HSMN-A430-U50M2

HSMx-A43x-xxxxx Surface Mount LED Indicator Data Sheet Description Features The Power PLCC-4 SMT LED with Lens are high-performance PLCC-4 package size SMT LEDs targeted mainly in Automotive & Electronics Signs and Signals (ESS) markets. These top-mount single-chip packages with focused radiation offer high brightness in beam direction and are excellent for interior automotive, indoor and outdoor sign and industrial applications. With additional lens in 30q variants, these products are especially fitting to applications for traffic lights, CHMSL and displays. x Industry Standard PLCC-4 x High reliability LED package x High brightness using AllnGaP and InGaN dice technologies x High optical efficiency x Narrow Viewing angle at 30° x Available in 8mm carrier tape on 7-inch reel x Compatible with both IR and TTW soldering process The PLCC-4 package family is able to dissipate heat better compared to the PLCC-2 packages. In proportion to this increase in driving current, this family of LEDs is able to produce higher light output compared to the conventional PLCC-2 SMT LEDs. Applications As an extension of the standard flat top PLCC-4 SMT LEDs, the Power PLCC-4 with Lens device is able to provide focused beams within narrow viewing angles (30q) meeting the market’s requirements for focused radiation and high brightness in beam directions. The Power PLCC-4 SMT LED with 30q is ideal for panel, push button, or general backlighting in automotive interior & exterior, sign, office equipment, industrial equipment and home appliances applications. This package design coupled with careful selection of component materials allow the Power PLCC-4 SMT LED with Lens to perform with higher reliability in a larger temperature range -40qC to 100qC. This high reliability feature is crucial to allow the Power PLCC-4 SMT LED with Lens to do well in harsh environments such as its target Automotive & ESS markets. The Power PLCC4 SMT LED with Lens package is also designed to be compatible with both IR-solder re-flow and throughthe-wave soldering. Interior automotive x x x x x x Instrument panel backlighting Central console backlighting Cabin backlighting Navigation and audio system Dome lighting Push button backlighting Exterior automotive x x x x Turn signals CHMSL Rear Combination Lamp Side repeaters Electronic signs and signals x Interior and exterior full color sign x Variable message sign x Garden lighting Office automation, home appliances, industrial equipment x Front panel backlighting x Push button backlighting x Display backlighting CAUTION: HSMN, HSMM-A43x-xxxxx LEDs are Class 2 ESD sensitive. Please observe appropriate precautions during handling and processing. Refer to Avago Application Note AN-1142 for additional details. The new Avago Technologies Power PLCC-4 SMT LED with 30° Lens will carry the part number HSMx- A43xxxxxx. The high brightness AlInGaP and InGaN dice technologies utilized will provide the product brightness that meets the Automotive and ESS markets requirements. The Lens package will complement and complete the existing AlInGap & InGaN color standard Power-PLCC-4 LED that Avago Technologies offers, providing customers an extra Lens option from one supplier. To facilitate easy pick and place assembly, the LEDs are packed in EIA-compliant tape and reel. Every reel will be shipped in single intensity and color bin (except for red color), to provide close uniformity Package Dimensions 2.8 ± 0.2 3.87 max. 2.2 ± 0.2 +ve 0.1 TYP. 0.80 ± 0.1 -ve 3.2 ± 0.2 3.5 ± 0.2 0.8 ± 0.3 -ve -ve 0.7 ± 0.1 Package marking Note: All dimensions in mm Electrical connection between all cathodes is recommended 2 0.5 ± 0.1 Device Selection Guide Color Part Number Min. IV (mcd) Typ. IV (mcd) Max. IV (mcd) Test Current (mA) Dice Technology Red HSMC-A430-W50M1 1125.00 2300.00 3550.00 50 AlInGaP HSMC-A431-X90M1 2240.00 4000.00 7150.00 50 AlInGaP HSMJ-A430-W50M1 1125.00 2300.00 3550.00 50 AlInGaP HSMJ-A431-X90M1 2240.00 4500.00 7150.00 50 AlInGaP HSMV-A430-Y90M1 3500.00 6000.00 11250.00 50 AlInGaP Orange HSML-A431-X90M1 2240.00 4500.00 7150.00 50 AlInGaP Amber HSMA-A430-W90M1 1400.00 3000.00 4500.00 50 AlInGaP HSMA-A431-Y00M1 2850.00 5000.00 - 50 AlInGaP HSMA-A431-X90M1 2240.00 4700.00 7150.00 50 AlInGaP Green HSMM-A430-W90M2 1400.00 2400.00 4500.00 30 InGaN Blue HSMN-A430-U50M2 450.00 950.00 1400.00 30 InGaN HSMN-A431-T50M2 285.00 360.00 900.00 30 InGaN Red Orange Notes: 1. The luminous intensity IV, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern may not be aligned with this axis. 2. Iv tolerance ±12% Part Numbering System HSM x1 - A X2 X3 X4 - X5 X6 X7 X8 X9 Packaging Option Color Bin Selection Intensity Bin Select Device Specific Configuration Package Type LED Chip Color 3 Absolute Maximum Ratings (TA=25°C) Parameters HSMC/A HSMV HSMK/M/N DC Forward Current [1] 70 mA 70 mA 30 mA Peak Forward Current [2] 200 mA 200 mA 90 mA Power Dissipation 180 mW 240 mW 114 mW Reverse Voltage 5V 5V 4V Junction Temperature 110 °C Operating Temperature - 40 °C to + 100 °C Storage Temperature - 40 °C to + 100 °C Notes: 1. Derate linearly as shown in Figure 4. 2. Duty factor = 10%, Frequency = 1kHz Optical Characteristics (TA = 25 °C) Peak Wavelength OPEAK (nm) Dominant Wavelength OD[1] (nm) Viewing Angle 2T½ [2] (Degrees) Luminous Efficacy KV [3] (lm/W) Color Part Number Dice Technology Typical Typical Typical Typical Red HSMC-A43x AlInGaP 635 626 30 150 Red Orange HSMJ-A43x AlInGaP 621 615 30 240 HSMV-A430 AlInGaP 623 617 30 263 Orange HSML-A431 AlInGaP 609 605 30 320 Amber HSMA-A43x AlInGaP 592 590 30 480 Green HSMM-A430 InGaN 518 525 30 500 Blue HSMN-A43X InGaN 468 470 30 75 Cyan HSMK-A43X InGaN 500 502 30 285 Notes: 1. The dominant wavelength, OD, is derived from the CIE Chromaticity Diagram and represents the color of the device. 2. T½ is the off-axis angle where the luminous intensity is ½ the peak intensity. 3. Radiant intensity, Ie in watts / steradian, may be calculated from the equation Ie = IV / KV, where IV is the luminous intensity in candelas and KV is the luminous efficacy in lumens / watt. Electrical Characteristics (TA = 25 °C) Forward Voltage VF (Volts)@IF=50 mA Reverse Voltage VR@100PA Reverse Voltage VR@10PA Part Number Minimum Typical Maximum Minimum Minimum HSMC/J/L/A 1.7 2.2 2.5 5 - HSMV 1.7 2.8 3.4 5 - Forward Voltage VF (Volts)@IF=30 mA Reverse Voltage VR@100PA Reverse Voltage VR@10PA Part Number Minimum Typical Maximum Minimum Minimum HSMK/M/N 2.7 3.9 4.6 - 5 4 1 InGaN Cyan RELATIVE INTENSITY 0.8 AlInGaP Amber InGaN Green 0.6 InGaN Blue AlInGaP Orange 0.4 AlInGaP Red Orange 0.2 AlInGaP Red 0 380 430 480 530 580 630 WAVELENGTH - nm 680 730 780 Figure 1. Relative Intensity Vs. Wavelength 80 FORWARD CURRENT - mA 70 HSMC/J/L/A 60 HSMV 50 40 30 20 HSMK/M/N 10 0 0 1 2 3 FORWARD VOLTAGE - V 4 5 Figure 2. Forward Current Vs. Forward Voltage 1.2 RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 30 mA) RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 50 mA) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 DC FORWARD CURRENT - mA Figure 3a. Relative Intensity Vs. Forward Current (AlInGaP). 5 1.0 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 DC FORWARD CURRENT - mA Figure 3b. Relative Intensity Vs. Forward Current (InGaN). 30 35 Figure 4a. Maximum Forward Current Vs. Ambient Temperature. Derated Based on TJmax= 110°C (AlInGaP) Figure 4b. Maximum Forward Current Vs. Ambient Temperature. Derated Based on TJmax= 110°C (InGaN) 1 0.9 NORMALIZED INTENSITY 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -90 -60 -30 0 30 ANGULAR DISPLACEMENT - DEGREES Figure 5. Radiation Pattern 6 60 90 X 2.60 (0.103) X 0.40 (0.016) 1.10 (0.043) 0.50 (0.020) Y 4.50 (0.178) 1.50 (0.059) Y DIMENSIONS IN mm (INCHES). SOLDER RESIST REPRESENTS ELECTRICAL CONNECTIVITY BETWEEN PADS Figure 6a. Recommended Soldering Pad Pattern (IR Reflow). X X 0.5 (0.020) 6.1 (0.240) 2.8 (0.110) Y 2.0 (0.079) 6.0 (0.236) 1.0 (0.039) 2.0 (0.079) 3.0 (0.118) Y DIMENSIONS IN mm (INCHES). SOLDER RESIST Figure 6b. Recommended Soldering Pad Pattern (TTW). 7 REPRESENTS ELECTRICAL CONNECTIVITY BETWEEN PADS Vacuum Pick-up Tool Nozzle Inner Diameter size: 1.0 to 1.5 mm Soft Tip 1.25mm Radius Contour Figure 7. Soft Tip Vacuum Pick-up Tool for Extracting SMT LED Components from Carrier Tape. 10 to 20 SEC. 20 SEC. MAX. 255 °C +5°C -0°C TEMPERATURE 183°C –6°C/SEC. MAX. 3°C/SEC. MAX. 120 SEC. MAX. TEMPERATURE 217°C 240°C MAX. 3°C/SEC. MAX. 100-150°C -6°C/SEC MAX. 3°C/SEC MAX. 125°C +/- 25°C 60-150 SEC. MAX. 120 SEC. 60-150 SEC. TIME TIME Figure 8a. Recommended SnPb Reflow Soldering Profile Figure 8b. Recommended Pb-free Reflow Soldering Profile. Note: For detail information on reflow soldering of Avago surface mount LEDs, do refer to Avago Application Note AN 1060 Surface Mounting SMT LED Indicator Components. TURBULENT WAVE 250 LAMINAR WAVE HOT AIR KNIFE BOTTOM SIDE OF PC BOARD TOP SIDE OF PC BOARD TEMPERATURE – C 200 CONVEYOR SPEED = 1.83 M/MIN (6 FT/MIN) PREHEAT SETTING = 150 C (100 C PCB) SOLDER WAVE TEMPERATURE = 245 C AIR KNIFE AIR TEMPERATURE = 390 C AIR KNIFE DISTANCE = 1.91 mm (0.25 IN.) AIR KNIFE ANGLE = 40 SOLDER: SN63; FLUX: RMA 150 FLUXING 100 NOTE: ALLOW FOR BOARDS TO BE SUFFICIENTLY COOLED BEFORE EXERTING MECHANICAL FORCE. 50 30 PREHEAT 0 10 20 30 40 50 60 TIME – SECONDS Figure 9. Recommended Wave Soldering Profile. 8 70 80 90 100 TRAILER COMPONENT LEADER 480 mm MIN. FOR ∅ 180 REEL. 960 mm MIN. FOR ∅ 330 REEL. 200 mm MIN. FOR ∅ 180 REEL. 200 mm MIN. FOR ∅ 330 REEL. C A USER FEED DIRECTION Figure 10. Tape Leader and Trailer Dimensions Figure 11. Tape Dimensions USER FEED DIRECTION CATHODE SIDE PRINTED LABEL Figure 12. Reeling Orientation. 9 Moisture Sensitivity Intensity Bin Select (X5X6) This product is qualified as Moisture Sensitive Level 2a per Jedec J-STD-020. Precautions when handling this moisture sensitive product is important to ensure the reliability of the product. Do refer to Avago Application Note AN5305 Handling of Moisture Sensitive Surface Mount Devices for details. Individual reel will contain parts from one half bin only X5 Min Iv Bin X6 0 Full Distribution A. Storage before use 2 2 half bins starting from X51 - Unopen moisture barrier bag (MBB) can be stored at