KGM02AR50J103KH

X5R Dielectric General Specifications GENERAL DESCRIPTION • General Purpose Dielectric for Ceramic Capacitors • EIA Class II Dielectric • Temperature variation of capacitance is within ±15% from -55°C to +85°C • Well suited for decoupling and filtering applications • Available in High Capacitance values (up to 100μF) PART NUMBER (SEE PAGE 4 FOR COMPLETE PART NUMBER EXPLANATION) 1210 4 D Size Voltage (L” x W”) 4 = 4V 0101** 6 = 6.3V 0201 Z = 10V 0402 Y = 16V 0603 3 = 25V 0805 D = 35V 1206 5 = 50V 1210 1 = 100V 1812 **EIA 01005 107 Dielectric D = X5R Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros M A T 2 A Capacitance Tolerance K = ±10% M = ± 20% Failure Rate A = N/A Terminations T = Plated Ni and Sn Packaging 2 = 7” Reel 4 = 13” Reel Special Code A = Std. NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. Insulation Resistance (Ohm-Farads) TYPICAL ELECTRICAL CHARACTERISTICS 20 15 % Capacitance 10 0 -5 -10 -15 -20 -60 -40 -20 0 +20 +40 +60 +80 Temperature °C 26 10,000 Insulation Resistance vs Temperature 1,000 100 0 20 40 60 80 Temperature °C The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. TDS-SMDMLCC-0014 | Rev 1 – surface mount ceramic capacitor products – 100 120 X5R Dielectric Specifications and Test Methods Parameter/Test Operating Temperature Range Capacitance X5R Specification Limits -55ºC to +85ºC Within specified tolerance Measuring Conditions Temperature Cycle Chamber Dissipation Factor ≤ 2.5% for ≥ 50V DC rating ≤ 12.5% for 25V, 35V DC rating ≤ 12.5% Max. for 16V DC rating and lower Contact Factory for DF by PN Freq.: 1.0 kHz ± 10% Voltage: 1.0Vrms ± .2V For Cap > 10 µF, 0.5Vrms @ 120Hz Insulation Resistance 10,000MΩ or 500MΩ - µF, whichever is less Charge device with rated voltage for 120 ± 5 secs @ room temp/humidity Dielectric Strength No breakdown or visual defects Charge device with 250% of rated voltage for 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Appearance Resistance to Flexure Stresses No defects Capacitance Variation Dissipation Factor Insulation Resistance Capacitance Variation Dissipation Factor ≤ ±7.5% Meets Initial Values (As Above) Insulation Resistance Meets Initial Values (As Above) Dielectric Strength Meets Initial Values (As Above) Appearance No visual defects Capacitance Variation Dissipation Factor Dissipation Factor Dip device in eutectic solder at 260ºC for 60seconds. Store at room temperature for 24 ± 2hours before measuring electrical properties. Step 1: -55ºC ± 2º 30 ± 3 minutes ≤ ±7.5% Step 2: Room Temp ≤ 3 minutes Meets Initial Values (As Above) Step 3: +85ºC ± 2º 30 ± 3 minutes Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutes Meets Initial Values (As Above) Repeat for 5 cycles and measure after 24 ± 2 hours at room temperature No visual defects Capacitance Variation Load Humidity Dip device in eutectic solder at 230 ± 5ºC for 5.0 ± 0.5 seconds No defects,