KGM05AR51C104KH

X5R Dielectric, KGM Series General Specifications GENERAL DESCRIPTION • General Purpose Dielectric for Ceramic Capacitors • EIA Class II Dielectric • Temperature variation of capacitance is within ±15% from -55°C to +85°C • Well suited for decoupling and filtering applications • Available in High Capacitance values (up to 100μF) HOW TO ORDER KGM 03 A R5 1E 101 M N Series General Purpose Tin/Nickel Finish Size 02 = 01005 03 = 0201 05 = 0402 15 = 0603 21 = 0805 31 = 1206 32 = 1210 43 = 1812 Thickness See Cap Chart Dielectric R5 = X5R Voltage 0G = 4.0V 0J = 6.3V 1A = 10V 1C = 16V 1V = 35V 1E = 25V 1H = 50V Capacitance Code Code (in pF) Capacitance Tolerance Packaging See Table Below Two Significant Digits + Number of zeroes eg. 106 = 10uF 103 = 10nF 470 = 47pF J* = +/- 5% K = +/- 10% M = +/- 20% NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. PACKAGING CODES Code EIA (inch) IEC(mm) 7" Paper 7" Embossed 13" Paper 13" Embossed 02 01005 0402 H P N 03 0201 0603 H 05 0402 1005 H N 15 0603 1608 T M 21 0805 2012 U L 31 1206 3216 U L 32 1210 3225 U L 43 1812 4532 V S N 20 15 % Capacitance 10 0 -5 -10 -15 -20 -60 -40 -20 0 +20 +40 Temperature °C 22 +60 +80 Insulation Resistance (Ohm-Farads) TYPICAL ELECTRICAL CHARACTERISTICS 10,000 Insulation Resistance vs Temperature 1,000 100 0 20 40 60 80 Temperature °C The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. TDS-SMDMLCC-0035 | Rev 5 – surface mount ceramic capacitor products – 100 120 X5R Dielectric, KGM Series Specifications and Test Methods X5R Specification Limits X5R Specification Limits Operating Temperature Range -55ºC to +85ºC Capacitance Within specified tolerance Measuring Conditions (Complies with JIS C5101 / IEC60384) Temperature Cycle Chamber Measure after heat treatment Capacitance Frequency Volt C≤10µF Frequency : 1kHz±10% Volt : 1.0±0.2Vrms *0.5±0.2Vrms * :KGM02AR50J104, KGM02AR50J474, KGM03CR50J225, KGM03BR50J225 Dissipation Factor / Tanδ Refer to https://spicat.kyocera-avx.com for individual part number specification KGM03DR50J475, KGM03CR50G475, KGM05CR50J106 C>10µF Frequency : 120Hz±10% Volt : 0.5±0.2Vrms The charge and discharge current of the capacitor must not exceed 50mA. Insulation Resistance Refer to https://spicat.kyocera-avx.com for individual part number specifiction Dielectric Strength No breakdown or visual defects Bending Strength No significant damage with 1mm bending Solderability Solder coverage : 95% min. Resistance to Solder Heat Appearance No problem observed Capacitance Variation ≤ ±7.5% Dissipation Factor / Tanδ Within specification Insulation Resistance Within specification Apply the rated voltage for 1 minute, and measure it in normal temperature and humidity. The charge and discharge current of the capacitor must not exceed 50mA. Charge device with 250% of rated voltage for 1-5 seconds, w/ charge and discharge current limited to 50 mA (max) * KGM31AR52A225: 200% of rated voltage Glass epoxy PCB: Fulcrum spacing: 90mm, duration time 10 seconds. Soaking condition Sn-3Ag-0.5Cu 245±5ºC 3±0.5 sec. Take the initial value after heat treatment. Soak the sample in 260ºC±5ºC solder for 10±0.5 seconds and place in nor- mal temperature and humidity, and measure after heat treatment. (Pre-heating conditions) Order 　　　Temperature 　　　　　　　　　Time 　　1 　 　 　80 to 100ºC 　　　　　　　　　2 minutes 　 2　 Withstanding Voltage / Dielectric Resist without problem Strength 150 to 200ºC 　　　　 　　　 2 minutes The charge and discharge current of the capacitor must not exceed 50mA for IR and withstanding voltage measurement. Appearance No visual defects Take the initial value after heat treatment. Capacitance Variation ≤ ±7.5% Room temperature (3 min.) ―> 　 Dissipation Factor Within specification Insulation Resistance Within specification (Cycle) Thermal Shock Withstanding Voltage / Dielectric Room temperature (3 min.) ―> 　 Highest operation temperature (30 min.) After 5 cycles, measure after heat treatment. Resist without problem Strength Load Life Lowest operation temperature (30 min.) ―> 　 Appearance No visual defects Capacitance Variation ≤ ±12.5% The charge and discharge current of the capacitor must not exceed 50mA for IR and withstanding voltage measurement. Take the initial value after heat treatment. After applying *1.5 the rated voltage at the highest operation temperature for 1000+12/ −0 hours, and measure the sample after heat treatment in normal temperature and humidity. The charge and discharge current of the capacitor must not exceed 50mA for IR measurement. Dissipation Factor / Tanδ ≤ Initial Value x 2.0 (See Above) Over 1000MΩ or 50MΩ・µF, whichever is less. *Exceptions Listed Below in the chart below. Appearance No visual defects Take the initial value after heat treatment. Capacitance Variation Load Humidity *Apply 1.0 times when the rated voltage is 4V or less. Applied voltages for respective products are indicated Insulation Resistance After applying rated voltage for 500+12/ −0 hours in the condition of 40ºC±2ºC and 90 to 95%RH, and place in normal ≤ ±12.5% Dissipation Factor / Tanδ Within specification temperature and humidity, then measure the sample after heat treatment. Insulation Resistance Over 1000MΩ or 50MΩ · µF, whichever is less. *Exceptions Listed Below The charge and discharge current of the capacitor must not exceed 50mA for IR measurement. Appearance No problem observed Microscope Termination Strength No problem observed Apply a sideward force of 500g (5N) to a PCB-mounted sample. note : 2N for 0201 size, and 1N for 01005 size. Appearance No problem observed Take the initial value after heat treatment. Capacitance Within tolerance Vibration frequency: 10 to 55 (Hz) Vibration Tanδ Heat treatment Within tolerance Amplitude: 1.5mm Sweeping condition: 10 ―> 55 ―> 10Hz/ 1 minute in X, Y and Z directions: 2 hours each, 6 hours in total, and place in normal temperature and humidity, then measure the sample after heat treatment. Expose sample in the temperature of 150+0/ −10ºC for 1 hour and leave the sample in normal temperature and humidity for 24±2 hours. Voltage to be applied in the High Temperature Load (Applied voltage is the multiple of the rated voltage) Rated Voltage ×1.0 ×1.2 ×1.3 Products 6.3V KGM02AR50J224, KGM02AR50J474, KGM03BR50J225, KGM03CR50J225, KGM03DR50J475, KGM05CR50J106, KGM05BR50J156, KGM05DR50J226, KGM21AR50J476 10V KGM02AR51A104, KGM03CR51A225, KGM15CR51A226 16V KGM03CR51C105, KGM05AR51C225, KGM05CR51C475, KGM15CR51C226 25V KGM05AR51E105, KGM05AR51E225, KGM05CR51E225, KGM05CR51E475, KGM15CR51E475, KGM15CR51E106, KGM21AR51E226 35V KGM05AR51V105, KGM15CR51V475, KGM15CR51V106 100V KGM31AR52A225 6.3V KGM03BR50J105 6.3V KGM02AR50J153-104, KGM03AR50J474 10V KGM03AR51A223-224, KGM05AR51A105-225 16V KGM05AR51C105 Insulation Resistance : Over 10MΩ･μF X5R / R5 03 KGM03BR51A105, KGM03CR51C224, KGM03CR51E224 05 KGM05BR51A475, KGM05CR51A106, KGM05CR51V225 The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. TDS-SMDMLCC-0035 | Rev 5 – surface mount ceramic capacitor products – 23 X5R Dielectric, KGM Series Capacitance Range Case Size 01005 0201 0402 0603 0805 Soldering Reflow Only Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Packaging mm (in.) mm (in.) mm (in.) (L) Length W) Width (t) Terminal Voltage: Cap (pF) Cap (μF) 100 Paper/Embossed All Paper All Paper All Paper All Embossed 0.40 ± 0.02 (0.016 ± 0.0008) 0.20 ± 0.02 (0.008 ± 0.0008) 0.10 ± 0.04 (0.004 ± 0.0016) 0.60 ± 0.09 (0.024 ± 0.004) 0.30 ± 0.09 (0.011 ± 0.004) 0.15 ± 0.05 (0.006 ± 0.002) 1.00 ± 0.20 (0.040 ± 0.008) 0.50 ± 0.20 (0.020 ± 0.008) 0.25 ± 0.10 (0.010 ± 0.004) 1.60 ± 0.20 (0.063 ± 0.008) 0.80 ± 0.20 (0.031 ± 0.008) 0.35 ± 0.15 (0.014 ± 0.006) 2.01 ± 0.20 (0.079 ± 0.008) 1.25 ± 0.20 (0.049 ± 0.008) 0.50 ± 0.25 (0.020 ± 0.010) 6.3 101 10 16 A A 4 6.3 10 16 25 4 6.3 10 16 25 35 50 150 151 A A A 220 221 A A A A 330 331 A A A A 470 471 A A A A 680 681 A A A A 1000 102 1500 152 A 4 6.3 10 16 25 35 50 A A A A A A A A A A 2200 222 A A A A A A A 3300 332 A A A A A A A 4700 472 A A A A A A A A 6800 682 A A A A A A A A A A A A A 0.010 103 A 0.015 153 A 0.022 223 A 0.033 333 A 0.047 473 A 0.068 683 A 0.10 104 A 0.15 154 0.22 224 0.33 334 0.47 474 0.68 684 A A A A A A A A A A B 16 A A A A A A C A A A A A 105 B B C 225 C B/C C 4.7 475 C D 10 106 C A A A A A A A A A A A K A A A K A A K K K B B K K A A A A A A A A A A A K A K 01005 (KGM 02) A 0.22 PAPER H P B B B B B B B A A A A B B B B B B C C H C C C C B B B B C A A A C C C C C C C C A A A C C C A A 16 25 4 6.3 10 16 25 35 50 C C C 4 6.3 10 16 25 35 50 A A A A A A A A A 4 6.3 0603 A 0.56 F 0.6 H N H N H N B C 0.65 0.70 PAPER H H N N TDS-SMDMLCC-0035 | Rev 5 A A A A A A A A A A A A 35 50 0603 (KGM15) H 0.75 D 0.8 A 0.90 H N H N T M B C 0.95 1 PAPER T T M M The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. – surface mount ceramic capacitor products – 10 A A 0805 0402 (KGM05) D 0.55 K A B C K A B 0402 B C 0.35 0.39 PAPER H H N N B B 0201 (KGM03) H N B B B 0201 A 0.33 B B K A B 107 Case Size B B 100 Thickness Letter Max Thickness (mm) Carrier Tape Packaging Code 7"reel Packaging Code 13"reel B A 476 01005 B A 47 25 B A B 16 B A D A B A B 10 H B A C 6.3 H B A 156 4 F B A 226 16 A B A 15 10 50 A A 22 6.3 35 A A A 25 A PAPER 24 10 A A A 1 Case Size 6.3 A A A A 2.2 Voltage: 4 A 0805 (KGM21) D 1.02 K 1.40 T M U L A 1.45 EMB EMBOSSED (EMB) U L X5R Dielectric, KGM Series Capacitance Range PREFERRED SIZES ARE SHADED Case Size 1206 1210 1812 Soldering Reflow/Wave Reflow Only Reflow Only All Embossed All Embossed All Embossed 3.20 ± 0.40 (0.126 ± 0.016) 1.60 ± 0.30 (0.063 ± 0.012) 0.50 ± 0.25 (0.020 ± 0.010) 3.20 ± 0.40 (0.126 ± 0.016) 2.50 ± 0.30 (0.098 ± 0.012) 0.50 ± 0.25 (0.020 ± 0.010) 4.50 ± 0.30 (0.177 ± 0.012) 3.20 ± 0.20 (0.126 ± 0.008) 0.61 ± 0.36 (0.024 ± 0.014) Packaging mm (in.) mm (in.) mm (in.) (L) Length W) Width (t) Terminal Voltage: Cap 100 101 (pF)150 151 220 221 330 331 470 471 680 681 1000 102 1500 152 2200 222 3300 332 3900 392 4700 472 5600 562 6800 682 Cap 0.010 103 (μF) 0.012 123 0.015 153 0.018 183 0.022 223 0.027 273 0.033 333 0.039 393 0.047 473 0.068 683 0.082 823 0.10 104 0.12 124 0.15 154 0.22 224 0.33 334 0.47 474 0.68 684 4 6.3 10 16 25 35 50 M M M M M M M 1 105 H H H H H H H 2.2 225 H H H H H H H 4.7 475 H H H H H H A 10 106 H H H H A H H 22 226 H H H A H 47 476 H H H H 100 107 H H 4 6.3 Voltage: 10 16 Case Size 35 4 A 50 100 6.3 10 A 1.8 EMB U L C 1.27 EMB U L 35 50 C C E E E E E E L L L L L L L J J J J J A A A A J J J J J A A A A A L L L L L L L 4 6.3 1210 (KGM 32) H 1.9 EMB U L 25 4 6.3 10 J J J 4 6.3 10 E 1.45 EMB U L J 2.21 EMB U L 16 25 35 50 35 50 J L 10 16 25 35 50 1210 1206 (KGM 31) M 1.25 EMB U L 16 E 1206 Case Size Thickness Letter Max Thickness (mm) Carrier Tape Packaging Code 7"reel Packaging Code 13"reel 25 100 16 25 1812 1812 (KGM 43) A 2.7 EMB U L L 2.80 EMB U L J 2.80 EMB V S EMBOSSED (EMB) The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. TDS-SMDMLCC-0035 | Rev 5 – surface mount ceramic capacitor products – 25