06035C104KAZ2A

X7R Dielectric General Specifications X7R formulations are called “temperature stable” ceramics and fall into EIA Class II materials. X7R is the most popular of these intermediate dielectric constant materials. Its temperature variation of capacitance is within ±15% from -55°C to +125°C. This capacitance change is non-linear. Capacitance for X7R varies under the influence of electrical operating con-ditions such as voltage and frequency. X7R dielectric chip usage covers the broad spectrum of industrial applications where known changes in capacitance due to applied voltages are acceptable. PART NUMBER (see page 2 for complete part number explanation) 0805 5 C 103 M A T 2 A Size (L” x W”) Voltage 4V = 4 6.3V = 6 10V = Z 16V = Y 25V = 3 50V = 5 100V = 1 200V = 2 500V = 7 Dielectric X7R = C Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros Capacitance Tolerance J = ± 5%* K = ±10% M = ± 20% Failure Rate A = Not Applicable Terminations T = Plated Ni and Sn 7 = Gold Plated* Z= FLEXITERM®** Packaging 2 = 7” Reel 4 = 13” Reel Special Code A = Std. Product *≤1µF only, contact factory for additional values *Optional termination **See FLEXITERM® X7R section Contact Factory For Multiples NOTE: Contact factory for availability of Termination and Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. 042718 19 19 X7R Dielectric C0G (NP0)andDielectric Specifications Test Methods Specifications and Test Methods Parameter/Test X7R Specification Limits Operating Temperature Range Capacitance Parameter/Test Operating Temperature Range Capacitance Dissipation Factor Q Insulation Resistance Dielectric Strength Dielectric Strength Appearance Appearance Capacitance Capacitance Variation Variation Dissipation Q Factor Insulation Insulation Resistance Resistance Solderability Solderability Appearance Appearance Capacitance Capacitance Variation Variation Resistance Resistance to to Solder Heat Solder Heat Thermal Thermal Shock Shock Dissipation Q Factor Insulation Insulation Resistance Resistance Dielectric Dielectric Strength Strength Appearance Appearance Capacitance Capacitance Variation Variation Q Dissipation Factor Insulation Insulation Resistance Resistance Dielectric Dielectric Strength Strength Appearance Appearance Capacitance Variation Capacitance Load Life Load Life Variation Q Dissipation Cap) (C=Nominal Factor Insulation Insulation Resistance Resistance Dielectric Dielectric Strength Strength Appearance Appearance Capacitance Load Load Humidity Humidity Variation Capacitance Variation Q Dissipation Factor Insulation Insulation Resistance Resistance Dielectric Dielectric Strength Strength 20 100917 Within specified tolerance NP0 Specification Limits -55ºC to +125ºC ≤ 10% for ≥ 50V DC rating≤ 12.5% for 25V DC rating Within specified tolerance ≤ 12.5% for 25V and 16V DC rating 10µF, 05Vrm @ 120Hz 1.0 kHz ± 10% for cap > 1000 pF Voltage: 1.0Vrms ± .2V Charge voltage for for Chargedevice devicewith withrated rated voltage 120 60 ±± 55secs secs@@room roomtemp/humidity temp/humidity Charge of of rated voltage for for Chargedevice devicewith with250% 250% rated voltage 1-5 current 1-5seconds, seconds,w/charge w/chargeand anddischarge discharge current limited (max) limitedtoto5050mAmA (max) Note: 150% of rated Note:Charge Chargedevice devicewith with 150% of rated voltage devices. voltageforfor500V 500V devices. Deflection: 2mm Deflection: 2mm Test TestTime: Time:3030seconds seconds Meets MeetsInitial InitialValues Values(As (AsAbove) Above) ≥≥Initial InitialValue Valuex 0.3 x 0.3 95%ofofeach eachterminal terminalshould should covered ≥≥95% bebe covered withfresh freshsolder solder with defects,