HDSP-3903

HDSP-390x Series, HDSP-420x Series HDSP-860x Series, HDSP-N15x Series 20 mm (0.8 inch) Seven Segment Displays Data Sheet Description Features The 20 mm (0.8 inch) LED seven segment displays are designed for viewing distances up to 10 metres (33 feet). These devices use an industry standard size package and pinout. All devices are available as either common anode or common cathode. • Industry standard size • Industry standard pinout 15.24 mm (0.6 in.) DIP leads on 2.54 mm (0.1 in.) centers Applications • Choice of Colors AlGaAs Red, High Efficiency Red, Yellow, Green These displays are ideal for most applications. Pin for pin equivalent displays are also available in a low current design. The low current displays are ideal for portable applica­tions. For additional information see the Low Current Seven Segment Displays data sheet. • Excellent appearance Evenly lighted segments Mitered corners on segments Gray package gives optimum contrast ±50° viewing angle • Design flexibility Common anode or common cathode Left and right hand decimal points • Categorized for luminous intensity Yellow and green categorized for color Use of like categories yields a uniform display • High light output • High peak current • Excellent for long digit string multiplexing intensity and color selection option See Intensity and Color Selected Displays Data Sheet • Sunlight viewable AlGaAs Devices AlGaAs[1] HER HDSP-N150 HDSP-3900 HDSP-N151 HDSP-N153 Green Common Anode Left Hand Decimal A HDSP-3901 HDSP-4201 HDSP-8601 Common Anode Right Hand Decimal B HDSP-3903 HDSP-4203 HDSP-8603 Common Cathode Right Hand Decimal C Common Cathode Left Hand Decimal D HDSP-3905 Description Package Drawing Yellow Notes: 1. These displays are recommended for high ambient light operation. Please refer to the HDSP-N10x AlGaAs data sheet for low current operation. Part Numbering System 5082 - X X X X - X X X X X HDSP- X X X X - X X X X X Mechanical Options[1] 00: No Mechanical Option Color Bin Options[1,2] 0: No Color Bin Limitation Z: Color Bins 2- and 3+ Only (applicable for Yellow devices only) Maximum Intensity Bin[1,2] 0: No Maximum Intensity Bin Limitation Minimum Intensity Bin[1,2] 0: No Minimum Intensity Bin Limitation Device Configuration/Color[1] 0: Common Anode 1: Common Anode 3: Common Cathode Device Specific Configuration[1] Refer to Respective Datasheet Package[1] N: 20 mm (0.8 inch) Single Digit Seven Segment Display Notes: 1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Avago representative for details. 2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information. 2 Package Dimensions 11.07 (0.436) 11.07 (0.436) 8 20.32 (0.800) 1 2 3 4 5 6 7 8 9 18 17 16 15 14 13 12 11 10 8 10.16 (0.400) LHDP 1 2 3 4 5 6 7 8 9 13.08 (0.515) 27.69 0.25 (1.090 0.010) NOTE 4 NOTE 4 RHDP 8.25 (0.325) 8.25 (0.325) 1.27 (0.050) 18 17 16 15 14 13 12 11 10 1.27 (0.050) CL CHARACTER CL CL CHARACTER CL PACKAGE PACKAGE FRONT VIEW A, D FRONT VIEW B, C LUMINOUS INTENSITY CATEGORY 19.96 (0.786) 5.08 (0.200) COLOR BIN 6.1 MIN. (0.240) HDSP-39xx XYY Z * W 8.38 0.25 (0.330 0.010) 0.51 (0.020) 1.02 (0.040) PINS 2 & 17 0.38 (0.015) 2.54 0.25 (0.100 0.010) 15.24 0.25 (0.600 0.010) DATE CODE END VIEW SIDE VIEW THE SIDE VIEW OF PACKAGE *INDICATES COUNTRY OF ORIGIN. FUNCTION PIN 1 3 A NO PIN B NO PIN C NO PIN D NO PIN 2 CATHODE a CATHODE a ANODE a ANODE a 3 CATHODE f CATHODE f ANODE f ANODE f 4 ANODE [3] ANODE [3] CATHODE [6] CATHODE [6] 5 CATHODE e CATHODE e ANODE e ANODE e 6 ANODE [3] ANODE [3] CATHODE [6] CATHODE [6] 7 CATHODE dp NO CONNEC. NO CONNEC. ANODE dp 8 NO PIN NO PIN NO PIN NO PIN 9 NO PIN NO PIN NO PIN NO PIN 10 NO PIN CATHODE dp ANODE dp NO PIN 11 CATHODE d CATHODE d ANODE d ANODE d 12 ANODE [3] ANODE [3] CATHODE [6] CATHODE [6] 13 CATHODE c CATHODE c ANODE c ANODE c 14 CATHODE g CATHODE g ANODE g ANODE g 15 CATHODE b CATHODE b ANODE b ANODE b 16 NO PIN NO PIN NO PIN NO PIN 17 ANODE [3] ANODE [3] CATHODE [6] CATHODE [6] 18 NO PIN NO PIN NO PIN NO PIN NOTES: 1. DIMENSIONS IN MILLIMETERS AND (INCHES). 2. ALL UNTOLERANCED DIMENSIONS ARE FOR REFERENCE ONLY. 3. REDUNDANT ANODES. 4. UNUSED dp POSITION. 5. SEE INTERNAL CIRCUIT DIAGRAM. 6. REDUNDANT CATHODES. 7. FOR HDSP-420x/-860x SERIES PRODUCT ONLY. Internal Circuit Diagram 1 a 2 f 3 b 4 5 6 g e c 7 8 9 dp d 18 1 17 2 16 3 15 4 14 5 13 6 12 7 11 8 10 9 a f b g e c dp d A 18 1 17 2 16 3 15 4 14 5 13 6 12 7 11 8 10 9 a f b g c e dp d 18 1 17 2 16 3 15 4 14 5 13 6 12 7 11 8 10 9 18 a 16 b 15 g e 14 13 c 12 11 dp C B 17 f 10 d D Absolute Maximum Ratings AlGaAs Red HDSP-N150 Series HER HDSP-3900 Series Yellow HDSP-420x Series Green HDSP-860x Series Units 96 105 105 105 mW Peak Forward Current per Segment or DP 160[1] 135[3] 135[3] 90[5] mA DC Forward Current per Segment or DP 40[2] 40[4] 40[4] 30[6] mA –40 to +100 °C Description Average Power per Segment or DP Operating Temperature Range  –20 to +100 [7] –40 to +100 Storage Temperature Range –55 to +100 °C Reverse Voltage* per Segment or DP 3.0 V Wave Soldering Temperature for 3 Seconds (1.60 mm [0.063 in.] 250 °C * reverse voltage is for LED testing purposes and is not recommended to be used as an application condition. Notes: 1. See Figure 2 to establish pulsed conditions. 2. Derate above 55°C at 0.8 mA/°C. 3. See Figure 7 to establish pulsed conditions. 4. Derate above 50°C at 0.73 mA/°C. 5. See Figure 8 to establish pulsed conditions. 6. Derate above 50°C at 0.54 mA/°C. 7. For operation below –20°C, contact your local Avago components sales office or an authorized distributor. Electrical/Optical Characteristics at TA = 25°C AlGaAs Red Device Series - HDSP-N15x Parameter Symbol Min. Typ. Luminous Intensity/Segment[1,2,5] IV 6.0 Forward Voltage/Segment or DP VF (Digit Average) Units Test Conditions 14.0 mcd IF = 20 mA 1.8 V IF = 20 mA V IF = 100 mA 2.0 Max. 3.0 Peak Wavelength lPEAK 645 nm Dominant Wavelength[3] ld 637 nm Reverse Voltage/Segment or DP[4] VR 15 V Temperature Coefficient of VF /Segment or DP DVF/°C -2 mV/°C Thermal Resistance LED Junction-to-Pin RqJ-PIN 430 4 3.0 °C/W/Seg IR = 100 mA High Efficiency Red Device Series - HDSP-390x Parameter Symbol Min. Typ. Units Test Conditions Luminous Intensity/Segment [1,2] (Digit Average) IV 3350 7000 Max. mcd IF = 100 mA Peak: 1 of 5 df 4800 mcd IF = 20 mA V IF = 100 mA Forward Voltage/Segment or DP VF 2.6 Peak Wavelength lPEAK 635 nm Dominant Wavelength[3] ld 626 nm Reverse Voltage/Segment or DP[4] VR 25 V Temperature Coefficient of VF /Segment or DP DVF/°C -2 mV/°C Thermal Resistance LED Junction-to-Pin RqJ-PIN 375 3.0 3.5 IR = 100 mA °C/W/Seg Yellow Device Series - HDSP-420x Parameter Symbol Luminous Intensity/Segment [1,2] IV (Digit Average) Min. Typ. Max. Units Test Conditions 2200 7000 mcd IF = 100 mA Peak: 1 of 5 df mcd IF = 20 mA V IF = 100 mA 3400 Forward Voltage/Segment or DP VF Peak Wavelength lPEAK Dominant Wavelength[3,6] ld 581.5 586 Reverse Voltage/Segment or DP [4] VR 3.0 25.0 Temperature Coefficient ofVF /Segment or DP DVF/°C -2 RqJ-PIN 375 Thermal Resistance LED Junction-to-Pin 2.6 3.5 583 nm 592.5 nm V IR = 100 mA mV/°C °C/W/Seg Green Device Series - HDSP-860x Parameter Symbol Min. Typ. Luminous Intensity/Segment [1,2] (Digit Average)` IV 680 Forward Voltage/Segment or DP VF 2.1 Peak Wavelength lPEAK 566 Dominant Wavelength[3,6] ld 571 Reverse Voltage/Segment or DP [4] VR Temperature Coefficient of VF /Segment or DP DVF/°C -2 Thermal Resistance LED Junction-to-Pin RqJ-PIN 375 3.0 Units Test Conditions 1500 mcd IF = 10 mA 1960 mcd IF = 50 mA Peak: 1 of 5 df V IF = 10 mA 50.0 Max. 2.5 nm 577 nm V IR = 100 mA mV/°C °C/W/Seg Notes: 1. Case temperature of the device immediately prior to the intensity measurement is 25°C. 2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package. 3. The dominant wavelength, ld, is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device. 4. Typical specification for reference only. Do not exceed absolute maximum ratings. 5. For low current operation, the AlGaAs Red HDSP-N100 series displays are recommended. They are tested at 1 mA dc/segment and are pin for pin compatible with the HDSP-N150 series. 6. The Yellow (HDSP-420x) and Green (HDSP-860x) displays are categorized for dominant wavelength. The category is designated by a number adjacent to the luminous intensity category letter. 5 OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF I DC MAX. 10 IDC MAX 10 100 Z 0H 10 HZ 0 30 1 HZ 1k Z kH 1 0.1 HZ 3k IPEAK 100 10 RATIO OF MAXIMUM OPERATING PEAK CURRENT TO TEMPERATURE DERATED MAXIMUM DC CURRENT AlGaAs Red 1000 10,000 DC OPERATION t P Ð PULSE DURATION Ð µs IDC MAX – MAXIMUM DC CURRENT PER SEGMENT – mA 50 45 40 35 AlGaAs RED 30 25 20 RθJ-A = 525°C/W 15 10 5 0 10 20 30 40 50 60 70 80 90 100 110 IF – FORWARD CURRENT PER SEGMENT – mA Figure 1. Maximum allowed peak current vs. pulse duration – AlGaAs Red. 200 180 160 140 AlGaAs RED 120 100 80 60 40 20 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 TA – AMBIENT TEMPERATURE – °C VF – FORWARD CURRENT – V Figure 3. Figure 2. Maximum allowable DC current vs. ambient temperature. Figure 4. Figure 3. Forward current vs. forward voltage. 2.50 1.2 µPEAK – RELATIVE EFFICIENCY (NORMALIZED TO 1 AT 20 mA) RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 20 mA) 2.25 2.00 1.75 1.50 1.25 AlGaAs RED 1.00 0.75 0.50 0.25 0 0 5 10 15 20 25 30 35 40 45 50 IF – FORWARD CURRENT PER SEGMENT – mA Figure 5. Figure 4. Relative luminous intensity vs. DC forward current. 6 1.1 1.0 AlGaAs RED 0.9 0.8 0.7 0.6 2 3 4 5 10 20 30 40 50 100 200 IPEAK – PEAK FORWARD CURRENT PER SEGMENT Figure 5. Relative efficiency (luminous intensity per Figure 6. unit current) vs. peak current. RATIO OF MAXIMUM OPERATING PEAK CURRENT TO TEMPERATURE DERATED MAXIMUM DC CURRENT IPEAK IDC MAX 30 GREEN R θ J-A = 525¡ C/W 5 0 10 20 30 40 50 60 70 80 90 100 110 140 120 100 80 60 40 GREEN 20 0 0 1.0 1.5 2.0 2.5 3.0 3.5 Figure 9. Forward current vs. forward voltage. 1.5 4.0 µ˙ p eak Ð RELATIVE EFFICIENCY PEAK (NORMALIZED TO 1 AT 100 mA FOR HER AND YELLOW; AT 10 mA FOR GREEN) RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 20 mA FOR HER AND YELLOW; AT 10 mA FOR GREEN) 0.5 V F Ð FORWARD VOLTAGE Ð V Figure 8. Maximum allowable DC current vs. ambient temperature. 3.5 3.0 2.5 GREEN 2.0 1.5 HER AND YELLOW 1.0 0.5 0 5 10 15 20 25 30 35 40 I F Ð FORWARD CURRENT PER SEGMENT Ð mA Figure 10. Relative luminous intensity vs. DC forward current. 7 YELLOW HER TA Ð AMBIENT TEMPERATURE Ð ¡C 0 1000 10,000 Figure 7. Maximum allowed peak current vs. pulse duration – Green. I F Ð FORWARD CURRENT PER SEGMENT Ð mA I DC MAX Ð MAXIMUM DC CURRENT PER SEGMENT Ð mA HER / YELLOW 10 HZ 40 15 0 45 20 HZ 50 25 100 OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF I DC MAX. t P Ð PULSE DURATION Ð µS Figure 6. Maximum allowed peak current vs. pulse duration – HER, Yellow. 35 10 t P Ð PULSE DURATION Ð µS 10 0 30 1 Z kH 1 0.1 1 10,000 Z kH 1000 100 Z kH 10 10 3 DC OPERATION 1 100 10 HZ Z kH OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF I DC MAX. IDC MAX 1 1 0 10 10 Z kH IPEAK 100 10 RATIO OF MAXIMUM OPERATING PEAK CURRENT TO TEMPERATURE DERATED MAXIMUM DC CURRENT HER, Yellow, Green 1.4 1.3 1.2 1.1 1.0 0.9 GREEN HER 0.8 0.7 0.6 YELLOW 0.5 0.4 0.3 10 20 30 40 50 60 70 80 90 100 110 120 130 I PEAK Ð PEAK FORWARD CURRENT PER SEGMENT Ð mA Figure 11. Relative efficiency (luminous intensity per unit current) vs. peak current. DC OPERATION Intensity Bin Limits (mcd) Color Categories AlGaAs Red - HDSP-N15x Dominant Wavelength (nm) IV Bin Category Min. Max. J 6.14 11.20 K 9.20 16.90 L 13.80 25.30 M 20.70 38.00 N 31.10 56.90 O 46.60 85.40 Yellow - HDSP-420x IV Bin Category Min. Max. C 2.23 4.09 D 3.35 6.14 E 5.02 9.21 F 7.53 13.82 G 11.30 20.72 H 16.95 31.08 I 25.43 46.62 Color Bin Min. Max. Yellow 1 581.50 585.00 3 584.00 587.50 2 586.50 590.00 4 589.00 592.50 2 573.00 577.00 3 570.00 574.00 4 567.00 571.00 5 564.00 568.00 Green Note: All categories are established for classification of products. Products may not be available in all categories. Please contact your Avago representatives for further clarification/information. Contrast Enhancement For information on contrast enhancement, please see Application Note 1015. Soldering/Cleaning Green - HDSP-860x IV Bin Category Min. Max. D 1.03 1.88 E 1.54 2.82 F 2.31 4.25 G 3.47 6.37 H 5.21 9.55 IV Bin Category Min. Max. D 3.35 6.14 E 5.02 9.21 F 7.53 13.82 G 11.30 20.72 H 16.95 31.08 I 25.43 46.62 Cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloro- ethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. For information on soldering LEDs, please refer to Application Note 1027. HER - HDSP-390x For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2015 Avago Technologies. All rights reserved. Obsoletes 5988-1737EN AV02-2551EN - October 9, 2015