SFH551

SFH551/1-1 SFH551/1-1V Integrated Photo Detector Receiver for Plastic Fiber Plastic Connector Housing Data Sheet Description The SFH551/1V is a transimpedance amplifier with digital T TL open collector output stage and integrated photodiode. The active area of the detector in connection with the molded microlens gives an efficient coupling from the end of a plastic fiber. The receiver is fully DC coupled and therefore no line code is needed. The SFH551/1V includes a Schmitt trigger function to provide stable output states over the whole dynamic range. For optical input power levels above 6 μW typically the electrical output will be logical “low” and vice versa. With noise free Vcc and GND no undefined output signal is possible. SFH551/1 must not be used without shielding the ambient light, because ambient light causes malfunction when reaching the threshold level, noise or complete switching the output. Interference free transmission is possible by using the SFH551/1V with the black plastic connector housing. Features • Bipolar IC with open-collector output • Digital output, TTL compatible • Sensitive in visible and near IR range • Low switching threshold • Transfer rate ≤ 5 Mbit/s • 2.2 mm aperture holds standard 1000 micron plastic fiber • No fiber stripping required • Molded microlens for efficient coupling Plastic Connector Housing • Mounting screw attached to the connector • Interference-free housing • No cross talk • Auto insertable and wave solderable • Supplied in tubes transmission from light-tight • Transmitter and receiver can be flexibly positioned Ordering Information Type SFH551/1-1 SFH551/1-1V Ordering Code SP000063860 SP000063855 Applications • Household electronics • Power electronics • Optical networks V cc R pullup Data-out GND Figure 1. Block Diagram A bypass capacitor (100 nF) near the device (distance ≤ 3 cm) is necessary between ground and VCC. In critical applications the distance may be shorter. Technical Data Absolute Maximum Ratings Limit Values Parameter Operating Temperature Range Storage Temperature Range Soldering Temperature(mm from case bottom, t ≤ 5 s) Supply Voltage Range without Damage Recommended and Guaranteed Maximum Voltage Minimum Supply Voltage for Function Minimum Pull-up Resistance(VCC = 5 V) Output Voltage Output Current Power Dissipation (output) VCCmin Routmin V0 I0 P0 4 330 –0.5 15 50 100 Symbol TOP TSTG TS VCC –0.5 min. –40 –40 max. +85 +100 60 15 5.5 Unit °C °C °C V V V Ω V mA mW Characteristics (TA = 25°C, VCC = 4.75 to 5.25 V) Values Parameter Maximum Photosensitivity Wavelength Photosensitivity Spectral Range (S = 80% Smax) SFH551/1-1 OpticalThreshold Power (λ = 660nm) for Output Low Maximum Optical Power (λ = 660 nm) Maximum Value of tPLH at Maximum Power Optical Power for Output High without Errors (λ = 660nm) Propagation Delay (optical input to electrical output, with fast optical pulse) Current Consumption (without output current) Symbol λSmax λ ΦINth ΦINL ΦINH tPHL tPLH Icc 600 ≥6 ≥ – 1000 0 ≤ 0.1 ≤ –40 < 100 < 50 4 min. typ. 700 780 max. Unit nm nm μW dBm μW dBm μW dBm ns mA  Package Outlines Dimensions in mm Figure 2. SFH551/1-1 Dimensions in mm Figure. 3. SFH551/1-1V 3 Disclaimer The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved.We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Warnings Due to technical requirements components may contain dangerous substances. For information on the types inquestion please contact your nearest Avago Technologies Office. Avago Technologies Components may only be used in life-support devices or systems with the express written approval of Avago Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustainand/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons maybe endangered. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Avago Technologies Office (www.avagotech.com). For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright © 007 Avago Technologies Limited. All rights reserved. AV01-0713EN - July 0, 007