F950G227MTAAM1Q

F95 Audio Series – Optimized for Audio Applications F95 Audio Series Conformal Coated Chip Optimized for Audio Applications FEATURES • • • • • • • • • L W H Solder electrode Solder electrode A B Mobile Audio Player Smartphone Mobile Phone Wireless Microphone System (D) C CASE DIMENSIONS: Single-side electrodes (Both electrodes at bottom side only) MARKING S CASE LEAD-FREE COMPATIBLE COMPONENT APPLICATIONS • • • • Resin Compliant to the RoHS3 directive 2015/863/EU Rich Sound in the Bass Register and Clear Sound Materials are Strictly Selected to Achieve High Level Sound F95 Series has No Lead-Frame and No Vibration Factor Low ESR, Low ESL 100% Surge Current Tested Line Up Miniature Size and High Capacitance, Necessary to Mobile Design SMD Conformal Small and High CV B, T CASE J8 J8 Capacitance Code millimeters (inches) Code EIA Code EIA Metric L W H A B C D* B 1411 3528-20 3.50±0.20 (0.138±0.008) 2.80±0.20 (0.110±0.008) 1.80±0.20 (0.071±0.008) 0.80±0.30 (0.031±0.012) 1.20±0.30 (0.047±0.012) 1.10±0.30 (0.043±0.012) 0.20 (0.008) S 1306 3216-12 3.20±0.30 (0.126±0.012) 1.60±0.30 (0.063±0.012) 1.00±0.20 (0.039±0.008) 0.80±0.30 (0.031±0.012) 1.20±0.30 (0.047±0.012) 0.80±0.30 (0.031±0.012) 0.20 (0.008) T 1411 3527-12 3.50±0.20 (0.138±0.008) 2.70±0.20 (0.106±0.008) 1.00±0.20 (0.039±0.008) 0.80±0.20 (0.031±0.008) 1.20±0.20 (0.047±0.008) 1.10±0.20 (0.043±0.012) 0.20 (0.008) *D dimension only for reference Capacitance Code μF 68 100 150 220 330 470 680 code W7 A8 E8 J8 N8 S8 W8 HOW TO ORDER F95 0G 227 M S  AM1 Q2 Type Rated Voltage Capacitance Code pF code: 1st two digits represent significant figures, 3rd digit represents multiplier (number of zeros to follow) Tolerance K=±10% M=±20% Case Size See table above Packaging See Tape & Reel Packaging Section AUDIO Series Code Single Face Electrode TECHNICAL SPECIFICATIONS Category Temperature Range: Rated Temperature: Capacitance Tolerance: Dissipation Factor: ESR 100kHz: Leakage Current: Capacitance Change By Temperature -55 to +125°C +85°C ±20%, ±10% at 120Hz Refer to next page Refer to next page Refer to next page Provided that: After 1 minute’s application of rated voltage, leakage current at 85°C 10 times or less than 20ºC specified value. After 1 minute’s application of rated voltage, leakage current at 125°C 12.5 times or less than 20ºC specified value. +15% Max. at +125°C +10% Max. at +85°C -10% Max. at -55°C The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 102220 – polymer, tantalum and niobium oxide capacitors – 157 F95 Audio Series Conformal Coated Chip Optimized for Audio Applications CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance μF 68 100 150 220 330 470 680 Code 686 107 157 227 337 477 687 4V (0G) S S S S/T T B Rated Voltage 6.3V (0J) 10V (1A) S B S/T B B B Released ratings Please contact to your local KYOCERA AVX sales office when these series are being designed in your application. RATINGS & PART NUMBER REFERENCE Part Number Case Size Capacitance (μF) Rated Voltage (V) DCL (μA) DF @ 120Hz (%) F950G686#SAAM1Q2 F950G107#SAAM1Q2 F950G157#SAAM1Q2 F950G227#SAAM1Q2 F950G227#TAAM1Q2 F950G337#TAAM1Q2 F950G477#BAAM1Q2 S S S S T T B 68 100 150 220 220 330 470 4 4 4 4 4 4 4 2.7 4.0 6.0 8.8 8.8 13.2 18.8 10 14 22 30 25 40 40 F950J686#SAAM1Q2 F950J107#SAAM1Q2 F950J107#TAAM1Q2 F950J227#BAAM1Q2 F950J337#BAAM1Q2 S S T B B 68 100 100 220 330 6.3 6.3 6.3 6.3 6.3 4.3 6.3 6.3 13.9 20.8 14 20 14 30 35 F951A686#BAAM1Q2 F951A107#BAAM1Q2 B B 68 100 10 10 6.8 10.0 12 14 100kHz RMS Current (mA) ESR @ 100kHz (Ω) 25ºC 85ºC 125ºC *1 ΔC/C (%) MSL 0.8 0.8 0.8 0.8 0.6 0.8 0.4 274 274 274 274 365 316 461 246 246 246 246 329 285 415 110 110 110 110 146 126 184 * * ±15 ±15 * ±20 ±20 3 3 3 3 3 3 3 0.9 0.9 0.6 0.4 0.6 258 258 365 461 376 232 232 329 415 339 103 103 146 184 151 * ±15 * * ±20 3 3 3 3 3 0.4 0.4 461 461 415 415 184 184 * * 3 3 4 Volt 6.3 Volt 10 Volt *1: ΔC/C Marked “*” Item Damp Heat Temperature cycles Resistance soldering heat Surge Endurance 158 #: "M" for ±20% tolerance, "K" for ± 10% tolerance. Moisture Sensitivity Level (MSL) is defined according to J-STD-020. All Case (%) ±10 ±5 ±5 ±5 ±10 The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 040720 – polymer, tantalum and niobium oxide capacitors – F95 Audio Series Conformal Coated Chip Optimized for Audio Applications QUALIFICATION TABLE Audio F95 series (Temperature range -55ºC to +125ºC) TEST Condition Damp Heat (Steady State) At 40°C, 90 to 95% R.H., 500 hours (No voltage applied) Capacitance Change ................... Refer to the table above (*1) Dissipation Factor ........................ Initial specified value or less Leakage Current ........................... Initial specified value or less Temperature Cycles At -55°C / +125°C, 30 minutes each, 5 cycles Capacitance Change ................... Refer to the table above (*1) Dissipation Factor ........................ Initial specified value or less Leakage Current ........................... Initial specified value or less Resistance to Soldering Heat 10 seconds reflow at 260°C, 5 seconds immersion at 260°C. Capacitance Change ................... Refer to the table above (*1) Dissipation Factor ........................ Initial specified value or less Leakage Current ........................... Initial specified value or less Surge After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ................... Refer to the table above (*1) Dissipation Factor ........................ Initial specified value or less Leakage Current ........................... Initial specified value or less Endurance After 2000 hours’ application of rated voltage 85°C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ..................... Refer to the table above (*1) Dissipation Factor .. ........................ Initial specified value or less Leakage Current ............................ Initial specified value or less Shear Test After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Terminal Strength Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. SERIES LINE UP : SOLID ELECTROLYTIC CAPACITOR ROADMAP CONVENTIONAL SMD MnO2 The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 122920 – polymer, tantalum and niobium oxide capacitors – 159