F911A476MBAAJ6

F91-AJ6 Series – Automotive Product Range F91-AJ6 Series Low ESR, Resin-Molded Chip - Automotive Product Range FEATURES • Compliant to the RoHS3 directive 2015/863/EU • Compliant to AEC-Q200 • 100% Surge Current Tested LEAD-FREE COMPATIBLE COMPONENT APPLICATIONS • Cabin Electronics • Infotainment CASE DIMENSIONS: millimeters (inches) Code EIA Code EIA Metric L ± 0.20 (0.008) W ± 0.20 (0.008) -0.10 (0.004) H ± 0.20 (0.008) -0.10 (0.004) W1 ± 0.20 (0.008) A ± 0.30 (0.012) -0.20 (0.008) S Min. A 1206 1210 2917 3216-18 3528-21 7343-31 3.20 (0.126) 3.50 (0.138) 7.30 (0.287) 1.60 (0.063) 2.80 (0.110) 4.30 (0.169) 1.60 (0.063) 1.90 (0.075) 2.90 (0.114) 1.20 (0.047) 2.20 (0.087) 2.40 (0.094) 0.80 (0.031) 0.80 (0.031) 1.30 (0.051) 1.10 (0.043) 1.40 (0.055) 4.40 (0.173) B N W1 dimension applies to the termination width for a dimensional area only A, B, N CASE Capacitance Value in pF 476 = 47μF LOGO 4V 6.3V 10V Rated Voltage Code A = 10V ID Code 476 A xxxxx Polarity Band (Anode+) G J A 16V 20V 25V C D E 35V V *Capacitance code of “P” case products are as shown below. HOW TO ORDER F91 1C 226 M B  AJ6 Type Rated Voltage Capacitance Code pF code: 1st two digits represent significant figures, 3rd digit represents multiplier (number of zeros to follow) Tolerance K = ±10% M = ±20% Case Size See table above Packaging See Tape & Reel Packaging Section Tolerance K = ±10% M = ±20% TECHNICAL SPECIFICATIONS Category Temperature Range Rated Temperature Capacitance Tolerance Dissipation Factor ESR 100kHz Leakage Current Capacitance Change By Temperature 88 -55 to +125°C +85°C ±20%, ±10% at 120Hz Refer to next page Refer to next page After 1 minute’s application of rated voltage, leakage current at 20°C is not more than 0.01CV or 0.5μA, whichever is greater. After 1 minute’s application of rated voltage, leakage current at 85°C is not more than 0.1CV or 5μA, whichever is greater. After 1 minute’s application of derated voltage, leakage current at 125°C is not more than 0.125CV or 6.3μA, whichever is greater. +15% Max. at +125°C +10% Max. at +85°C -10% Max. at -55°C The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 090121 – polymer, tantalum and niobium oxide capacitors – F91-AJ6 Series Low ESR, Resin-Molded Chip - Automotive Product Range CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance μF Code 10 106 22 226 33 336 47 476 100 107 220 227 Released ratings 6.3V (0J) A A,B B Rated Voltage 10V (1A) A A B B *1: ΔC/C Marked “*” 16V (1C) A B B Item N N All Case (%) Damp Heat Temperature cycles Resistance soldering heat Surge Endurance ±10 ±10 ±10 ±10 ±10 RATINGS & PART NUMBER REFERENCE Part Number Case Size Capacitance (μF) Rated Voltage (V) DCL (μA) DF @ 120Hz (%) F910J226#AAAJ6 F910J476#AAAJ6 F910J476#BAAJ6 F910J107#BAAJ6 A A B B 22 47 47 100 6.3 6.3 6.3 6.3 1.4 3.0 3.0 6.3 8 18 6 14 F911A106#AAAJ6 F911A226#AAAJ6 F911A336#BAAJ6 F911A476#BAAJ6 F911A227#NCAJ6 A A B B N 10 22 33 47 220 10 10 10 10 10 1.0 2.2 3.3 4.7 22.0 6 12 8 8 12 F911C106#AAAJ6 F911C226#BAAJ6 F911C336#BAAJ6 F911C107#NCAJ6 A B B N 10 22 33 100 16 16 16 16 1.6 3.5 5.3 16.0 6 8 8 10 ESR @ 100kHz (mΩ) 100kHz RMS Current (mA) 25ºC 85ºC 125ºC *1 ΔC/C (%) 1250 1250 500 450 245 245 412 435 220 220 371 391 98 98 165 174 * * * * 3 3 3 3 1500 1250 700 500 100 224 245 348 412 1225 201 220 314 371 1102 89 98 139 165 490 * * * * * 3 3 3 3 3 1500 950 950 100 224 299 299 1225 201 269 269 1102 89 120 120 490 * * * * 3 3 3 3 MSL 6.3 Volt 10 Volt 16 Volt #: "M" for ±20% tolerance, "K" for ± 10% tolerance. Moisture Sensitivity Level (MSL) is defined according to J-STD-020. QUALIFICATION TABLE TEST F91-AJ6 series (Temperature range -55ºC to +125ºC) Condition At 40°C, 90 to 95% R.H., 500 hours (No voltage applied) Capacitance Change ................... Refer to the table above (*1) Dissipation Factor ........................ Initial specified value or less Leakage Current ........................... Initial specified value or less After 1000 hour’s application of rated voltage in series with a 33Ω resistor at 85°C, 85% R.H., capacitors meet the characteristics requirements table below. Capacitance Change ................... Refer to the table above (*1) Load Humidity Dissipation Factor ........................ Initial specified value or less Leakage Current ........................... 125% or less than the initial specified value At -55°C / +125°C, 30 minutes each, 1000 cycles Capacitance Change ................... Refer to the table above (*1) Temperature Cycles Dissipation Factor ........................ Initial specified value or less Leakage Current ........................... Initial specified value or less 10 seconds reflow at 260°C, 10 seconds immersion at 260°C. Capacitance Change ................... Refer to the table above (*1) Resistance to Soldering Heat Dissipation Factor ........................ Initial specified value or less Leakage Current ........................... Initial specified value or less After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above. Capacitance Change .....................Refer to the table above (*1) Surge Dissipation Factor .. ........................Initial specified value or less Leakage Current ............................Initial specified value or less After 2000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C, or derated voltage in series with a 3Ω resistor at 125°C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ................. Refer to the table above (*1) Endurance Dissipation Factor...................... Initial specified value or less Leakage Current ........................ Initial specified value or less After applying the pressure load of 17.7N for 60 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its Shear Test sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified Terminal Strength jig at the center of the substrate so that substrate may bend by1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. 1% per 1000 hours at 85°C, VR with 0.1Ω/V series impedance, Failure Rate 60% confidence level. Damp Heat (Steady State) The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 040120 – polymer, tantalum and niobium oxide capacitors – 89 F91-AJ6 Series Low ESR, Resin-Molded Chip - Automotive Product Range SOLID ELECTROLYTIC CAPACITOR ROADMAP SERIES LINE UP : CONVENTIONAL SMD MnO2 TMJ High Rel. & Special High Temp THH ultra low DCL THJ 200°C THJ F97-HT3 175°C auto 135°C auto TRM TRJ Industrial & Automotive 230°C COTS+ Hermetic professional multianode professional TAJ F91-AJ6 auto TPS auto *T/*U F93-AJ6 auto *T/*U TPS F97 professional auto F98-AJ6 auto TPM multianode Standard TAJ Standard Low Profile High CV 90 TAJ TLN undertab F91 TAC Low Profile microchip TLJ microchip TPC microchip F93 Low ESR F98-AS1 TLC undertab, fused F92 F98 undertab The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 030321 – polymer, tantalum and niobium oxide capacitors –