MSA-0486-TR2G

MSA-0486 Cascadable Silicon Bipolar MMIC Amplifier Data Sheet Description Features The MSA-0486 is a high performance silicon bipolar Monolithic Microwave Integrated Circuit (MMIC) housed in a low cost, surface mount plastic package. This MMIC is designed for use as a general purpose 50  gain block. Typical applications include narrow and broad band IF and RF amplifiers in commercial and industrial applications.  Lead-free Option Available The MSA-series is fabricated using Avago’s 10 GHz fT, 25 GHz fMAX, silicon bipolar MMIC process which uses nitride self-alignment, ion implantation, and gold metallization to achieve excellent performance, uniformity and reliability. The use of an external bias resistor for temperature and current stability also allows bias flexibility.  Unconditionally Stable (k>1) 86 Plastic Package Typical Biasing Configuration Rbias VCC t7 V RFC (Optional) 4 Cblock IN 1 MSA 2 Cblock 3 OUT Vd = 5.25 V  Cascadable 50  Gain Block  3 dB Bandwidth: DC to 3.2 GHz  8 dB Typical Gain at 1.0 GHz  12.5 dBm Typical P1 dB at 1.0 GHz  Surface Mount Plastic Package  Tape-and-Reel Packaging Option Available MSA-0486 Absolute Maximum Ratings Thermal Resistance [2, 4]: jc = 100°C/W Absolute Maximum [1] Parameter Device Current 85 mA Power Dissipation [2, 3] 500 mW RF Input Power +13 dBm Junction Temperature 150° C Storage Temperature -65 to 150° C Notes: 1. Permanent damage may occur if any of these limits are exceeded. 2. TCASE = 25° C. 3. Derate at 9.5 mW/°C for TC > 100° C. Electrical Specifications[1], TA = 25° C Symbol Parameters and Test Conditions: Id = 50 mA, ZO = 50  Units GP Power Gain (|S21|2) f = 0.1 GHz f = 1.0 GHz dB f = 0.1 to 2.0 GHz dB +0.6 GHz 3.2 Min. Typ. 7.0 8.3 8.0 GP Gain Flatness f3 dB 3 dB Bandwidth[2] VSWR Input VSWR f = 0.1 to 3.0 GHz 1.5:1 Output VSWR f = 0.1 to 3.0 GHz 1.9:1 NF 50  Noise Figure f = 1.0 GHz dB 7.0 P1dB Output Power at 1 dB Gain Compression f = 1.0 GHz dBm 12.5 IP3 Third Order Intercept Point f = 1.0 GHz dBm 25.5 tD Group Delay f = 1.0 GHz psec 140 Vd Device Voltage V dV/dT Device Voltage Temperature Coefficient mV/°C 4.2 5.25 Max. 6.3 -8.0 Notes: 1. The recommended operating current range for this device is 30 to 70 mA. Typical performance as a function of current is on the following page. Ordering Information Part Numbers No. of Devices Comments MSA-0486-BLK 100 Bulk MSA-0486-BLKG 100 Bulk MSA-0486-TR1 1000 7" Reel MSA-0486-TR1G 1000 7" Reel MSA-0486-TR2 4000 13" Reel MSA-0486-TR2G 4000 13" Reel Note: Order part number with a “G” suffix if lead-free option is desired. 2 MSA-0486 Typical Scattering Parameters (ZO = 50 , TA = 25° C, Id = 50 mA) Freq. GHz S11 Mag Ang dB Mag Ang dB Mag Ang Mag Ang 0.1 0.14 178 8.4 2.62 175 -16.2 0.154 1 0.16 -10 0.2 0.14 175 8.3 2.61 170 -16.3 0.153 2 0.16 -20 0.4 0.14 171 8.2 2.57 161 -16.2-3 0.154 3 0.16-7 -39 0.6 0.13 168 8.1 2.54 151 -16.0 0.158 4 0.18 -57 0.8 0.13 166 8.0 2.52 141 -5.9 0.161 5 0.20 -74 1.0 0.13 165 7.9 2.48 131 -15.7 0.165 6 0.18 -88 1.5 0.15 168 7.7 2.42 108 -14.8 0.182 8 0.27 -121 2.0 0.21 168 7.3 2.32 84 -14.0 0.199 7 0.32 -149 2.5 0.18 165 6.8 2.18 65 -13.1 0.222 4 0.38 -168 3.0 0.37 153 5.9 1.97 43 -12.7 0.231 -1 0.40 173 3.5 0.44 142 4.8 1.74 24 -12.5 0.238 -5 0.41 157 4.0 0.50 130 3.6 1.52 7 -12.5 0.238 -10 0.41 145 5.0 0.61 109 1.3 1.16 -21 -12.7 0.231 -17 0.43 132 3 S21 S12 S22 Typical Performance, TA = 25° C (unless otherwise noted) 10 80 60 6 Id (mA) Gp (dB) 8 Id = 30 mA Id = 50 mA Id = 70 mA 4 Gain Flat to DC 0.1 0.3 0.5 1.0 FREQUENCY (GHz) 3.0 0 6.0 Figure 1. Typical Power Gain vs Frequency, TA = 25° C. 1 2 3 4 Vd (V) 5 6 7 Figure 2. Device Current vs. Voltage. 21 13 12 18 P1 dB 11 8 GP Gp (dB) 9 7 P1 dB (dBm) P1 dB (dBm) 40 20 2 0 TC = +85° C TC = +25° C TC = –25° C 15 Id = 70 mA 12 Id = 50 mA 9 NF (dB) 8 NF 7 6 -25 0 +25 +55 TEMPERATURE (C) 6 3 0.1 +85 Figure 3. Output Power at 1 dB Gain Compression, NF and Power Gain vs. Case Temperature, f = 1.0 GHz, Id = 50 mA. 8.0 NF (dB) 7.5 Id = 30 mA Id = 50 mA Id = 70 mA 7.0 6.5 6.0 0.1 0.2 0.3 0.5 1.0 FREQUENCY (GHz) Figure 5. Noise Figure vs. Frequency. 4 2.0 Id = 30 mA 0.2 0.3 0.5 1.0 FREQUENCY (GHz) 2.0 Figure 4. Output Power at 1 dB Gain Compression vs. Frequency. 4.0 86 Plastic Package Dimensions 0.51 ±0.13 (0.020 ±0.005) GROUND RF OUTPUT AND DC BIAS 1 CL 3 2.34 ±0.38 (0.092 ±0.015) A04 45° RF INPUT GROUND 1.52 ±0.25 (0.060 ±0.010) 4 2 2.67 ±0.38 (0.105 ±0.15) 5° TYP. 0.66 ±0.13 (0.026 ±0.005) 2.16 ±0.13 (0.085 ±0.005) 0.203 ±0.051 (0.006 ±0.002) 8° MAX 0° MIN 0.30 MIN (0.012 MIN) Dimensions are in millimeters (inches) For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes 5989-2753EN AV02-3582EN - June 11, 2012