HSMQ-C280

HSMQ-C280 Miniature ChipLED Data Sheet Features  LED with InGaN die  Surface mount device with 0402 footprint  Compatible with reflow soldering  Tape in 8mm carrier tape on a 7 inch diameter reel Applications  Backlighting  Indicator Package Dimensions Note: 1. 2. All dimensions are in millimeters (inches). Tolerance ±0.1mm (±0.004in) unless otherwise specified. Caution: LEDs are class 1A ESD sensitive per ANSI/ESDA/JEDEC JS-001. Please observe appropriate precautions during handling and processing. Refer to Application Note AN-1142 for additional details. 1 Absolute Maximum Value at TJ = 25°C Parameter Green Unit Forward Current 20 mA Peak Pulsing Current2 100 mA Power Dissipation 78 mW LED Junction Temperature 95 °C Operating Temperature Range -30 to 85 °C Storage Temperature Range -40 to 85 °C 1 Note: 1. 2. Derate as shown in Figure 6. Pulse condition of 1/10 duty and 0.1ms width. Optical/Electrical Characteristics at TJ = 25°C, IF=20mA Parameter Min Typ Luminous Intensity Iv1 112.5 222.8 mcd 516 nm 522 nm 130 ° Peak Wavelength λp Dominant Wavelength λd 2 Viewing Angle 2θ1/23 Forward Voltage Vf 4 Reverse Voltage Vr at Ir=100μA 2.7 Max 3.9 5 Unit V V Thermal Resistance Rθj-p 300 °C/W Note: 1. 2. 3. 4. The luminous intensity is measured at the mechanical axis of the LED package. The actual peak of the spatial radiation pattern may not be aligned with the axis. The dominant wavelength is derived from the CIE Chromaticity Diagram and represents the perceived color of the device. Viewing angle is the off axis angle where the luminous intensity is ½ the peak intensity. Reverse voltage Indicates product final testing, long terms reverse bias is not recommended. 2 Luminous Intensity Bin Limits Bin ID N P Q R S T U Tolerance ±15% Green Color Bin Limits Bin ID A B C D Tolerance ±1nm Forward Voltage Bin Limits Bin ID Max 45.0 71.5 112.5 180.0 285.0 450.0 715.0 Dominant Wavelength (nm) Min 515 520 525 530 Max 520 525 530 535 Forward Voltage (V) Min 2.7 2.9 3.1 3.3 3.5 3.7 Max 2.9 3.1 3.3 3.5 3.7 3.9 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 FORWARD CURRENT - mA RELATIVE INTENSITY Z 1 2 3 4 5 Tolerance ±0.1V Luminous Intensity (mcd) Min 28.5 45.0 71.5 112.5 180.0 285.0 450.0 380 430 480 530 580 630 680 WAVELENGTH - nm 730 780 20 18 16 14 12 10 8 6 4 2 0 0 Figure 1. Spectrum 1 2 3 FORWARD VOLTAGE - V Figure 2. Forward current vs Forward voltage 3 4 6 DOMINANT WAVELENGTH SHIFT nm RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20 mA) 1 5 0.8 4 0.6 3 0.4 2 0.2 1 0 0 0 2 0 4 6 8 10 12 14 16 18 20 FORWARD CURRENT - mA 4 6 8 10 12 14 16 18 20 22 FORWARD CURRENT -mA Figure 4. Dominant wavelength shift vs Forward current Figure 3. Relative intensity vs Forward current 22 1.00 20 Rj-a=500°C/W Rj-a=600°C/W Rj-a=700°C/W Rj-a=850°C/W 18 FORWARD CURRENT - mA NORMALIZED INTENSITY 2 0.75 0.50 0.25 16 14 12 10 8 6 4 0.00 2 -90 -60 -30 0 30 60 ANGULAR DISPLACEMENT - DEGREES 90 0 0 Figure 5. Radiation pattern 10 20 30 40 50 60 70 80 AMBIENT TEMPERATURE - °C Figure 6. Derating curve Figure 7. Recommended solder pad 4 90 100 Figure 8. Reel orientation Figure 9. Reel dimensions 5 Figure 10. Carrier tape dimensions Soldering Recommended reflow soldering condition: (a) Reflow soldering must not be done more than 2 times. Do observe necessary precautions of handling moisture sensitive device as stated in below section. (b) Do not apply any pressure or force on the LED during reflow and after reflow when the LED is still hot. (c) It is preferred to use reflow soldering to solder the LED. But if unavoidable (such as rework), manual hand soldering can be used but must be strictly controlled to condition below: Soldering iron tip temperature = 310°C max Soldering duration = 2sec max Number of cycle = 1 only Power of soldering iron = 50W max (d) Do not touch the LED package body with the soldering iron except for the soldering terminals as it may cause damage to the LED. (e) User is advised to confirm beforehand whether the functionality and performance of the LED is affected by hand soldering. 6 PRECAUTIONARY NOTES 1. Handling of moisture sensitive device This product has a Moisture Sensitive Level 2a rating per JEDEC J-STD-020. Refer to Avago Application Note AN5305, Handling of Moisture Sensitive Surface Mount Devices, for additional details and a review of proper handling procedures. (a) Before use - An unopened moisture barrier bag (MBB) can be stored at