0402YD104KAT2A

X5R Dielectric General Specifications GENERAL DESCRIPTION • General Purpose Dielectric for Ceramic Capacitors • EIA Class II Dielectric • Temperature variation of capacitance is within ±15% from -55°C to +85°C • Well suited for decoupling and filtering applications • Available in High Capacitance values (up to 100µF) PART NUMBER (see page 2 for complete part number explanation) 1210 4 D Size Voltage (L” x W”) 4 = 4V 0101** 6 = 6.3V 0201 Z = 10V 0402 Y = 16V 0603 3 = 25V 0805 D = 35V 1206 5 = 50V 1210 1 = 100V 1812 **EIA 01005 107 Dielectric D = X5R Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros M A T Capacitance Tolerance K = ±10% M = ±20% Failure Rate A = N/A Terminations T = Plated Ni and Sn 2 A Packaging Special Code A = Std. 2 = 7” Reel 4 = 13” Reel U = 4mm TR (01005) NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. Temperature Coefficient 20 15 % Capacitance 10 0 -5 -10 -15 -20 -60 -40 -20 0 +20 +40 Temperature °C 26 +60 +80 Insulation Resistance (Ohm-Farads) TYPICAL ELECTRICAL CHARACTERISTICS 10,000 Insulation Resistance vs Temperature 1,000 100 0 20 40 60 80 100 120 Temperature °C 121818 X5R C0GDielectric (NP0) Dielectric Specifications Specificationsand andTest TestMethods Methods Parameter/Test Parameter/Test Operating Temperature Range Operating Temperature Range Capacitance Capacitance Q Factor Dissipation Insulation Resistance Insulation Resistance Dielectric Strength Dielectric Strength Capacitance Capacitance Variation Variation Dissipation Q Factor Insulation Insulation Resistance Resistance Solderability Solderability Appearance Appearance Capacitance Resistance to Resistance to Solder Heat Solder Heat Capacitance Variation Variation Q Dissipation Insulation Factor Resistance Insulation Dielectric Resistance Strength Dielectric Appearance Strength Capacitance Appearance Variation Thermal Shock Thermal Shock Capacitance Q Variation Dissipation Insulation Factor Resistance Insulation Dielectric Resistance Strength Appearance Dielectric Capacitance Strength Variation Appearance Load Life Load Life Capacitance Q Variation Cap) (C=Nominal Dissipation Insulation Factor Resistance Insulation Dielectric Resistance Strength Appearance Dielectric Capacitance Strength Variation Appearance Load Humidity Load Humidity Capacitance Q Variation Dissipation Insulation Factor Resistance Insulation Dielectric Resistance Strength Dielectric Strength 042418 100917 NP0 -55ºC Specification to +85ºC Limits -55ºC to +125ºC Within specified tolerance Within specified tolerance ≤ 2.5% for ≥ 50V DC rating 1000 pF Voltage: 1.0Vrms ± .2V .2V120Hz For Cap >Voltage: 10 µF, 1.0Vrms 0.5Vrms±@ Charge device with rated voltage for 60 ± 5 secs @ room temp/humidity Chargedevice devicewith with rated for for Charge 250% of voltage rated voltage 120 ± 5 secs @ room temp/humidity 1-5 seconds, w/charge and discharge current Charge devicelimited with 250% of rated to 50 mA (max)voltage for 1-5 seconds, w/charge and discharge current Note: Charge device with 150% of rated limited 50500V mA (max) voltagetofor devices. Deflection: 2mm Deflection: 2mm Test Time: 3030seconds Test Time: seconds Meets Initial Values(As (AsAbove) Above) Meets Initial Values ≥ Initial Valuex x0.3 0.3 ≥ Initial Value ≥ 95% of each terminal should be covered ≥ 95% of each terminal should be covered with fresh solder with fresh solder No defects,