F981A226MSAAS1

F98-AS1 Series – Fused Tantalum Chip - Undertab F98-AS1 Series Fused Face-Down, High CV FEATURES • • • • Compliant to the RoHS3 directive 2015/863/EU SMD Face Down Design Small and Low Profile 100% Surge Current Tested LEAD-FREE COMPATIBLE COMPONENT APPLICATIONS • • • • Smartphone Mobile Phone Wireless Module Hearing Aid CASE DIMENSIONS: millimeters (inches) Code EIA Code S 0805 EIA Metric L 2012-09 2.00 -0.10 (0.079 +0.008 -0.004 ) L +0.20 W1 +0.20 1.25 -0.10 (0.049 +0.008 -0.004 ) S1 S2 0.50±0.10 (0.020±0.004) 1.00±0.10 (0.039±0.004) S CASE An W2 S2 H 0.80±0.10 (0.031±0.004) MARKING W1 H S1 W2 0.90±0.10 (0.035±0.004) *Capacitance Code Rated Voltage Code S1 HOW TO ORDER F98 1A 336 M S  AS1 Type Rated Voltage Capacitance Code pF code: 1st two digits represent significant figures, 3rd digit represents multiplier (number of zeros to follow) Tolerance M = ±20% Case Size See table above Packaging Fuse Series Code Reel Dia (φ180) A Tape Width (mm) 8 TECHNICAL SPECIFICATIONS Category Temperature Range: Rated Temperature: Capacitance Tolerance: Dissipation Factor: ESR 100kHz: Leakage Current: Termination Finish: 58 -55 to +125°C +85°C ±20% at 120Hz Refer to next page Refer to next page Refer to next page Provided that: After 5 minute’s application of rated voltage, leakage current at 85°C 10 times or less than 20ºC specified value. After 5 minute’s application of rated voltage, leakage current at 125°C 12.5 times or less than 20ºC specified value. Gold Plating (standard) The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 102020 – polymer, tantalum and niobium oxide capacitors – F98-AS1 Series Fused Face-Down, High CV CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance μF Code 1.0 105 2.2 225 4.7 475 10 106 22 226 33 336 47 476 10V (1A) Rated Voltage 20V (1D) 16V (1C) 25V (1E) *Cap Code 35 (1V) S A J S a j n s S S S S Released ratings Please contact to your local KYOCERA AVX sales office when these series are being designed in your application. RATINGS & PART NUMBER REFERENCE Part Number Case Size Capacitance (μF) Rated Voltage (V) DCL (μA) DF @ 120Hz (%) F981A226MSAAS1 F981A336MSAAS1 F981A476MSAAS1 S S S 22 33 47 10 10 10 2.2 3.3 9.4 20 30 35 F981C106MSAAS1 S 10 16 1.6 18 F981V105MSAAS1 S 1 35 0.7 *2: Leakage Current After 5 minute’s application of rated voltage, leakage current at 20ºC. 20 100kHz RMS Current (mA) ESR @ 100kHz (Ω) 10 Volt 16 Volt 35 Volt 25ºC 85ºC 125ºC *1 ΔC/C (%) MSL 4.5 6.5 5.5 100 83 90 90 75 81 40 33 36 ±20 ±30 ±30 3 3 3 4.5 100 90 40 ±20 3 73 65 29 ±30 3 8.5 Moisture Sensitivity Level (MSL) is defined according to J-STD-020. QUALIFICATION TABLE TEST F98-AS1 series (Temperature range -55ºC to +125ºC) Condition Damp Heat (Steady State) At 40°C, 90 to 95% R.H., 500 hours (No voltage applied) Capacitance Change ............ Refer to the table above (*1) Dissipation Factor ................. 150% or less of initial specified value Leakage Current .................... 200% or less of initial specified value Temperature Cycles -55°C / +125°C, 30 minutes each, 5 cycles Capacitance Change ............ Refer to the table above (*1) Dissipation Factor ................. 150% or less of initial specified value Leakage Current .................... 200% or less of initial specified value Resistance to Soldering Heat Surge Endurance Shear Test Terminal Strength Fuse Activation 10 seconds reflow at 260°C, 5 seconds immersion at 260°C. Capacitance Change ............ Refer to the table above (*1) Dissipation Factor ................. Initial specified value or less Leakage Current .................... Initial specified value or less After application of surge in series with a 1kΩ resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ............ Refer the table above (*1) Dissipation Factor ................. 150% or less of initial specified value Leakage Current .................... 200% or less of initial specified value After 1000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ..............Refer to the table above (*1) Dissipation Factor .. .................150% or less of initial specified value Leakage Current .....................200% or less of initial specified value After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side bodywhich has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. 5 seconds max. with 2A min. applied current The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 063021 – polymer, tantalum and niobium oxide capacitors – 59 F98-AS1 Series Fused Face-Down, High CV SOLID ELECTROLYTIC CAPACITOR ROADMAP SERIES LINE UP: CONVENTIONAL SMD MnO2 TMJ High Rel. & Special High Temp THH ultra low DCL THJ 200°C THJ F97-HT3 175°C auto 135°C auto TRM TRJ Industrial & Automotive 230°C COTS+ Hermetic professional multianode professional TAJ F91-AJ6 auto TPS auto *T/*U F93-AJ6 auto *T/*U TPS F97 professional auto F98-AJ6 auto TPM multianode Standard TAJ Standard Low Profile High CV 60 TAJ TLN undertab F91 TAC Low Profile microchip TLJ microchip TPC microchip F93 Low ESR F98-AS1 TLC undertab, fused F92 F98 undertab The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 030321 – polymer, tantalum and niobium oxide capacitors –