F911C476MNC

F91 Series F91 Series Low ESR, Resin-Molded Chip J-Lead FEATURES • • • • Compliant to the RoHS3 directive 2015/863/EU SMD J-Lead Low ESR 100% Surge Current Tested LEAD-FREE COMPATIBLE COMPONENT APPLICATIONS • General Medium Power DC/DC Convertors CASE DIMENSIONS: millimeters (inches) Code EIA Code EIA Metric L ± 0.20 (0.008) W ± 0.20 (0.008) -0.10 (0.004) H ± 0.20 (0.008) -0.10 (0.004) W1 ± 0.20 (0.008) A ± 0.30 (0.012) -0.20 (0.008) S Min. B C N 1210 2312 2917 3528-21 6032-28 7343-31 3.50 (0.138) 6.00 (0.236) 7.30 (0.287) 2.80 (0.110) 3.20 (0.126) 4.30 (0.169) 1.90 (0.075) 2.60 (0.102) 2.90 (0.114) 2.20 (0.087) 2.20 (0.087) 2.40 (0.094) 0.80 (0.031) 1.30 (0.051) 1.30 (0.051) 1.40 (0.055) 2.90 (0.114) 4.40 (0.173) W1 dimension applies to the termination width for a dimensional area only B, C, N CASE Capacitance Value in pF 476 = 47μF LOGO 4V 6.3V 10V Rated Voltage Code A = 10V ID Code 476 A xxxxx Polarity Band (Anode+) G J A 16V 20V 25V C D E 35V V *Capacitance code of “P” case products are as shown below. HOW TO ORDER F91 1A Type Rated Voltage 107 M C Capacitance Code Tolerance Case Size pF code: 1st two digits represent significant figures, 3rd digit represents multiplier (number of zeros to follow) K = ±10% M = ±20% ⃣ See table above Packaging See Tape & Reel Packaging Section TECHNICAL SPECIFICATIONS Category Temperature Range Rated Temperature Capacitance Tolerance Dissipation Factor ESR 100kHz Leakage Current Capacitance Change By Temperature 84 -55 to +125°C +85°C ±20%, ±10% at 120Hz Refer to next page Refer to next page After 1 minute’s application of rated voltage, leakage current at 20°C is not more than 0.01CV or 0.5μA, whichever is greater. After 1 minute’s application of rated voltage, leakage current at 85°C is not more than 0.1CV or 5μA, whichever is greater. After 1 minute’s application of derated voltage, leakage current at 125°C is not more than 0.125CV or 6.3μA, whichever is greater. +15% Max. at +125°C +10% Max. at +85°C -10% Max. at -55°C The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 090121 – polymer, tantalum and niobium oxide capacitors – F91 Series Low ESR, Resin-Molded Chip J-Lead CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance μF Code 6.8 685 10 106 15 156 22 226 33 336 47 476 68 686 100 107 150 157 220 227 330 337 470 477 680 687 Released ratings Rated Voltage 4V (0G) 6.3V (0J) 10V (1A) 20V (1D) 25V (1E) C C B B/C N B C C N N N C C C/N N N C C N N N 16V (1C) N N N N 35V (1V) C N N N N RATINGS & PART NUMBER REFERENCE Part Number Case Size Capacitance (μF) Rated Voltage (V) DCL (μA) F910G157#CC F910G227#CC F910G337#NC F910G477#NC F910G687#NC C C N N N 150 220 330 470 680 4 4 4 4 4 6.0 8.8 13.2 18.8 27.2 F910J107#CC F910J157#CC F910J227#CC F910J227#NC F910J337#NC F910J477#NC C C C N N N 100 150 220 220 330 470 6.3 6.3 6.3 6.3 6.3 6.3 6.3 9.5 13.9 13.9 20.8 29.6 F911A476#BA F911A686#CC F911A107#CC F911A157#NC F911A227#NC F911A337#NC B C C N N N 47 68 100 150 220 330 10 10 10 10 10 10 4.7 6.8 10.0 15.0 22.0 33.0 F911C226#BA F911C336#BA F911C336#CC F911C476#NC F911C107#NC B B C N N 22 33 33 47 100 16 16 16 16 16 3.5 5.3 5.3 7.6 16 F911D156#CC F911D476#NC C N 15 47 20 20 3 9.4 F911E106#CC F911E226#NC F911E336#NC F911E476#NC C N N N 10 22 33 47 25 25 25 25 2.5 5.5 8.3 11.8 F911V685#CC F911V106#NC F911V156#NC F911V226#NC C N N N 6.8 10 15 22 35 35 35 35 2.4 3.5 5.3 7.7 DF @ 120Hz (%) ESR @ 100kHz (mΩ) 25ºC 85ºC 125ºC 12 12 10 16 18 250 250 100 100 100 663 663 1225 1225 1225 597 597 1102 1102 1102 265 265 490 490 490 1 1 1 1 1 8 12 14 10 14 16 250 250 250 100 100 100 663 663 663 1225 1225 1225 597 597 597 1102 1102 1102 265 265 265 490 490 490 1 1 1 1 1 1 8 8 10 10 12 18 500 300 250 100 100 100 412 606 663 1225 1225 1225 371 545 597 1102 1102 1102 165 242 265 490 490 490 1 1 1 1 3 3 8 8 6 6 10 950 950 400 150 100 299 299 524 1000 1225 269 269 472 900 1102 120 120 210 400 490 1 1 1 1 3 6 8 450 200 494 866 445 779 198 346 1 1 6 6 8 8 450 200 200 250 494 866 866 775 445 779 779 697 198 346 346 310 1 1 1 1 6 6 6 8 600 300 300 300 428 707 707 707 385 636 636 636 171 283 283 283 1 1 1 1 100kHz RMS Current (mA) MSL 4 Volt 6.3 Volt 10 Volt 16 Volt 20 Volt 25 Volt 35 Volt #: "M" for ±20% tolerance, "K" for ± 10% tolerance. Moisture Sensitivity Level (MSL) is defined according to J-STD-020. The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 022421 – polymer, tantalum and niobium oxide capacitors – 85 F91 Series Low ESR, Resin-Molded Chip J-Lead QUALIFICATION TABLE TEST Damp Heat (Steady State) Temperature Cycles Resistance to Soldering Heat Surge Endurance Shear Test Terminal Strength 86 F91 series (Temperature range -55ºC to +125ºC) Condition At 40°C, 90 to 95% R.H., 500 hours (No voltage applied) Capacitance Change ............ Within ±10% of the initial value Dissipation Factor ................. Initial specified value or less Leakage Current .................... Initial specified value or less -55°C / +125°C, 30 minutes each, 5 cycles Capacitance Change ............ Within ±5% of the initial value Dissipation Factor ................. Initial specified value or less Leakage Current .................... Initial specified value or less 10 seconds reflow at 260°C, 5 seconds immersion at 260°C. Capacitance Change ............ Within ±5% of the initial value Dissipation Factor ................. Initial specified value or less Leakage Current .................... Initial specified value or less After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ............ Within ±5% of the initial value Dissipation Factor ................. Initial specified value or less Leakage Current .................... Initial specified value or less After 2000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C, or derated voltage in series with a 3Ω resistor at 125°C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ..............Within ±10% of the initial value Dissipation Factor .. ................. Initial specified value or less Leakage Current ..................... Initial specified value or less After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 040120 – polymer, tantalum and niobium oxide capacitors – F91 Series Low ESR, Resin-Molded Chip J-Lead SOLID ELECTROLYTIC CAPACITOR ROADMAP SERIES LINE UP : CONVENTIONAL SMD MnO2 TMJ High Rel. & Special High Temp THH ultra low DCL THJ 200°C THJ F97-HT3 175°C auto 135°C auto TRM TRJ Industrial & Automotive 230°C COTS+ Hermetic professional multianode professional TAJ F91-AJ6 auto TPS auto *T/*U F93-AJ6 auto *T/*U TPS F97 professional auto F98-AJ6 auto TPM multianode Standard TAJ Standard Low Profile High CV TAJ TLN undertab F91 TAC Low Profile microchip TLJ microchip TPC microchip F93 Low ESR F98-AS1 TLC undertab, fused F92 F98 undertab The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 030321 – polymer, tantalum and niobium oxide capacitors – 87