CX3225GB16384P0HPQCC

Specification Drawing No. K1101-13754-432 1/11 Issued Date. Jan.24,2014 TO: Digi-Key Note：In case of specification change, KYOCERA Part Number also will be changed. Product Name Quartz Crystal Product Model CX3225GB Frequency Refer to K1101-13754-432 3/11 Nominal Frequency Customer Part Number - Customer Specification Number - KYOCERA Part Number Refer to K1101-13754-432 3/11 KYOCERA Part Number Remarks RoHS Compliant、MSL 1 Customer Acceptance Accept Signature Approved Date Department Person in charge Seller KYOCERA Corporation Manufacturer KYOCERA Crystal Device Corporation 6 Takeda Tobadono-cho, Fushimi-ku, Kyoto 612-8501 Japan TEL. No. 075-604-3500 FAX. No. 075-604-3501 5850, Higashine-Koh, Higashine-Shi, Yamagata 999-3701 Japan TEL. No. 0237-43-5611 FAX. No. 0237-43-5615 Design Department Quality Assurance Approved by Checked by Issued by KYOCERA Crystal Device Corporation Crystal Design Section A.Kikuchi Y.Takahashi Crystal Units Division T.Nitoube M.Hashimoto KYOCERA Crystal Device Corporation KBS-5079E Drawing No. K1101-13754-432 2/11 Revision History Rev.No. 1 2 Description of revise First Edition ･Frequency Addition. 49152kHz Date Approved by Checked by Issued by Jul.29,2013 Y.Takahashi T.Nitoube M.Konno Jan,24,2014 Y.Takahashi T. Nitoube M.Hashimoto KYOCERA Crystal Device Corporation KBS-5079E Drawing No. K1101-13754-432 3/11 [PART NUMBER LIST] Nominal Frequency (MHz) KYOCERA Part Number ESR (Ω) Nominal Frequency Code 10 CX3225GB10000P0HPQCC 300 10000 12 CX3225GB12000P0HPQCC 250 12000 12.288 CX3225GB12288P0HPQCC 250 12288 13 CX3225GB13000P0HPQCC 250 13000 13.56 CX3225GB13560P0HPQCC 250 13560 14.31818 CX3225GB14318P0HPQCC 100 14318 14.7456 CX3225GB14745P0HPQCC 100 14745 16 CX3225GB16000P0HPQCC 80 16000 16.384 CX3225GB16384P0HPQCC 80 16384 18.432 CX3225GB18432P0HPQCC 80 18432 19.2 CX3225GB19200P0HPQCC 80 19200 20 CX3225GB20000P0HPQCC 60 20000 22.5792 CX3225GB22579P0HPQCC 60 22579 24 CX3225GB24000P0HPQCC 60 24000 24.576 CX3225GB24576P0HPQCC 60 24576 25 CX3225GB25000P0HPQCC 60 25000 27 CX3225GB27000P0HPQCC 50 27000 27.12 CX3225GB27120P0HPQCC 50 27120 30 CX3225GB30000P0HPQCC 50 30000 32 CX3225GB32000P0HPQCC 50 32000 33.333 CX3225GB33333P0HPQCC 50 33333 36 CX3225GB36000P0HPQCC 50 36000 38.4 CX3225GB38400P0HPQCC 50 38400 40 CX3225GB40000P0HPQCC 50 40000 48 CX3225GB48000P0HPQCC 50 48000 49.152 CX3225GB49152P0HPQCC 50 49152 50 CX3225GB50000P0HPQCC 50 50000 54 CX3225GB54000P0HPQCC 50 54000 KYOCERA Crystal Device Corporation KBS-5079E Drawing No. K1101-13754-432 4/11 1. APPLICATION This specification sheet is applied to quartz crystal “CX3225GB” 2. KYOCERA PART NUMBER Refer to K1101-13754-432 3/11 KYOCERA Part Number 3. RATINGS Items SYMB. Rating Unit Operating Temperature Topr -40~+85 °C Storage Temperature Range Tstg -40~+85 °C Remarks 4. CHARACTERISTICS 4-1 ELECTRICAL CHARACTERISTICS Items SYMB. Electrical Specification Min. Typ. Max. Fundamental Unit F0 ※1 MHz TNOM +25 °C CL 18.0 pF Mode of Vibration Nominal Frequency Nominal Temperature Load Capacitance Frequency Tolerance Frequency Temperature Characteristics Frequency Aging Rate Equivalent Series Resistance Drive Level Insulation Resistance df/F -20.0 +20.0 df/F -30.0 +30.0 Test Condition Remarks +253°C -40~+85°C PPM -5.0 ESR Pd 0.01 IR 500 +5.0 1 year ※2 Ω 100 μW MΩ +253°C 100V(DC) ※1 Refer to K1101-13754-432 3/11 Nominal Frequency ※2 Refer to K1101-13754-432 3/11 ESR KYOCERA Crystal Device Corporation KBS-5079E Drawing No. K1101-13754-432 5/11 5. APPEARANCES, PHYSICAL DIMENSION OUTLINE DIMENSION (not to scale) CONNECTION （TOP VIEW） 1 3.20±0.1 NC 4－R0.20 Pin4 Pin4 HOT Pin3 Pin1 HOT Pin2 NC Pin3 2.50±0.1 ※ 3 K401F 0.2±0.05 2 3 4 0.8±0.1 Pin2 Pin1 PIN No. Pin1 Pin2 Pin3 Pin4 4－0.2±0.1 8－0.10±0.1 PIN Layout HOT NC HOT NC Pin2 Pin1 C 0.30 Pin4 Pin3 4－0.75±0.1 4－1.00±0.1 ※There is not consistency of a direction of indication for NC. UNIT： mm MARKING 1 Nominal Frequency 2 Identification 3 Date Code 4 Manufacturing Location Move the number of maximum indication beams of the frequency to five digits，and omit less than kHz． Year…LAST 1 DIGIT of YEAR AND WEEK (Ex) Jan. 1, 2014 → 401 F…KYOCERA Crystal Device Philippines, Inc ※3 Refer to K1101-13754-432 3/11 Nominal Frequency Code. The font of marking is reference. KYOCERA Crystal Device Corporation KBS-5079E Drawing No. K1101-13754-432 6/11 6. RECOMMENDED LAND PATTERN (not to scale) 1.0 1.3 1.05 0.8 1.05 1.3 UNIT： mm KYOCERA Crystal Device Corporation KBS-5079E Drawing No. K1101-13754-432 7/11 7.TAPING & REEL 梱包補助材 7-1.Dimensions 4.0±0.1 φ1.55±0.05 Unreeling direction 1.75±0.1 2.0±0.05 (3.7) 3.5±0.1 3.5±0.05 (3.0) 2.8±0.1 4.0±0.1 1.0±0.1 0.25±0.05 8.0±0.2 φ1.05±0.15 7-2.Leader and trailer tape Components Empty compartment Empty compartment Leader END START 160mm or more 100mm or more 400～560mm 7-3.Direction（The direction shall be seen from the top cover tape side） Unreeling direction 7-4.Specification 1. Material of the carrier tape shall be PS (ESD). 2. Material of the seal tape shall be polyester(ESD). 3. The seal tape shall not cover the sprocket holes. And not protrude from the carrier tape. 4. Tensile strength of the tape : 10N or more. 5. The R of the corner without designation is 0.2RMAX. 6. Disalignment between centers of the cavity and sprocket hole shall be 0.05mm or less. 7. Cumulative pitch tolerance of “P0” shall be ±0.2mm at 10 pitches. 8. The number of lack is 0.1% of 1 reel total part number (the number of the table letters) or the part following whose 1 either is big. (But, the thing which lack of the continuance is not in.) 9. The marking on parts is not fixed its direction, its electrical characteristic is equal. 10. Peeling force of the seal tape: 0.1 to 1.0N. Cover tape 165°～180° Career tape KYOCERA Crystal Device Corporation KBS-5079E Drawing No. K1101-13754-432 8/11 7-5.Reel specifications W C t D E B A (Nonconductor type Reel) In the case of Φ180 Reel (3000 pcs max, every 1000 pcs) Dimension Symbol Dimension A B C D φ180 +0/-1.5 φ60 +1/-0 φ13±0.2 φ21±0.8 E W t 2.0±0.5 9±1 2.0±0.5 (Unit : mm) KYOCERA Crystal Device Corporation KBS-5079E Drawing No. K1101-13754-432 9/11 8.Enviromental requirements After following test, frequency shall not change more than ±20×10－６ And CI，±20% or 5Ωof large value. 8.1 Resistance to Shock Test condition Natural dropped from height 100cm onto hard wood board in 3 times 8.2 Resistance to Vibration 8.3 Resistance to Heat Test condition frequency ： 10－55 －10 Hz Amplitude ： 1.5mm Cycle time ： 15 minutes Direction ： X,Y,Z (3direction),2 h each. Test condition The quartz crystal unit shall be stored at a temperature of +85±2°C for 500 h. Then it shal be subjected to standard atmospheric conditions for 1 h ,after whichi measurement shall be made. 8.4 Resistance to Cold Test condition The quartz crystal unit shall be stored at a temperature of -40±2°C for 500 h. Then it shal be subjected to standard atmospheric conditions for 1 h ,after whichi measurement shall be made. 8.5 Thermal Shock Test condition The quartz crystal unit shall be subjected to 500 succesive change of temperature cycles ，each as shown in table below，Then it shall be subjected to standard atmospheric conditions for 1h，after which measurements shall be made. Cycle ：-40±2°C（30min.）to 25±2°C（5min.） to +85±2°C（30min.）to 25±2°C（5min.） KYOCERA Crystal Device Corporation KBS-5079E Drawing No. 8.6 Resistance to Moisture K1101-13754-432 10/11 Test condition The quartz crystal unit shall be stored at a temperature of 60±2°C wich relative humidity of 90% to 95% for 240 h. Then it shall be subjected to standard atmospheric conditions for 1h，after which measurements shall be made 8.7 Soldering condition 1.） Material of solder Kind … lead free solder paste Melting point … +220±5°C 2.） Reflow temp.profile Temp [°C] Preheating +150 to +180 Peak +260±5 Total ― Frequency shift : ±2ppm 3.） Hand Soldering +350°C 3 sec MAX 4.） Reflow Times 2 times Time[sec] 150 (typ.) 10 (max.) 300 (max.) Reflow temp.profile 8.8 Intensity for bending in circuit board Solder this product in center of the circuit board of 40mm×100mm， and add the deflection of 3mm as the bottom figure. Test board : t＝1.6mm 20 PUSH 1.6 board 10 R5 Product 45 45 R340 press jig UNIT : mm KYOCERA Crystal Device Corporation KBS-5079E Drawing No. K1101-13754-432 11/11 9.Cautions for use （1）Automatic mounting machine use Please use after affirmation that select the mounting machine model with a shock small if possible in the case of use of an automatic mounting machine, and it does not have breakage. There is a risk of a quartz crystal unit breakage occurring and not functioning normally by too much shock etc.. （2）Conformity of a circuit In case of use of an oscillation circuit, please insert in a quartz crystal unit in series resistance 5 time as many as the standard value of equivalent in-series resistance, and confirm oscillating. Please remove resistance which inserted after the notes above-mentioned examination in the quartz crystal unit in series, and use it. （3）After making the Quartz Crystal mount on a printed circuit board ,if it is required to devide the printed circuit board into another one, use it with attentive confirmation so that a warp cased by this dividing might not affect any damage. When designing a printed circuit board as well as handling the mounting As much as possible. The quartz crystal shall be passed through the reflow furnace. Then it shall be subjected to standard atmospheric conditions, after which cleaning shall be made. 10.Storage conditions Storage at prolonged high temperature or low temperature and the storage by high humidity cause degradation of frequency accuracy, and degradation of soldering nature. Storage is performed at the temperature of 18-30 degrees C, and the humidity of 20-70 Percent in the state of packing, and a term is 6 months. 11. Manufacturing location KYOCERA Crystal Device Philippines, Inc. 12. Quality Assurance Kyocera Crystal Device Quality Assurance Division 13. Quality guarantee When the failure by the responsibility of our company occurs clearly after delivery within 1 year, a substitute article etc. is appropriated gratuitously and this is guaranteed. However, when passing 1 year after delivery, there is a case where I am allowed to consider as onerous repair after both consultation. 14.Others When any questions and opinions are in the written matter of these delivery specifications, I will ask connection of you from the our company issue day within 45 days. In a connection no case, a written matter is consented to it and employed within a term. KYOCERA Crystal Device Corporation KBS-5079E