X5R Dielectric
General Specifications
GENERAL DESCRIPTION
• General Purpose Dielectric for Ceramic Capacitors • EIA Class II Dielectric • Temperature variation of capacitance is within ±15% from -55°C to +85°C • Well suited for decoupling and filtering applications • Available in High Capacitance values (up to 100μF)
PART NUMBER (see page 2 for complete part number explanation)
1210
Size (L" x W")
4
Voltage 4 = 4V 6 = 6.3V Z = 10V Y = 16V 3 = 25V D = 35V 5 = 50V
D
Dielectric D = X5R
107
Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros
M
Capacitance Tolerance K = ±10% M = ±20%
A
Failure Rate A = N/A
T
Terminations T = Plated Ni and Sn
2
Packaging 2 = 7" Reel 4 = 13" Reel 7 = Bulk Cass. 9 = Bulk
A
Special Code A = Std.
NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values.
TYPICAL ELECTRICAL CHARACTERISTICS
Insulation Resistance (Ohm-Farads)
Temperature Coefficient
20 15
Insulation Resistance vs Temperature
10,000
Capacitance
10 5 0 -5 -10 -15 -20 -60 -40 -20 0 +20 +40 +60 +80
1,000
100
%
Temperature °C
0 0
20
40
60
80
100
120
Temperature °C
23
X5R Dielectric
Specifications and Test Methods
Parameter/Test Operating Temperature Range Capacitance Dissipation Factor X5R Specification Limits -55ºC to +85ºC Within specified tolerance ≤ 2.5% for ≥ 50V DC rating ≤ 3.0% for 25V DC rating ≤ 12.5% Max. for 16V DC rating and lower Contact Factory for DF by PN 100,000MΩ or 500MΩ - μF, whichever is less No breakdown or visual defects No defects ≤ ±12% Meets Initial Values (As Above) ≥ Initial Value x 0.3 ≥ 95% of each terminal should be covered with fresh solder No defects, 10 μF, 0.5Vrms @ 120Hz Charge device with rated voltage for 120 ± 5 secs @ room temp/humidity Charge device with 300% of rated voltage for 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Deflection: 2mm Test Time: 30 seconds
1mm/sec
Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance
Resistance to Flexure Stresses
Solderability Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength
Dip device in eutectic solder at 230 ± 5ºC for 5.0 ± 0.5 seconds
Resistance to Solder Heat
Thermal Shock
Load Life
Repeat for 5 cycles and measure after 24 ± 2 hours at room temperature Charge device with 1.5X rated voltage in test chamber set at 85ºC ± 2ºC for 1000 hours (+48, -0). Note: Contact factory for *optional specification part numbers that are tested at < 1.5X rated voltage. Remove from test chamber and stabilize at room temperature for 24 ± 2 hours before measuring. Store in a test chamber set at 85ºC ± 2ºC/ 85% ± 5% relative humidity for 1000 hours (+48, -0) with rated voltage applied. Remove from chamber and stabilize at room temperature and humidity for 24 ± 2 hours before measuring.
Load Humidity
24
X5R Dielectric
Capacitance Range
PREFERRED SIZES ARE SHADED
SIZE
Soldering Packaging
(L) Length (W) Width (t) Terminal MM (in.) MM (in.) MM (in.) WVDC 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 Cap (μF) 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 10 22 47 100 WVDC
0201
Reflow Only All Paper
0.60 ± 0.03 (0.024 ± 0.001) 0.30 ± 0.03 (0.011 ± 0.001) 0.15 ± 0.05 (0.006 ± 0.002) 4 6.3 10 16 25 A A A A A A A A A A
0402
Reflow Only All Paper
1.00 ± 0.10 (0.040 ± 0.004) 0.50 ± 0.10 (0.020 ± 0.004) 0.25 ± 0.15 (0.010 ± 0.006) 4 6.3 10 16 25 50
0603
Reflow Only All Paper
0805
Reflow/Wave Paper/Embossed
1206
Reflow/Wave Paper/Embossed
1210
Reflow/Wave Paper/Embossed
1812
Reflow Only All Embossed
1.60 ± 0.15 (0.063 ± 0.006) 0.81 ± 0.15 (0.032 ± 0.006) 0.35 ± 0.15 (0.014 ± 0.006) 4 6.3 10 16 25 35 50 6.3
2.01 ± 0.20 3.20 ± 0.20 (0.079 ± 0.008) (0.126 ± 0.008) 1.25 ± 0.20 1.60 ± 0.20 (0.049 ± 0.008) (0.063 ± 0.008) 0.50 ± 0.25 0.50 ± 0.25 (0.020 ± 0.010) (0.020 ± 0.010) 10 16 25 35 50 6.3 10 16 25 35 50
3.20 ± 0.20 4.50 ± 0.30 (0.126 ± 0.008) (0.177 ± 0.012) 2.50 ± 0.20 3.20 ± 0.20 (0.098 ± 0.008) (0.126 ± 0.008) 0.50 ± 0.25 0.61 ± 0.36 (0.020 ± 0.010) (0.024 ± 0.014) 4 6.3 10 16 25 35 50 6.3 10 25 50
Cap (pF)
C C C C C C C C C C C C C G G G G G G G G G G G G G G G G G G G G G G N N N N N N N N N N N N* * N N N N N N N N N* Q Q Q Q Q Q Q Q Q P* Q Q Q Q N N Q Q Q Q Q Q Z Q Q X Z Z Z X X
L
W T
A A A A A A A A
t
C C C C C C C C C C C C C
N N N N N Q X X
G G G G G G J K G J G J G J
J
X
Z
4 6.3 10 16 25
4 6.3 10 16 25 50
4 6.3 10 16 25 35 50 6.3 10 16 25 35 50 6.3 10 16 25 35 50
ZZZZ Z Z Z* 4 6.3 10 16 25 35 50 6.3 10 25 50
SIZE
Letter Max. Thickness A 0.33 (0.013)
0201
C 0.56 (0.022) E 0.71 (0.028) PAPER
0402
G 0.90 (0.035) J 0.94 (0.037)
0603
K 1.02 (0.040) M 1.27 (0.050) N 1.40 (0.055)
0805
P Q 1.52 1.78 (0.060) (0.070) EMBOSSED
1206
X 2.29 (0.090) Y 2.54 (0.100)
1210
Z 2.79 (0.110)
1812
= Under Development *Optional Specifications – Contact factory NOTE: Contact factory for non-specified capacitance values
25
很抱歉,暂时无法提供与“1210DD107MAT7A”相匹配的价格&库存,您可以联系我们找货
免费人工找货