KT1612A52000ECW18TAA

Issued Date : 16. Feb. 2012 Issued No. : R1104-12010-011 Messrs : Broadcom RoHS Compliant Temperature Compensated Crystal Oscillator ( TCXO ) KT1612A52000ECW18TAA Technical Specification KYOCERA KINSEKI Corporation (1/5) Revision History Revision No. 1 Revision Date Revision Content and reason 16. Feb. 2012 The first edition KYOCERA KINSEKI Prepared By Approved By M.Ando R.Sasagawa (2/5) TCXO KT1612A Parts Number KT1612A52000ECW18TAA A : Product Specification Code 52000 : Nominal Frequency E : Freq. Stability vs Temp +/-2.5ppm C : Bottom Temperature Limit -30deg.C W : Upper Temperature Limit +85deg.C 18 : Power Supply Voltage 1.8V T : TCXO TCXO KT1612A Electrical Characteristics Ta= -30deg.C to +85deg.C, Vcc=1.8V, Load=10pF//10kohm Symbol Item Condition Specification Unit 1.8+/-0.1 V Vcc Power Supply Voltage F0 Nominal Frequency 52.000000 MHz Topr Operating Temperature -30 to +85 deg.C Tstg Storage Temperature -40 to +85 deg.C Vout Icc Output Voltage Load:10pF/10Kohm 0.8(min) V Power Supply Current Load:10pF/10Kohm 2.0(max) mA 10(max) uA +/-2.0 ppm Ta=25+/-2deg.C +/-2.5 ppm ref:Ta=25+/-2deg.C +/-0.2 ppm +/-0.1 ppm Shutdown Current f0 Remarks Frequency Tolerance Preset Frequency and Ta=-30 to 85deg.C DC Bias shift after Twice Reflow df/F Frequency Stability vs Temp -30 to +85deg.C vs Load 10pF+/-10% 10Kohm+/-10% vs Vcc=1.8 +/-0.1V dfag Frequency Aging Rate Ta=25+/-2deg.C --- Harmonics 3rd --- SSB Carrier Noise --- Enable/Disable +/-1.0 ppm/Y -8(max) dBc @1kHz offset -125(max) dBc/Hz @10kHz offset -141(max) dBc/Hz @100kHz offset -150(max) dBc/Hz @1MHz offset -153(max) dBc/Hz Enable-Active Hi 80%Vcc(min) Disable-Active Low 20%Vcc(max) V KYOCERA KINSEKI One Year Ta=25+/-2deg.C (3/5) KT1612A Dimension, Pin Connections & Recommended Land Pattern Note : This dimension is subject to change before mass production because this product is under development. 1.70+/-0.06 0.21 #3 1.30+/-0.06 #4 Unit : ( mm ) Marking #2 0.45 0.4 0.45 0.7 Max #1 0.4 0.9 Note1 Co-planarity : 60um Max Note2 Electrode : Mo + Ni 1.5 to 8.89um + Au 0.3 to 1.0um Pin No. Pin Layout #1 Enable / Disable #2 GND #3 Output #4 Vcc 0.4 0.55 0.4 0.55 Land Pattern (Reference) 0.5 0.9 0.5 KYOCERA KINSEKI (4/5) KT1612A Recommended Circuit ※1 Bypass Capacitor and DC-Blocking Capacitor do not build in this Parts. So, Bypass Capacitor and DC-Blocking Capacitor are ※2 attached outside and please use it. And these Capacitors should be placed as close as possible to the pin (No.3 and No.4). Vcc ※2 Output ※2 ※1:0.01μF ※1:0.01μF #3 #4 TCXO top view #1 #2 Enable / Disable GND KT1612A Recommended Reflow Soldering Condition (Lead Free Version) Temp.(deg.C) 300 Soldering Zone 260 +0/-10deg.C 10sec max 250 230deg.C 200 Pre Heating Zone 180+0/-10deg.C 150 120sec max 100 50 normal temperature 0 Heating Time(sec) KYOCERA KINSEKI 40sec max (5/5) KT1612A Caution to handle 1. Touch the solder iron at 260+/-5deg.C onto the leads for 10+/-2sec max or touch the solder at 350+/-5deg.C onto the leads for 3+/-0.5sec max. 2. In the customer’s reflow process, if it will remain some mechanical stress at the soldering terminals, also make some cracks on the soldering termination. Some cracks will cause open or short circuit and cause of thermal increasing or smoking. Don’t make any excess mechanical stress to soldering points. 3. In case of giving a heavy shock to the products, it make an open or short circuit and cause of thermal increasing or smoking. To avoid heavy shock impact applying to products is strictly required. 4. Moisture Sensitivity Level MSL=1 KYOCERA KINSEKI