609176001521000

SINGLE IDC CONTACT 18-24 AWG: 9176-500 General Information The 917X series of surface mount Insulation Displacement Connectors (IDC) were developed to meet the harsh automotive and industrial market applications for connecting individual wires directly to a PCB ranging from 14 AWG to 28 AWG. This industry proven contact system has been tested to automotive levels of shock, vibration, and temperature cycling to prove their reliability and robustness. This new single contact was developed as a standalone component to enhance the application uses with the IDC technology. The simplicity of inserting a wire into an SMT contact with a small tool or optional retention / termination cap allows a wide range of devices to be connected to the PCB without soldering. In SSL applications specifically, these contacts are used to bring power and signal onto the PCB or are used to daisy chain multiple boards together in a long string. While the IDC contact provides a gas-tight connection to conductor of the wire, the optional cap provides a positive strain relief even in the harshest conditions. In case of repair, the wires can be removed and replace up to three times. The single 9176 series contact and cap accepts 18 AWG to 24 AWG wires with an insulation diameter ranging from 1.1mm to 2.1mm. These dual beam contacts support a 10 amp current rating with a large SMT solder base to provide maximum stability on the PCB. The optional locking strain relief cap acts as the termination tool for severe vibration applications. FEATURES AND BENEFITS APPLICATIONS • Connecting discrete wire components directly to the PCB • Bringing power and signals onto a PCB • Daisy chaining PCB’s together to create a continuous string of boards • Application notes: refer to 201-01-124 • • • • • • IDC contact is supplied in T&R pockets for standard SMT placement IDC contact provides a gas-tight connection to the PCB for long term reliability Optional termination cap provides additional strain relief for severe environments Tested to automotive levels on shock, vibration and temperature cycling for reliability Reduced total applied cost versus solder or crimp processes Individual contacts can be located anywhere on the PCB based on specific application ELECTRICAL ENVIRONMENTAL MECHANICAL • Current Rating: 10 Amps/Contact • Voltage Rating: Dependant on component proximity • Operating Temperature: -40ºC to +125ºC • • • • Insulator Material: Nylon 46: UL94V0 Contact Material: Phosphor Bronze Plating: Tin over Nickel Durability: 3 Cycles HOW TO ORDER – CONTACT OPTIONS 70 9176 001 4XX Prefix 70 = Contact Series Number of Ways Wire Gauge Size No of Code Details Ways 001 1 Page 39 006 Code Accepted Wire Gauge 501 511 522 532 18 Gauge Stranded 20 Gauge Solid or Stranded 22 Gauge Solid or Stranded 24 Gauge Solid or Stranded Plating Option 006 = Pure Tin all over HOW TO ORDER – CAP OPTIONS 60 9176 001 5XX Prefix 60 = Cap Series Number of Ways Wire Gauge Size No of Code Details Ways Wire Insulation Code (AWG) 001 1 Page 43 516 521 X00 Insulator Color 1.1-1.6 (22-24) 1.6-2.1 (18-20) Code 000 Color Black Application Industrial 100 White Lighting CONNECTOR/TOOLING PART NUMBER MATRIX SERIES 9176-500 IDC HAND INSERTION TOOLING* ACCESSORY CAPS Wire Plastic Metal Cap Application AWG Positions Part Number White Black Insulation (medium volume) (high volume) Tool 18 Ø 1.6 - 2.1 1p 709176001501006 069176702001000 069176701901000 069176701801000 609176001521100 609176001521000 20 Ø 1.6 - 2.1 1p 709176001511006 069176702001000 069176701901000 069176701801000 609176001521100 609176001521000 22 Ø 1.1 - 1.6 1p 709176001522006 069176702002000 069176701902000 069176701801000 609176001516100 609176001516000 24 Ø 1.1 - 1.6 1p 709176001532006 069176702002000 069176701902000 069176701801000 609176001516100 609176001516000 * Hand Insertion Tooling and Cap Application - Universal Hand Tool 067000773001000; Consult Application Notes 201-01-124 Certification: UL File #E90723 The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 090721 – wire-to-board connectors – 39 SINGLE IDC CONTACT 18-24 AWG: 9176-500 Contact Details CONTACT DETAILS Code Accepted Wire Gauge 501 18 AWG Stranded 511 20 AWG Solid and Stranded 522 22 AWG Solid and Stranded 532 24 AWG Solid and Stranded AREA AVAILABLE FOR PICK & PLACE 2.00mm SQUARE NOTES: 1. CONNECTOR FOR IDC WIRE TO BOARD CONNECTION. 2. CONTACT MATERIAL: PHOSPHOR BRONZE. 3. CONTACT PLATING: PURE TIN. 4. CONNECTOR DESIGNED TO ACCEPT BETWEEN 20AWG AND 24AWG SOLID AND STRANDED WIRES, 18AWG WILL ONLY ACCEPT STRANDED WIRES, SEE TABLE. 5. ALL DIMENSIONS ±0.20 UNLESS TOLERANCED 6. FOR FULL PRODUCT SPECIFICATION REFER TO ELCO SPEC 201-01-126 AND APPLICATION NOTES 201-01-124. 7. SMT PCB LAYOUT, REFER TO SHEET 3. 8. PACKING IN TAPE AND REEL, QUANTITY 1000 PER REEL. 9. WHEN REQUIRED, MATCHING CAP DETAILS ON DRAWING 60-9176-001-5XX-X00S 10. ASSEMBLY TOOLING ON SHEETS 4 (WITH CAP) AND 5 (WITHOUT CAP). PACKING DETAILS REEL QTY LEADER TRAILER 1000 480mm 120mm 16 UNREELED DIRECTION 40 The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 090721 – wire-to-board connectors – 8 A 0.74 0.60 0.47 0.37 SINGLE IDC CONTACT 18-24 AWG: 9176-500 PBC Layout 18-24 AWG IDC WIRE TO BOARD CONNECTOR SINGLE CONTACT SMT PCB LAYOUT PURE TIN PADS ORIENTATION OF CONTACT ON PAD ASSEMBLED/INSTALLED PRODUCTS NOTES: 1. CONNECTOR CAN BE USED WITH CONTACT ONLY OR WITH OPTIONAL CAP. 2. OUTLINE OF CAP WHEN USED. 3. FOR FULL PRODUCT SPECIFICATION REFER TO ELCO SPEC 201-01-126 AND 201-01-124. 4. ALL DIMENSIONS ±0.20 UNLESS TOLERANCED. 5. ASSEMBLY TOOLING ON SHEETS 4 (WITH CAP) AND 5 (WITHOUT CAP). 6. WIRE CENTRE LINE HEIGHT ABOVE THE PCB, THIS INCLUDES AN ALLOWANCE OF 0.10MM FOR SOLDER AND The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 090721 – wire-to-board connectors – 41 SINGLE IDC CONTACT 18-24 AWG: 9176-500 Assembly Tooling ASSEMBLY TOOLING – CAP USED NOTES: 1. ASSEMBLY TOOLING FOR CAP. 2. AREA OF PCB TO BE KEPT CLEAR OF COMPONENTS, TACKS PERMISSIBLE. 3. WIRE AND CAP INSERTED IN ONE OPERATION. 4. REFER TO APPLICATION NOTE 201-01-124 FOR FURTHER INFORMATION. 5. REFER BELOW WHEN CONTACT USED WITHOUT CAP. 42 The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 090721 – wire-to-board connectors – SINGLE IDC CONTACT 18-24 AWG: 9176-500 Assembly Tooling ASSEMBLY TOOLING – CAP NOT USED WIRE ONTO CONTACT NOTES: 1. ASSEMBLY TOOLING FOR CONTACT ONLY, NO CAP USED. 2. MINIMUM AREA OF PCB TO BE KEPT CLEAR OF COMPONENTS, TRACKS PERMISSIBLE. 3. REFER TO TABLE FOR CORRECT TOOL/WIRE COMBINATION. 4. REFER TO APPLICATION NOTE 201-01-124 FOR FURTHER INFORMATION WIRE INSULATION Ø 1.10 to 1.60 1.60 to 2.10 METAL TOOL HIGH VOLUME 06-9176-7019-02-000 06-9176-7019-01-000 PLASTIC TOOL SMALL TO MEDIUM VOLUME 06-9176-7020-02-000 06-9176-7020-01-000 HANDLE 06-7000-7730-01-000 06-7000-7730-01-000 The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 090721 – wire-to-board connectors – 43 SINGLE IDC CONTACT 18-24 AWG: 9176-500 Cap Details CAP DETAILS Code Insulator Diameter (AWG) B Text C 516 1.1 to 1.6 (22-24) 1.00 Ø 1.6 521 1.6 to 2.1 (18-20) 1.50 Ø 2.1 NOTES: 1. CAP FOR IDC WIRE TO BOARD CONNECTION. 2. CAP MATERIAL: GLASS FILLED NYLON 46, COLOR SEE PAGE 41. 3. CAPS DESIGNED TO ACCOMMODATE WIRE INSULATION DIAMETERS 1.1MM TO 2.1MM. 4. ALL DIMENSIONS FOR REFERENCE UNLESS OTHERWISE STATED. 5. FOR FULL PRODUCT SPECIFICATION REFER TO ELCO SPEC 201-01-106, APPLICATION NOTES 201-01-124. 6. PACKING IN BAGS, QUANTITY 1000 PER BAG. 7. FOR INSTALATION DETAILS REFER TO DRAWING 70-9176-001-XX-006S. 44 The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 090721 – wire-to-board connectors –