HLMP-EJ37-R0PDD

HLMP-EJ37-R0PDD T-1 ¾ (5mm) Precision Optical Performance AlInGaP LED Lamp Data Sheet Description Features This Precision Optical Performance AlInGaP LED provide superior light output for excellent readability in sunlight and are extremely reliable. AlInGaP LED technology provides extremely stable light output over long periods of time. Precision Optical Performance lamps utilize the Aluminium Indium Gallium Phosphide (AlInGaP) technology. • Well defined Spatial radiation Patterns This LED lamp is orange tinted, nondiffused, T-1 ¾ package incorporating second generation optics producing well defined spatial radiation at specific viewing cone angle. This lamp is made with an advanced optical grade epoxy, offering superior high temperature and high moisture resistance performance in outdoor signal and sign applications. The high maximum LED junction temperature limit of +130°C enables high temperature operation in bright sunlight conditions. The package epoxy contains both uv-a and uv-b inhibitors to reduce the effects of long term exposure to direct sunlight. • High Luminous Output • AlInGaP Orange • High Operating Temperature: TJLED = +130°C • Superior Resistance to moisture Applications • Comercial Outdoor Advertising: - Signs - Marquees • Variable Message Sign Benefits • Superior Light Output performance In Outdoor Environments • Suitable for Auto-insertion into PC Boards Package Dimensions Device Selection Guide 5.00 ± 0.20 (0.197 ± 0.008) Part Number HLMP-EJ37-R0PDD 8.71 ± 0.20 (0.343 ±0.008) Luminous Intensity, Min (mcd at 20mA) 1500 Tolerance for luminous intensity is ±15%. Tolerance for color bin limit is ± 0.5 nm d 1.14 ± 0.20 (0.045 ± 0.008) 1.50 ± 0.15 (0.059 ± 0.006) 31.60 MIN. (1.244) Dominant Wavelength Range (nm) 605.5 -612.5 Notes: 1. The luminous intensity is measured on the mechanical axis of the lamp package. 3. The optical axis is closely aligned with the package mechanical axis. 4. The dominant wavelength, ld, is derived from the CIE Chromaticity Diagram and represents the color of the lamp. 5. θ1/2 is the off axis angle where the luminous intensity is one half the on-axis intensity. 0.70 (0.028) MAX. Absolute Maximum Rating (TA=25°C) CATHODE LEAD 1.00 MIN. (0.039) 0.50 ± 0.10 SQ. TYP. (0.020 ± 0.004) 5.80 ± 0.20 (0.228 ± 0.008) CATHODE FLAT 2.54 ± 0.38 (0.100 ± 0.015) Notes : 1. All dimensions are in milimetres (inches). 2. Leads are mild steel, solder dipped. 3. Tapers shown at top of leads (bottom of lamp package) indicate an epoxy meniscus that may extend about 1mm (0.040in.) down the leads. 4. Recommended PC board hole diameters = 0.965/0.889 (0.038/ 0.035) 5. For dome heights above lead standoff seating plane, d = 11.96 ± 0.25 (0.471 ± 0.010). 2 Parameters DC forward current[1] Peak pulsed forward current [2] Average forward current Reverse voltage (Ir = 100 mA) LED junction temperature Power Dissipation Operating temperature Storage temperature Through the wave soldering temperature Value 50 mA 100 mA 30 mA 5V 130oC 120mW -40oC to +100oC -40oC to +120oC 250oC for 3 seconds Note: 1. Derate linearly as shown in fugure 4. 2. For long terms performance with minimum light output degration, drive currents between 10mA and 30 mA are recommended. For more information on recommended drive condition, please refer to Application Brief I-024. 3. Operating at current below 1mA is not recommended. Please contact your local representative for further information. Electrical and Optical Characteristics (TA=25°C) Parameters Min Typ Max Unit Forward voltage 1.98 2.40 V Reverse voltage 5 20 V Peak Wavelength 609 nm Spectral Halfwidth 17 nm Speed of Response Capacitance Thermal Resistance 20 40 240 ns pF o C/W Test Condition IF= 20 mA IR= 100 µA Peak wavelength of spectrral distribution at I F= 20 mA Wavelength width at spectral distribution ½ power point at IF= 20 mA Exponential time constant VF=0, f=1 MHz LED Junction to cathode Notes: 1. The radiant intensity, Ie in watts per steradian, may be found from the equation Ie = Iv/hV where Iv is the luminous intensity in candelas and hV is the luminous efficacy in lumens/watt. 3.0 RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20 mA) 1.0 Relative Intensity 0.8 0.6 0.4 2.5 2.0 1.5 1.0 0.5 0 0.2 0 40 20 60 IF - DC FORWARD CURRENT - mA 0 550 600 650 700 Figure 3. Relative Luminous Intensity vs. Forward Current Wavelength (nm) Figure 1. Relative Intensity vs. Peak Wavelength 50 50 IF - FORWARD CURRENT - mA 45 Forward Current - If 40 35 30 25 20 15 10 RJA = 585 C/W 30 RJA = 780 C/W 20 10 0 5 0 20 40 60 80 100 TA - AMBIENT TEMPERATURE - C 0 0 0.5 1 1.5 Forward Voltage - Vf(V) Figure 2. Voltage 3 40 Forward Current vs. Forward 2 2.5 3 Figure 4. Maximum Forward Current vs. Ambient Temperature. Intensity Bin Limits (mcd at 20 mA) Relative Intensity 1 Bin Name R S T U V 0.5 Min. 1500 1900 2500 3200 4200 Max. 1900 2500 3200 4200 5500 Tolerance for each bin limits is ±15% 0 -50 - 40 -30 - 20 -10 0 10 20 30 40 50 Angle (deg) Figure 5. Spatial Radiation pattern Color Bin Limits (nm at 20 mA) Bin Name CA CB Min. 605.5 609 Max. 609 612.5 Tolerance for each bin limits is ±0.5nm Note: 1. Bin categories are established for classification of products. Product may not be available in all bin categories. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies Pte. All rights reserved. 5989-1391EN - May 29, 2006