HDSP-815E

HDSP-815E/816E/815G/816G 20 mm (0.8 inch) General Purpose Seven Segment Displays Data Sheet Description Features These 20 mm (0.8 inch) displays use industry standard size and pin-out. The devices are available as either common anode or common cathode. Available in either red or green colors, these gray-faced displays are suitable for indoor use.  Industry standard size No color binning is offered for these parts.  Mitered font Mitered corners on segments These parts are subjected to Outgoing Quality Assurance (OQA) inspection with AQL of 0.065% for functional and visual/cosmetic rejects.  Industry standard pin-out 15.24 mm (0.6 in.) DIP leads on 2.54 mm (0.1 in.) centers  Choice of colors Red, Green  Gray face paint Gray package gives optimum contrast  ±50° Viewing angle  Design flexibility Common anode or common cathode Devices  Categorized for luminous intensity HER HDSP- Green HDSP- Description 815E 815G Common Anode Right Hand Decimal 816E 816G Common Cathode Right Hand Decimal Applications  Suitable for indoor use  Not recommended for industrial applications, i.e., operating temperature requirements exceeding 85° C or below -25° C [1]  Extreme temperature cycling not recommended [2] Notes: 1. For industrial applications, it is recommended to use HDSP-3901/ 3903/8601/8603. 2. For details, please contact your local Avago Technologies sales office or an authorized distributor. Part Numbering System 5082 – X XX X – X X X XX HDSP – X XX X – X X X XX Mechanical Options [1] 00 : No Mechanical Option Color Bin Options [1,2] 0 : No Color Bin Limitation Maximum Intensity Bins [1,2] 0 : No Maximum Intensity Bin Limitation Minimum Intensity Bins [1,2] 0 : No Minimum Intensity Bin Limitation Device Configuration/Color [1] E : High Efficiency Red G : Green Device Specific Configuration [1] Refer to Respective Datasheet Package [1] Refer to Respective Datasheet Notes: 1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Avago representative for details. 2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information. 2 Package Dimensions 11.07 (0.436) LUMINOUS INTENSITY CATEGORY 8° 4.60 (0.181) 16 1 13.08 (0.514) 20.32 (0.800) HDSP-XXXX XYY Z XXXX 1.70 (0.067) 27.69 ± 0.25 (1.090 ± 0.010) 6 DIA. 0.50 (0.020) 2.54 x 7 = 17.78 (0.100 x 7 = 0.700) 9 UNUSED DP 1.25 (0.049) RHDP SIDE VIEW C L CL COUNTRY OF ORIGIN DATE CODE 7.95 (0.313) CHARACTER PACKAGE FRONT VIEW NOTES: 1. DIMENSIONS IN MILLIMETERS AND (INCHES). 2. TOLERANCE IS 0.25 mm (0.010 INCH) UNLESS OTHERWISE STATED. 19.96 (0.786) 8.38 (0.330) 15.24 (0.600) 4.8 ± 0.50 (0.189 ± 0.020) END VIEW Internal Circuit Diagram COMMON ANODE PIN a 1 f 2 b 3 g 4 5 c e 6 DP 7 8 d COMMON ANODE 3 16 1 15 2 14 3 13 4 12 5 11 6 10 7 9 8 a 16 f 15 b 14 g 13 12 c e 11 DP d COMMON CATHODE 10 9 FUNCTION COMMON CATHODE PIN FUNCTION 1 CATHODE A 1 ANODE A 2 3 4 CATHODE F COMMON ANODE CATHODE E 2 3 4 ANODE F COMMON CATHODE ANODE E 5 COMMON ANODE 5 COMMON CATHODE 6 7 8 NO CONNECTION NO PIN NO PIN 6 7 8 NO CONNECTION NO PIN NO PIN 9 10 11 CATHODE RHDP CATHODE D COMMON ANODE 9 10 11 ANODE RHDP ANODE D COMMON CATHODE 12 CATHODE C 12 ANODE C 13 14 15 CATHODE G CATHODE B NO PIN 13 14 15 ANODE G ANODE B 16 COMMON ANODE 16 NO PIN COMMON CATHODE Absolute Maximum Ratings at TA = 25° C High Efficiency Red HDSP-815E HDSP-816E Parameter Green HDSP-815G HDSP-816G Units Average Power per Segment or DP 62.5 65 mW Peak Forward Current per Segment or DP (1/10 Duty Cycle, 0.1 ms Pulse Width) 100 90 mA DC Forward Current per Segment or DP [1] 25 25 mA Reverse Voltage per Segment or DP 3 3 V Operating Temperature -25 to +85 -25 to +85 °C Storage Temperature -25 to +85 -25 to +85 °C Wave Soldering Temperature for 3 Seconds [2] (1.6 mm [0.063 in.] below Body) 250 250 °C Notes: 1. Derate above 25° C at 0.33 mA/°C. 2. Not recommended to be soldered more than 2 times. Minimum interval between solderings is 15 minutes. Total soldering time not to exceed 5 seconds. Optical/Electrical Characteristics at TA = 25° C High Efficiency Red Devices HDSP- Parameter Symbol Min. Typ. 815E 816E Luminous Intensity/Segment (Segment Average)[1,2] Iv 2.3 4.8 Forward Voltage/Segment or DP VF 2.1 Peak Wavelength PEAK 635 nm Dominant Wavelength[3] d 626 nm Reverse Voltage/Segment or DP[4] VR 25 V Temperature Coefficient of VF/ Segment or DP VF/°C -2 mV/°C Devices HDSP- Parameter Symbol Min. Typ. 815G 816G Luminous Intensity/Segment (Segment Average)[1,2] Iv 1.5 3.3 3.0 Max. 3.0 Units Test Conditions mcd IF = 20 mA V IF = 20 mA IR = 100 A Green Max. Test Conditions mcd IF = 20 mA V IF = 20 mA Forward Voltage/Segment or DP VF 2.1 Peak Wavelength PEAK 566 nm Dominant Wavelength[3] d 571 nm Reverse Voltage/Segment or DP[4] VR Temperature Coefficient of VF/ Segment or DP VF/°C 3.0 2.6 Units 50 V -2 mV/°C IR = 100 A Notes: 1. Case temperature of the device immediately prior to the intensity measurement is 25° C. 2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package. 3. The dominant wavelength, d, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Typical specification for reference only. Do not exceed absolute maximum ratings. 4 RTJA = 525°C/W 35 30 25 20 GREEN, HER 15 10 5 0 10 20 30 40 50 60 70 80 TA – AMBIENT TEMPERATURE – °C 90 100 Figure 1. Maximum allowable DC current vs. ambient temperature. RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 20 mA) 1.75 1.50 1.25 1.00 0.75 HER GREEN 0.25 0 0 10 20 30 IF – FORWARD CURRENT PER SEGMENT – mA Figure 3. Relative luminous intensity vs. DC forward current. 5 100 80 60 40 GREEN 20 0 HER 0 1 2 3 VF – FORWARD VOLTAGE Figure 2. Forward current vs. forward voltage. 2.00 0.50 IF – FORWARD CURRENT PER SEGMENT – mA IDC MAX – MAXIMUM DC CURRENT PER SEGMENT – mA 40 40 4 5 Intensity Bin Limits (mcd at 20 mA) Contrast Enhancement HER/Green For information on contrast enhancement, please see Application Note 1015. Bin Name Green Min.[1] Max.[1] HER N NA NA P 7.57 10.78 Q 10.78 15.10 10.78 15.10 R 15.10 21.58 NA NA Max.[1] Soldering/Cleaning 5.31 7.57 7.57 10.78 Cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. Min.[1] Note: 1. All categories are established for classification of products. Products may not be available in all categories. Please contact your Avago representative for further clarification/information. For information on soldering LEDs please refer to Application Note 1027. Device Reliability Color Categories Dominant Wavelength (nm) Color Bin Min. Max. Green 1 569.00 572.00 2 572.00 575.00 For reliability information, please see the reliability data sheet 20 mm (0.8 inch) General Purpose Seven Segment Display. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes 5988-7999EN AV02-3639EN - June 20, 2012