F98-AS1 Series – Fused Tantalum Chip - Undertab
F98-AS1 Series
Fused Face-Down, High CV
FEATURES
•
•
•
•
Compliant to the RoHS3 directive 2015/863/EU
SMD Face Down Design
Small and Low Profile
100% Surge Current Tested
LEAD-FREE COMPATIBLE
COMPONENT
APPLICATIONS
•
•
•
•
Smartphone
Mobile Phone
Wireless Module
Hearing Aid
CASE DIMENSIONS: millimeters (inches)
Code
EIA Code
S
0805
EIA Metric
L
2012-09
2.00 -0.10
(0.079 +0.008
-0.004 )
L
+0.20
W1
+0.20
1.25 -0.10
(0.049 +0.008
-0.004 )
S1
S2
0.50±0.10
(0.020±0.004)
1.00±0.10
(0.039±0.004)
S CASE
An
W2
S2
H
0.80±0.10
(0.031±0.004)
MARKING
W1
H
S1
W2
0.90±0.10
(0.035±0.004)
*Capacitance
Code
Rated Voltage
Code
S1
HOW TO ORDER
F98
1A
336
M
S
AS1
Type
Rated
Voltage
Capacitance
Code
pF code: 1st two digits
represent significant figures,
3rd digit represents multiplier
(number of zeros to follow)
Tolerance
M = ±20%
Case
Size
See
table
above
Packaging
Fuse Series
Code
Reel Dia
(φ180)
A
Tape Width
(mm)
8
TECHNICAL SPECIFICATIONS
Category Temperature Range:
Rated Temperature:
Capacitance Tolerance:
Dissipation Factor:
ESR 100kHz:
Leakage Current:
Termination Finish:
58
-55 to +125°C
+85°C
±20% at 120Hz
Refer to next page
Refer to next page
Refer to next page
Provided that:
After 5 minute’s application of rated voltage, leakage current at 85°C
10 times or less than 20ºC specified value.
After 5 minute’s application of rated voltage, leakage current at 125°C
12.5 times or less than 20ºC specified value.
Gold Plating (standard)
The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available
online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.
102020
– polymer, tantalum and niobium oxide capacitors –
F98-AS1 Series
Fused Face-Down, High CV
CAPACITANCE AND RATED VOLTAGE RANGE
(LETTER DENOTES CASE SIZE)
Capacitance
μF
Code
1.0
105
2.2
225
4.7
475
10
106
22
226
33
336
47
476
10V (1A)
Rated Voltage
20V (1D)
16V (1C)
25V (1E)
*Cap Code
35 (1V)
S
A
J
S
a
j
n
s
S
S
S
S
Released ratings
Please contact to your local KYOCERA AVX sales office when these series are being designed in your application.
RATINGS & PART NUMBER REFERENCE
Part Number
Case
Size
Capacitance
(μF)
Rated
Voltage
(V)
DCL
(μA)
DF
@ 120Hz
(%)
F981A226MSAAS1
F981A336MSAAS1
F981A476MSAAS1
S
S
S
22
33
47
10
10
10
2.2
3.3
9.4
20
30
35
F981C106MSAAS1
S
10
16
1.6
18
F981V105MSAAS1
S
1
35
0.7
*2: Leakage Current
After 5 minute’s application of rated voltage, leakage current at 20ºC.
20
100kHz RMS Current (mA)
ESR
@ 100kHz
(Ω)
10 Volt
16 Volt
35 Volt
25ºC
85ºC
125ºC
*1
ΔC/C
(%)
MSL
4.5
6.5
5.5
100
83
90
90
75
81
40
33
36
±20
±30
±30
3
3
3
4.5
100
90
40
±20
3
73
65
29
±30
3
8.5
Moisture Sensitivity Level (MSL) is defined according to J-STD-020.
QUALIFICATION TABLE
TEST
F98-AS1 series (Temperature range -55ºC to +125ºC)
Condition
Damp Heat
(Steady State)
At 40°C, 90 to 95% R.H., 500 hours (No voltage applied)
Capacitance Change ............ Refer to the table above (*1)
Dissipation Factor ................. 150% or less of initial specified value
Leakage Current .................... 200% or less of initial specified value
Temperature Cycles
-55°C / +125°C, 30 minutes each, 5 cycles
Capacitance Change ............ Refer to the table above (*1)
Dissipation Factor ................. 150% or less of initial specified value
Leakage Current .................... 200% or less of initial specified value
Resistance to
Soldering Heat
Surge
Endurance
Shear Test
Terminal Strength
Fuse Activation
10 seconds reflow at 260°C, 5 seconds immersion at 260°C.
Capacitance Change ............ Refer to the table above (*1)
Dissipation Factor ................. Initial specified value or less
Leakage Current .................... Initial specified value or less
After application of surge in series with a 1kΩ resistor at the rate of 30 seconds ON, 30 seconds OFF,
for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above.
Capacitance Change ............ Refer the table above (*1)
Dissipation Factor ................. 150% or less of initial specified value
Leakage Current .................... 200% or less of initial specified value
After 1000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C,
capacitors shall meet the characteristic requirements in the table above.
Capacitance Change ..............Refer to the table above (*1)
Dissipation Factor .. .................150% or less of initial specified value
Leakage Current .....................200% or less of initial specified value
After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side
bodywhich has no electrode and has been soldered beforehand on a substrate, there shall be found
neither exfoliation nor its sign at the terminal electrode.
Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at
both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength
is applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as
illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals.
5 seconds max. with 2A min. applied current
The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available
online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.
063021
– polymer, tantalum and niobium oxide capacitors –
59
F98-AS1 Series
Fused Face-Down, High CV
SOLID ELECTROLYTIC CAPACITOR ROADMAP
SERIES LINE UP: CONVENTIONAL SMD MnO2
TMJ
High Rel.
& Special
High Temp
THH
ultra
low DCL
THJ
200°C
THJ
F97-HT3
175°C auto
135°C auto
TRM
TRJ
Industrial &
Automotive
230°C COTS+
Hermetic
professional
multianode
professional
TAJ
F91-AJ6
auto
TPS
auto *T/*U
F93-AJ6
auto *T/*U
TPS
F97
professional
auto
F98-AJ6
auto
TPM
multianode
Standard
TAJ
Standard
Low Profile
High CV
60
TAJ
TLN
undertab
F91
TAC
Low Profile
microchip
TLJ
microchip
TPC
microchip
F93
Low ESR
F98-AS1
TLC
undertab,
fused
F92
F98
undertab
The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available
online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.
030321
– polymer, tantalum and niobium oxide capacitors –
很抱歉,暂时无法提供与“F981C106MSAAS1”相匹配的价格&库存,您可以联系我们找货
免费人工找货