KT2520K37400ZAW18TBS

Drawing No. TKY1D-H1-18349-00[12] Revision History Rev.No. 00 Description of revise First Edition Date Approved by Examined by Written by Aug. 6, ‘18 N.Nakano Y.Hosoya C.Nitoube KYOCERA Corporation KBS-5079J(2/13) Drawing No. TKY1D-H1-18349-00[12] 1. Purpose and scope This document contains specification related to CRYSTAL OSCILLATOR model KT2520K37400ZAW18TBS for Digi-key. 2. Nominal condition Item MIN. TYP. MAX Unit -40 --- +85 deg.C -40 --- +85 deg.C Nominal frequency --- 37.4 --- MHz 4 Supply voltage 1.7 1.8 1.9 V 5 Absolute maximaum rating voltage (Supply voltage) Load impedance -0.6 --- +4.6 V 9 10 11 kohm 9 10 11 pF --- Clipped sine --- --- 1 Operating temperature range 2 Storage temperature range 3 6 7 Output signal condition Conditions 1.8V+/-0.1V 3. Electrical characteristics Ta=-40 to +85deg.C, Vcc=1.8V , Load=10kohm//10pF Item 1 Temp characteristics MIN. TYP. MAX Unit Conditions -6 -0.5 --- +0.5 x10 Ta= -30 to +85 deg.C -4.0 --- +4.0 x10-6 Ta= -40 to -30 deg.C 2 Voltage characteristics -0.2 --- +0.2 x10-6 1.8V+/-0.1V 3 Load characteristics -0.2 --- +0.2 x10-6 10kΩ//10pF+/-10% 4 Aging characteristics -1.0 --- +1.0 x10 /Y 5 Frequency tolerance -2.0 --- +2.0 x10-6 6 Current --- --- 2.0 mA 7 Output voltage 0.8 --- --- Vp-p 8 Harmonics --- --- -8.0 dBc 9 Phase noise --- --- -50 dBc/Hz @1Hz offset --- --- -82 dBc/Hz @10Hz offset --- --- -108 dBc/Hz @100Hz offset --- --- -130 dBc/Hz @1kHz offset --- --- -145 dBc/Hz @10kHz offset -6 Onthebasis of 25deg.Cfrequency 1year at 25+/-2 deg.C After 2 times reflow soldering at 25+/-2 deg.C KYOCERA Crystal Device Corporation KBS-5079G(3/13) Remarks at 25+/-2 deg.C Drawing No. TKY1D-H1-18349-00[12] 4. Circuit Bypass Capacitor and DC- Blocking Capacitor do not build in this TCXO. So, Bypass Capacitor and DC- Blocking Capacitor are attached outside and please use it. And these Capacitor should be placed as close as possible to the pin(No.4 and No.6). Vcc OUT N.C. 0.01uF 0.01uF #5 #6 #4 Top view #1 N.C. or GND #3 #2 N.C. GND 5. Test circuit *Load 10kohm//10pF contains the internal impedance of FET probe. A Co Power Supply Vcc 46 V 5 FET PROBE 43 11 2 3 2 RL Vcon Vcon KYOCERA Corporation KBS-5079J(4/13) Spectrum Analyzer & Counter TCXO VC-TCXO CL Drawing No. TKY1D-H1-18349-00[12] 6. Environment mechanical characteristics Item Conditions High temperature storage Ta=+85deg.C, judge on 240H storage 1 Low temperature storage Ta=-40deg.C, judge on 240H storage 2 3 High temperature and high humidity storage Ta=+85deg.C, RH=85%RH, judge on 240H storage Temperature cycle test Ta=-40 to +85deg.C 30min. each 10cycles Drop test A test piece (100g) made of Teflon is dropped 3cycles (1cycle: 6 directions) from the height of 150cm on hard board Vibration test 10 to 55 to 10Hz 1.5mm constant amplitude 1min. period X, Y, Z direction each 2H total 6H. Solder heat test All terminal electrode shall be soldered at temperature of 350+/-5deg.C for 3+/-1sec. using a soldering iron. Solderability Dip each of terminal electrode into 230+/-5deg.C solder pod for 5+/-0.5sec. after close , the test area of loads surfaces must be covered loads 90% by solder. Reflow soldering Reflow soldering at 2times. 4 5 6 7 8 9 Normal Condition: Temperature 25+/-2deg.C Humidity 30 to 70%RH Judge Item Specification At 25deg.C frequency +/-2.0ppm max(Before and After) KYOCERA Corporation KBS-5079J(5/13) Remark It must be met to the characteristics Judging criterion. Measurement shall be taken at room ambient within 2 to 24hours after each test. Drawing No. TKY1D-H1-18349-00[12] 7. Reflow profile 7-1. Preheat: 180+0/-10deg.C, 120sec (max) 7-2. Peak Temperature: 260+0/-10deg.C, 10sec (max) 7-3. PC-Board Material : FR-4 Size : 140mm*110mm Thickness : t=0.8mm 7-4. Condition of Measurement Temperature: Surface of PC-BOARD Reflow Soldering Condition Temp.(deg.C ) 300 260 +0/-10deg.C 10sec max 250 Soldering Zone 230deg.C 200 Pre Heating Zone 180+0/-10deg.C 150 120sec max 100 50 normal temperature 0 Heating Time(sec) KYOCERA Corporation KBS-5079J(6/13) 40sec max Drawing No. TKY1D-H1-18349-00[12] 8. Marking contents ####### Crystal Serial No. (Crystal Date) K XX 801X 2 3 4 5 1pin Mark *Laser Marking Contents Example 1 1Pin identifier ○ 2 Control Code1 K 3 Control Code2 XX 4 Weekly Code. 801 802 *The 2018 1st week *The 2018 2nd week 5 Control Code3 X *Specification Code (Blank or alphanumeric) KYOCERA Corporation KBS-5079J(7/13) Drawing No. TKY1D-H1-18349-00[12] 9. Dimensions 0.24 #6 #5 #4 Marking Area #1 #1pin Marking #2 #3 Top View Note1 Terminal Coplanarity:100um max Side View #1 #2 #3 Note2 Electrode : Cu + Ni + Au (10μ min+3μ min+0.03μ min) Pin Connection #6 #5 #4 Bottom View N.C. or GND # 2 pin N.C. # 3 pin # 4 pin GND Output # 5 pin # 6 pin N.C. Vcc Unit: mm KYOCERA Corporation KBS-5079J(8/13) # 1 pin Drawing No. TKY1D-H1-18349-00[12] 10.Tape & Reel I K B C G E H D #1pin Mark 5deg. max 10-1. Tape specification A F t J Feeding Direction 10-1-1. Carrier Tape material : PS Included Carbon 10-1-2. 1pin Mark is positioned on right side against the direction of feed. Symbol Dimension A 2.40+/-0.1 B 2.90+/-0.1 C 8.00+0.3/-0.2 D 3.50+/-0.05 Unit: mm E 1.75+/-0.1 Symbol Dimension F 4.00+/-0.1 G 2.00+/-0.05 H 4.00+/-0.1 I Φ1.5+0.1/-0 J Φ1.1+/-0.1 Symbol Dimension K 1.15+/-0.1 t 0.25+/-0.05 10-2.Reel specification 2+/-0.5 Ø13+/-0.2 Ø100+/-1 13.4+1/-0.5 Ø21+/-0.8 9.4+1/-0.5 (Measured at Hub) Ø330+/-2 Unit：mm 10-2-1. Reel material: PS Included Carbon 10-2-2. Reel unit: 12,000pcs max. /1Reel KYOCERA Corporation KBS-5079J(9/13) Drawing No. TKY1D-H1-18349-00[12] 10-3.Packing 10-3-1.Trailer & Leader As for the trailer and leader of taping, there are empty pockets as following drawing. Sprocket hole is positioned on upper side against the direction of feed. No missing components, excluding empty place. Trailer section : 40 pockets min Component section Leader section : 400～560mm (See enlargement underneath) Component section Empty carrier tape : 100 to 200mm Sealed with top cover tape Top cover tape only Leader section : 400 to 560mm 10-4. Shipping label Following item shall be listed on reel, bag and box. “Customer’s name”, “Parts No”, “Lot No”, “Quantity”, “Order No”, “Date of manufacture” The form of the label conforms to JEITA standard pattern C-3. KYOCERA Corporation KBS-5079J(10/13) Drawing No. TKY1D-H1-18349-00[12] 11. Top Cover breaking and peeling force 11-1. Reel Angle: 165 to 180deg 11-2. Tape Break Force: 10N min 11-3. Top Cover Tape Strength: 10N min 11-4. Top Cover Tape Peel Force: 0.1 to 1.0N 11-5. Top Cover Tape Peel Speed: 300+/-10mm / minute Top cover tape 165deg to 180deg Direction of feed Direction of feed Bottom cover tape KYOCERA Corporation KBS-5079J(11/13) Drawing No. TKY1D-H1-18349-00[12] 12. Notice 12-1. Please use soldering iron and the spot heater within the range of a solder heat test condition. 12-2. Units should be stored in a dry environment keeping away from the sun. 12-3. Don't leave units in High-temperature and High-humidity environment due to terminal solderability. (Please keep 0 to 40deg.C and 30 to 70%RH for recommendable storage condition) 12-4. The term of a guarantee of taping packing is 6 months. (0 deg.C to 40 deg.C,RH30% to 70%) 12-5. Disapprove of washing. 12-6. Unless we receive request for modification within 1 month from the issue date of this KCD specification sheet, we will supply products according to this specification. Also, if you’d like to modify specification of order, which has been placed with delivery within 1 month from the issue data of this specification sheet, we would like to discuss with you separately. 12-7. This product is intended to be used for general electronic equipment (information equipment, communication equipment, audio visual equipment, measuring equipment, home electric appliances, etc.). Devices and systems that are required for special quality and reliability, and whose failure or malfunction directly threatens human lives or that may cause harm to the human body (traffic equipment, safety equipment, aircraft and space, nuclear power control, life support equipment Please contact us in advance in case of using it for medical equipment including medical equipment etc.).. 12-8. In no event shall the company be liable for any product failure resulting from an inappropriate handling or operation of the product beyond the scope of its guarantee. 12-9. Information contained in this specification must not be quoted, reproduced or used for other purposes including processing either in part or in full without obtaining prior approval from the company. 12-10. Please keep it at the place that was the ESD protective. Human model 1.5kohm 100pF : +/-1000V Machine model 0kohm 200pF : +/-200V KYOCERA Corporation KBS-5079J(12/13) Drawing No. TKY1D-H1-18349-00[12] 13. Production place 13-1 Manufacturer KYOCERA Crystal Device Corporation. 13-2 The site of the Factory 1)5850 Higasine-Koh, Higasine-shi, Yamagata, 999-3701, Japan 2) 3-11-1 Osachi Kohagi, Okaya-shi, Nagano, 394-8550 Japan 14. Parts Numbering Guide KT2520K 37400 Z A W 18 T BS A A. B. C. D. E. F. G. H. B C D E F G H Series (2.5x2.0 SMD KT2520K) Frequency (37.4MHz) Frequency temperature accuracy ( Z: Special specification ) Minimum temperature range ( A: -40deg.C) Maximum temperature range ( W: +85deg.C ) Supply voltage (18: 1.8V) Control voltage stability (T: TCXO) Customer special model Suffix KYOCERA Corporation KBS-5079J(13/13)