of differential output voltage (VOUT+ – VOUT–) vs. differential input voltage (VIN+ – VIN–) over the specified input range. c. This is the Absolute Value of Gain Change vs. Temperature. d. Nonlinearity is defined as half of the peak-to-peak output deviation from the best-fit gain line, expressed as a percentage of the full-scale differential output voltage. e. NL100 is the nonlinearity specified over an input voltage range of ±100 mV. f. The input supply current decreases as the differential input voltage (VIN+ – VIN–) decreases. Broadcom AV02-0410EN 7 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer g. The maximum specified output supply current occurs when the differential input voltage (VIN+ – VIN–) = –200 mV, the maximum recommended operating input voltage. However, the output supply current will continue to rise for differential input voltages up to approximately –300 mV, beyond which the output supply current remains constant. h. Because of the switched-capacitor nature of the input sigma-delta converter, time-averaged values are shown. i. When the differential input signal exceeds approximately 308 mV, the outputs will limit at the typical values shown. j. Short circuit current is the amount of output current generated when either output is shorted to VDD2 or ground. k. CMRR is defined as the ratio of the differential signal gain (signal applied differentially between pins 2 and 3) to the common-mode gain (input pins tied together and the signal applied to both inputs at the same time), expressed in dB. AC Electrical Specifications Unless otherwise noted, all typicals and figures are at the nominal operating conditions of VIN+ = 0V, VIN– = 0V, VDD1 = VDD2 = 5V and TA = 25°C; all Min./Max. specifications are within the recommended operating conditions. Parameter Symbol Min. Typ. Max. Units BW 50 100 — kHz VOUT Noise NOUT — 31.5 — mVrms VIN to VOUT Signal Delay (50% to 10%) tPD10 — 2.03 3.3 µs VIN to VOUT Signal Delay (50% to 50%) tPD50 — 3.47 5.6 VIN to VOUT Signal Delay (50% to 90%) tPD90 — 4.99 9.9 tR/F — 2.96 6.6 Common-Mode Transient Immunity CMTI 10.0 15.0 — kV/µs Power Supply Rejection PSR — 170 — mVrms VOUT Bandwidth (–3 dB) Sine Wave VOUT Rise/ Fall Time (10% to 90%) Test Conditions VIN+ = 200 mVpk-pk Figure Note 13, 14 VIN+ = 0.0V VIN+ = 0 mV to 150-mV step. Measured at the output of MC34081 on Figure 16. VCM = 1 kV, TA = 25°C a 15, 16 17 b With recommended application circuit. c a. Output noise comes from two primary sources: chopper noise and sigma-delta quantization noise. Chopper noise results from chopper stabilization of the output op-amps. It occurs at a specific frequency (typically 400 kHz at room temperature), and is not attenuated by the internal output filter. A filter circuit can be easily added to the external post-amplifier to reduce the total rms output noise. The internal output filter does eliminate most, but not all, of the sigma-delta quantization noise. The magnitude of the output quantization noise is very small at lower frequencies (below 10 kHz) and increases with increasing frequency. b. CMTI (Common-Mode Transient Immunity or CMR, Common-Mode Rejection) is tested by applying an exponentially rising/falling voltage step on pin 4 (GND1) with respect to pin 5 (GND2). The rise time of the test waveform is set to approximately 50 ns. The amplitude of the step is adjusted until the differential output (VOUT+ – VOUT-) exhibits more than a 200-mV deviation from the average output voltage for more than 1 µs. The HCPL-7800(A) will continue to function if more than 10 kV/µs common-mode slopes are applied, as long as the breakdown voltage limitations are observed. c. The data sheet value is the differential amplitude of the transient at the output of the HCPL-7800(A) when a 1 Vpk-pk, 1-MHz square wave with 40-ns rise and fall times is applied to both VDD1 and VDD2. Broadcom AV02-0410EN 8 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Package Characteristics Parameter Symbol Min. Typ. Max. Units Test Condition Fig. Note Input-Output Momentary Withstand Voltage VISO 3750 — — Vrms Resistance (Input-Output) RI-O — >109 — Ω VI-O = 500 VDC c Capacitance (Input-Output) CI-O — 1.2 — pF ƒ = 1 MHz c RH < 50%, t = 1 minute, TA = 25°C a b , a. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 Vrms for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (method b) shown in IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table. b. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating, refer to the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table and your equipment level safety specification. c. This is a two-terminal measurement: pins 1–4 are shorted together and pins 5–8 are shorted together. Figure 2: Input Offset Voltage Test Circuit VDD1 VDD2 +15 V 0.1 μF 1 8 0.1 μF 2 7 10 kΩ + HCPL-7800 0.1 μF 3 6 4 5 10 kΩ 0.47 μF VOUT - AD624CD GAIN = 100 0.1 μF 0.47 μF -15 V Figure 4: Input Offset vs. Supply 0.8 0.39 0.7 0.38 VOS - INPUT OFFSET VOLTAGE - mV VOS - INPUT OFFSET VOLTAGE - mV Figure 3: Input Offset Voltage vs. Temperature 0.6 0.5 0.4 0.3 0.2 -55 -25 5 35 65 TA - TEMPERATURE - °C Broadcom 95 125 vs. VDD1 vs. VDD2 0.37 0.36 0.35 0.34 0.33 4.5 4.75 5.0 5.25 5.5 VDD - SUPPLY VOLTAGE - V AV02-0410EN 9 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Figure 5: Gain vs. Temperature 8.035 G - GAIN - V/V 8.03 8.025 8.02 8.015 8.01 -55 -35 -15 5 25 45 65 85 105 125 TA - TEMPERATURE - °C [ Figure 6: Gain and Nonlinearity Test Circuit VDD1 VDD2 +15 V +15 V 0.1 μF 1 8 0.1 μF VIN 404 0.1 μF 2 7 10 kΩ + HCPL-7800 13.2 0.1 μF 3 6 4 5 10 kΩ VOUT - AD624CD GAIN = 4 0.47 μF 0.1 μF 0.01 μF 0.47 μF + -15 V - AD624CD GAIN = 10 0.1 μF -15 V 10 kΩ 0.47 μF Broadcom AV02-0410EN 10 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Figure 7: Gain vs. Supply Figure 8: Nonlinearity vs. Temperature 8.032 0.03 0.025 NL - NONLINEARITY - % G - GAIN - V/V 8.03 8.028 vs. VDD1 8.026 vs. VDD2 8.024 4.5 4.75 5.0 0.02 0.015 0.01 0.005 5.25 0 -55 5.5 -25 VDD - SUPPLY VOLTAGE - V Figure 9: Nonlinearity vs. Supply 35 95 125 4.2 VO - OUTPUT VOLTAGE - V 0.004 0.003 vs. VDD1 3.4 2.6 1.8 VOP VOR vs. VDD2 0.002 4.5 4.75 5.0 5.25 1.0 -0.5 5.5 -0.3 -0.1 0.1 0.3 0.5 VIN - INPUT VOLTAGE - V VDD - SUPPLY VOLTAGE - V Figure 11: Supply Current vs. Input Voltage Figure 12: Input Current vs. Input Voltage 13 0 -1 IIN - INPUT CURRENT - μA IDD - SUPPLY CURRENT - mA 65 Figure 10: Output Voltage vs. Input Voltage 0.005 NL - NONLINEARITY - % 5 TA - TEMPERATURE - °C 10 7 IDD1 IDD2 4 -0.5 -0.3 -0.1 0.1 VIN - INPUT VOLTAGE - V Broadcom 0.3 -2 -3 -4 0.5 -5 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 VIN - INPUT VOLTAGE - V AV02-0410EN 11 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Figure 13: Gain vs. Frequency Figure 14: Phase vs. Frequency 50 1 0 -50 PHASE - DEGREES GAIN - dB 0 -1 -2 -100 -150 -200 -3 -4 -250 -300 10 1000 100 10000 100000 10 100 1000 10000 100000 FREQUENCY (Hz) FREQUENCY (Hz) [ Figure 15: Propagation Delay vs. Temperature PD - PROPAGATION DELAY - μS 5.5 4.7 Tpd 10 Tpd 50 Tpd 90 Trise 3.9 3.1 2.3 1.5 -55 -25 5 35 65 95 125 TA - TEMPERATURE - °C Broadcom AV02-0410EN 12 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Figure 16: Propagation Delay Test Circuits 10 kΩ VDD2 VDD1 +15 V 0.1 μF 8 1 0.1 μF 0.1 μF 2 kΩ 7 2 VIN HCPL-7800 0.01 μF 3 6 4 5 VOUT 2 kΩ + MC34081 0.1 μF 10 kΩ -15 V VIN IMPEDANCE LESS THAN 10 :. Figure 17: CMTI Test Circuits 10 kΩ 150 pF VDD2 78L05 +15 V IN OUT 0.1 μF 0.1 μF 0.1 μF 8 1 0.1 μF 2 kΩ 7 2 HCPL-7800 9V 3 6 4 5 2 kΩ MC34081 0.1 μF 10 kΩ 150 pF PULSE GEN. VOUT + -15 V - + VCM Broadcom AV02-0410EN 13 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Application Information Power Supplies and Bypassing The recommended supply connections are shown in Figure 18. A floating power supply (which in many applications could be the same supply that is used to drive the high-side power transistor) is regulated to 5V using a simple zener diode (D1); the value of resistor R4 should be chosen to supply sufficient current from the existing floating supply. The voltage from the current sensing resistor (Rsense) is applied to the input of the HCPL-7800(A) through an RC anti-aliasing filter (R2 and C2). Although the application circuit is relatively simple, a few recommendations should be followed to ensure optimal performance. The power supply for the HCPL-7800(A) is most often obtained from the same supply used to power the power transistor gate drive circuit. If a dedicated supply is required, in many cases it is possible to add an additional winding on an existing transformer. Otherwise, some sort of simple isolated supply can be used, such as a line powered transformer or a high-frequency DC-DC converter. An inexpensive 78L05 three-terminal regulator can also be used to reduce the floating supply voltage to 5V. To help attenuate high-frequency power supply noise or ripple, a resistor or inductor can be used in series with the input of the regulator to form a low-pass filter with the regulator’s input bypass capacitor. Figure 18: Recommended Supply and Sense Resistor Connections + HV+ GATE DRIVE CIRCUIT FLOATING POWER SUPPLY *** - D1 5.1 V C1 0.1 μF R2 39 Ω MOTOR *** C2 0.01 μF HCPL-7800 + R1 RSENSE *** HV- Broadcom AV02-0410EN 14 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer As shown in Figure 19, 0.1-µF bypass capacitors (C1, C2) should be located as close as possible to the pins of the HCPL-7800(A). The bypass capacitors are required because of the high-speed digital nature of the signals inside the HCPL-7800(A). A 0.01-µF bypass capacitor (C2) is also recommended at the input due to the switched-capacitor nature of the input circuit. The input bypass capacitor also forms part of the anti-aliasing filter, which is recommended to prevent high-frequency noise from aliasing down to lower frequencies and interfering with the input signal. The input filter also performs an important reliability function—it reduces transient spikes from ESD events flowing through the current sensing resistor. PC Board Layout The design of the printed circuit board (PCB) should follow good layout practices, such as keeping bypass capacitors close to the supply pins, keeping output signals away from input signals, the use of ground and power planes, etc. In addition, the layout of the PCB can also affect the isolation transient immunity (CMTI) of the HCPL-7800(A), due primarily to stray capacitive coupling between the input and the output circuits. To obtain optimal CMTI performance, the layout of the PC board should minimize any stray coupling by maintaining the maximum possible distance between the input and output sides of the circuit and ensuring that any ground or power plane on the PC board does not pass directly below or extend much wider than the body of the HCPL-7800(A). Figure 19: Recommended Application Circuit POSITIVE FLOATING SUPPLY HV+ C5 150 pF GATE DRIVE CIRCUIT R3 *** 10.0 kΩ U1 78L05 +5 V +15 V C8 0.1 μF IN OUT C1 C2 0.1 μF 0.1 μF R5 68 Ω 1 8 2 7 C4 0.1 μF C3 0.01 μF 2.00 kΩ U2 6 3 R1 R2 U3 + MC34081 VOUT 2.00 kΩ MOTOR *** + - 4 5 RSENSE HCPL-7800 C7 C6 150 pF R4 10.0 kΩ 0.1 μF -15 V *** HV- Broadcom AV02-0410EN 15 HCPL-7800A/HCPL-7800 Data Sheet Isolation Amplifer Figure 20: Example Printed Circuit Board Layout C2 R5 Figure 21: Motor Output Horsepower vs. Motor Phase Current and Supply C4 C3 TO VDD1 TO RSENSE+ TO RSENSE- TO VDD2 VOUT+ VOUT- Current Sensing Resistors The current sensing resistor should have low resistance (to minimize power dissipation), low inductance (to minimize di/dt induced voltage spikes which could adversely affect operation), and reasonable tolerance (to maintain overall circuit accuracy). Choosing a particular value for the resistor is usually a compromise between minimizing power dissipation and maximizing accuracy. Smaller sense resistance decreases power dissipation, while larger sense resistance can improve circuit accuracy by using the full input range of the HCPL-7800(A). The first step in selecting a sense resistor is determining how much current the resistor will be sensing. The graph in Figure 21 shows the RMS current in each phase of a three-phase induction motor as a function of average motor output power (in horsepower, hp) and motor drive supply voltage. The maximum value of the sense resistor is determined by the current being measured and the maximum recommended input voltage of the isolation amplifier. The maximum sense resistance can be calculated by taking the maximum recommended input voltage and dividing by the peak current that the sense resistor should see during normal operation. For example, if a motor will have a maximum RMS current of 10A and can experience up to 50% overloads during normal operation, the peak current is 21.1A (= 10 × 1.414 × 1.5). Assuming a maximum input voltage of 200 mV, the maximum value of sense resistance in this case would be about 10 mΩ. MOTOR OUTPUT POWER - HORSEPOWER 40 440 V 380 V 220 V 120 V 35 30 25 20 15 10 5 0 0 5 15 10 25 30 20 MOTOR PHASE CURRENT - A (rms) 35 The maximum average power dissipation in the sense resistor can also be easily calculated by multiplying the sense resistance times the square of the maximum RMS current, which is about 1W in the previous example. If the power dissipation in the sense resistor is too high, the resistance can be decreased below the maximum value to decrease power dissipation. The minimum value of the sense resistor is limited by precision and accuracy requirements of the design. As the resistance value is reduced, the output voltage across the resistor is also reduced, which means that the offset and noise, which are fixed, become a larger percentage of the signal amplitude. The selected value of the sense resistor will fall somewhere between the minimum and maximum values, depending on the particular requirements of a specific design. When sensing currents large enough to cause significant heating of the sense resistor, the temperature coefficient (tempco) of the resistor can introduce nonlinearity due to the signal dependent temperature rise of the resistor. The effect increases as the resistor-to-ambient thermal resistance increases. This effect can be minimized by reducing the thermal resistance of the current sensing resistor or by using a resistor with a lower tempco. Lowering the thermal resistance can be accomplished by repositioning the current sensing resistor on the PC board, by using larger PC board traces to carry away more heat, or by using a heat sink. For a two-terminal current sensing resistor, as the value of resistance decreases, the resistance of the leads become a significant percentage of the total resistance. This has two primary effects on resistor accuracy. First, the effective resistance of the sense resistor can become dependent on factors such as how long the leads are, how they are bent, Broadcom AV02-0410EN 16 HCPL-7800A/HCPL-7800 Data Sheet how far they are inserted into the board, and how far solder wicks up the leads during assembly (these issues will be discussed in more detail shortly). Second, the leads are typically made from a material, such as copper, which has a much higher tempco than the material from which the resistive element itself is made, resulting in a higher tempco overall. Both of these effects are eliminated when a four-terminal current sensing resistor is used. A four-terminal resistor has two additional terminals that are Kelvin-connected directly across the resistive element itself; these two terminals are used to monitor the voltage across the resistive element while the other two terminals are used to carry the load current. Because of the Kelvin connection, any voltage drops across the leads carrying the load current should have no impact on the measured voltage. When laying out a PC board for the current sensing resistors, a couple of points should be kept in mind. The Kelvin connections to the resistor should be brought together under the body of the resistor and then run very close to each other to the input of the HCPL-7800(A); this minimizes the loop area of the connection and reduces the possibility of stray magnetic fields from interfering with the measured signal. If the sense resistor is not located on the same PC board as the HCPL-7800(A) circuit, a tightly twisted pair of wires can accomplish the same thing. Also, multiple layers of the PC board can be used to increase current carrying capacity. Numerous plated-through vias should surround each non-Kelvin terminal of the sense resistor to help distribute the current between the layers of the PC board. The PC board should use 2 or 4 oz. copper for the layers, resulting in a current carrying capacity in excess of 20A. Making the current carrying traces on the PC board fairly large can also improve the sense resistor’s power dissipation capability by acting as a heat sink. Liberal use of vias where the load current enters and exits the PC board is also recommended. NOTE: Broadcom Refer to Broadcom Application Note 1078 for additional information on using Isolation Amplifiers. Isolation Amplifer Sense Resistor Connections The recommended method for connecting the HCPL-7800(A) to the current sensing resistor is shown in Figure 19. VIN+ (pin 2 of the HPCL-7800(A)) is connected to the positive terminal of the sense resistor, while VIN– (pin 3) is shorted to GND1 (pin 4), with the power-supply return path functioning as the sense line to the negative terminal of the current sense resistor. This allows a single pair of wires or PC board traces to connect the HCPL-7800(A) circuit to the sense resistor. By referencing the input circuit to the negative side of the sense resistor, any load current induced noise transients on the resistor are seen as a common-mode signal and will not interfere with the current-sense signal. This is important because the large load currents flowing through the motor drive, along with the parasitic inductances inherent in the wiring of the circuit, can generate both noise spikes and offsets that are relatively large compared to the small voltages that are being measured across the current sensing resistor. If the same power supply is used both for the gate drive circuit and for the current sensing circuit, it is very important that the connection from GND1 of the HCPL-7800(A) to the sense resistor be the only return path for supply current to the gate drive power supply to eliminate potential ground loop problems. The only direct connection between the HCPL-7800(A) circuit and the gate drive circuit should be the positive power supply line. Output Side The op-amp used in the external post-amplifier circuit should be of sufficiently high precision so that it does not contribute a significant amount of offset or offset drift relative to the contribution from the isolation amplifier. Generally, op-amps with bipolar input stages exhibit better offset performance than op-amps with JFET or MOSFET input stages. In addition, the op-amp should also have enough bandwidth and slew rate so that it does not adversely affect the response speed of the overall circuit. The post-amplifier circuit includes a pair of capacitors (C5 and C6) that form a single-pole low-pass filter; these capacitors allow the bandwidth of the post-amp to be adjusted independently of the gain and are useful for reducing the output noise from AV02-0410EN 17 HCPL-7800A/HCPL-7800 Data Sheet the isolation amplifier. Many different op-amps could be used in the circuit, including: MC34082A (Motorola), TLO32A, TLO52A, and TLC277 (Texas Instruments), LF412A (National Semiconductor). The gain-setting resistors in the post-amp should have a tolerance of 1% or better to ensure adequate CMRR and adequate gain tolerance for the overall circuit. Resistor networks can be used that have much better ratio tolerances than can be achieved using discrete resistors. A resistor network also reduces the total number of components for the circuit as well as the required board space. Frequently Asked Questions about the HCPL-7800(A) Basics 1. Why should I use the HCPL-7800(A) for sensing current when Hall-effect sensors are available that do not need an isolated supply voltage? Available in an auto-insertable, 8-pin DIP package, the HCPL-7800(A) is smaller than and has better linearity, offset vs. temperature and Common Mode Rejection (CMR) performance than most Hall-effect sensors. Additionally, the required input-side power supply can oftentimes be derived from the same supply that powers the gate-drive optocoupler. Sense Resistor and Input Filter 1. Where do I get 10-mΩ resistors? I have never seen one that low. Although less common than values above 10Ω, there are quite a few manufacturers of resistors suitable for measuring currents up to 50A when combined with the HCPL-7800(A). Example product information may be found at Dale's web site (http://www.vishay.com/vishay/ dale) and Isotek’s web site (http://www.isotekcorp.com). 2. Should I connect both inputs across the sense resistor instead of grounding VIN– directly to pin 4? Isolation Amplifer 3. Do I really need an RC filter on the input? What is it for? Are other values of R and C okay? The input anti-aliasing filter (R=39Ω, C=0.01 µF) shown in the typical application circuit is recommended for filtering fast-switching voltage transients from the input signal. (This helps to attenuate higher signal frequencies that could otherwise alias with the input sampling rate and cause higher input offset voltage.) Keep in mind some of the following issues when using different filter resistors or capacitors: – Filter resistor: Input bias current for pins 2 and 3: This is on the order of 500 nA. If you are using a single filter resistor in series with pin 2 but not pin 3, the IxR drop across this resistor adds to the offset error of the device. As long as this IR drop is small compared to the input offset voltage, there should not be a problem. If larger-valued resistors are used in series, it is better to put half of the resistance in series with pin 2 and half the resistance in series with pin 3. In this case, the offset voltage is due mainly to resistor mismatch (typically less than 1% of the resistance design value) multiplied by the input bias. – Filter resistor: The equivalent input resistance for HCPL-7800(A) is around 500 kΩ. It is best to ensure that the filter resistance is not a significant percentage of this value; otherwise, the offset voltage will be increased through the resistor divider effect. (As an example, if Rfilt = 5.5 kΩ, then VOS = (Vin × 1%) = 2 mV for a maximum 200 mV input and VOS will vary with respect to Vin.) – The input bandwidth is changed as a result of this different R-C filter configuration. In fact, this is one of the main reasons for changing the input-filter R-C time constant. – Filter capacitance: The input capacitance of the HCPL-7800(A) is approximately 1.5 pF. For proper operation, the switching input-side sampling capacitors must be charged from a relatively fixed (low impedance) voltage source. Therefore, if a filter capacitor is used, it is best for this capacitor to be a few orders of magnitude greater than the CINPUT. (A value of at least 100 pF works well.) This is not necessary, but it will work. If you do, be sure to use an RC filter on both pin 2 (VIN+) and pin 3 (VIN–) to limit the input voltage at both pads. Broadcom AV02-0410EN 18 HCPL-7800A/HCPL-7800 Data Sheet 4. How do I ensure that the HCPL-7800(A) is not destroyed as a result of short circuit conditions that cause voltage drops across the sense resistor that exceed the ratings of the HCPL-7800(A)’s inputs? Select the sense resistor so that it will have less than 5V drop when short circuits occur. The only other requirement is to shut down the drive before the sense resistor is damaged or its solder joints melt. This ensures that the input of the HCPL-7800(A) can not be damaged by sense resistors going open-circuit. Isolation and Insulation 1. How many volts can the HCPL-7800(A) withstand? The momentary (1 minute) withstand voltage is 3750V rms per UL 1577 and CSA Component Acceptance Notice #5. Isolation Amplifer 2. How long does the HCPL-7800(A) take to begin working properly after power-up? Within 1 ms after VDD1 and VDD2 powered the device starts to work. But it takes longer time for output to settle down completely. In case of the offset measurement while both inputs are tied to ground there is initially VOS adjustment (about 60 ms). The output completely settles down in 100 ms after device powering up. Miscellaneous 1. How does the HCPL-7800(A) measure negative signals with only a +5V supply? The inputs have a series resistor for protection against large negative inputs. Normal signals are no more than 200 mV in amplitude. Such signals do not forward bias any junctions sufficiently to interfere with accurate operation of the switched capacitor input circuit. Accuracy 1. Can the signal to noise ratio be improved? Yes. Some noise energy exists beyond the 100-kHz bandwidth of the HCPL-7800(A). Additional filtering using different filter R,C values in the post-amplifier application circuit can be used to improve the signal-to-noise ratio. For example, by using values of R3 = R4 = 10 kΩ, C5 = C6 = 470 pF in the application circuit, the rms output noise will be cut roughly by a factor of 2. In applications requiring only a few kHz bandwidth, even better noise performance can be obtained. The noise spectral density is roughly 500 nV/s Hz below 20 kHz (input referred). 2. Does the gain change if the internal LED light output degrades with time? No. The LED is used only to transmit a digital pattern. Broadcom has accounted for LED degradation in the design of the product to ensure long life. Power Supplies and Start-Up 1. What are the output voltages before the input side power supply is turned on? VO+ is close to 1.29 V and VO– is close to 3.80V. This is equivalent to the output response at the condition that LED is completely off. Broadcom AV02-0410EN 19 Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, and the A logo are among the trademarks of Broadcom and/or its affiliates in the United States, certain other countries, and/or the EU. Copyright © 2008–2020 Broadcom. All Rights Reserved. The term “Broadcom” refers to Broadcom Inc. and/or its subsidiaries. For more information, please visit www.broadcom.com. Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does not assume any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others.