ST121C126MAJ05

TurboCapTM High-CV SMPS Capacitors The TurboCapTM, MLC capacitors from AVX Corporation are characterized with very high capacitance in a small volume. By vertical stacking of the ceramic elements, the footprint required for mounting the capacitors is greatly reduced. TurboCapsTM are ideally suited as filters in the input and output stages of switch mode power supplies (SMPS). With their ultra-low ESR, these capacitors are designed to handle high ripple current at high frequencies and high power levels. The DIP leads in either thru-hole or surface mount configurations offer superior stress relief to the ceramic elements. The leads effectively decouple the parts from the board and minimize thermally or mechanically induced stresses encountered during assembly, temperature cycling or other environmental conditions. TYPICAL APPLICATION OF TURBOCAPTM SMPS CAPACITORS FOR INPUT AND OUTPUT FILTERS IN DC/DC CONVERTERS SNUBBER Vout Vin OUTPUT FILTER INPUT FILTER VCC FB G PWM CONTROLLER GND Performance of SMPS capacitors can be simulated by downloading SpiCalci software program http://www.avx.com/SpiApps/default.asp#spicalci Custom values, ratings and configurations are also available. MAY 2015 ■ 49 TurboCapTM High-CV SMPS Capacitors ELECTRICAL SPECIFICATIONS Temperature Coefficient Temperature Coefficient Dielectric Withstanding Voltage 25°C (Flash Test) 250% rated voltage for 5 seconds with 50 mA max charging current. ±15%, -55° to +125°C Capacitance Test (MIL-STD-202 Method 305) 25°C, 1.0±0.2 Vrms (open circuit voltage) at 1KHz Life Test (1000 hrs) X7R: 150% rated voltage at +125°C. Dissipation Factor 25°C 2.5% Max @ 25°C, 1.0±0.2 Vrms (open circuit voltage) at 1KHz Moisture Resistance (MIL-STD-202 Method 106) Ten cycles with no voltage applied. Insulation Resistance 25°C (MIL-STD-202 Method 302) 500 MΩ-μF, whichever is less. Thermal Shock (MIL-STD-202 Method 107, Condition A) Insulation Resistance 125°C (MIL-STD-202 Method 302) 50 MΩ-μF, whichever is less. Resistance To Solder Heat (MIL-STD-202, Method 210, Condition B, for 20 seconds) Immersion Cycling (MIL-STD-202 Method 104, Condition B) Typical ESR Performance (Ω) 27μF 0.007 0.003 0.002 ESR @ 10KHz ESR @ 50KHz ESR @ 100KHz 47μF 0.004 0.002 0.0015 100μF 0.003 0.0015 0.001 Not RoHS Compliant HOW TO ORDER AVX Styles: ST12 and ST20 ST12 5 C 186 M A N 03 AVX Style ST12 ST20 Voltage 25V = 3 50V = 5 100V = 1 Temperature Coefficient X7R = C Capacitance Code (2 significant digits + no. of zeros) 1 μF = 105 10 μF = 106 100 μF = 107 Capacitance Tolerance M = ±20% Test Level A = Standard Termination N = Straight Lead J = Leads formed in L = Leads formed out Number of Leads Per Side 03 = 3 05 = 5 10 = 10 CAPACITANCE (μF) ST12 Cap (μF) .82 1.3 2.7 8.2 12 14 18 22 27 47 50 68 100 220 50 ■ MAY 2015 50V ST20 100V Voltage 25V 50V 100V ...03 ...05 ...03 ...03 ...10 ...05 ...05 ...03 ...05 ...10 ...03 ...05 ...10 ...10 ...10 TurboCapTM High-CV SMPS Capacitors E D B A 1.397 (0.055) ±0.254 (0.010) 6.35 (0.25) MIN. 0.254 (0.010) TYP. 0.508 (0.020) TYP. C 3, 5 or 10 leads per side 2.54 (0.100) TYP. 2.54 (0.100) MAX. 0.635 (0.025) MIN. “N” STYLE LEADS E D B 0.254 (0.010) RAD. TYP. A 1.397 (0.055) ±0.254 (0.010) 1.778 (0.070) ± 0.254 (0.010) B 0.508 (0.020) TYP. 3, 5 or 10 leads per side 1.397 (0.055) ± 0.127 (0.005) C 2.54 (0.100) TYP. 2.54 (0.100) MAX. 0.635 (0.025) MIN. “J” STYLE LEADS E D B A 1.397 (0.055) ±0.254 (0.010) 1.778 (0.070) ± 0.254 (0.010) B 0.508 (0.020) TYP. 3, 5 or 10 leads per side 0.254 (0.010) RAD. TYP. 1.397 (0.055) ± 0.127 (0.005) C 2.54 (0.100) TYP. 2.54 (0.100) MAX. 0.635 (0.025) MIN. “L” STYLE LEADS DIMENSIONS Style ST125C***M*N03 ST125C***M*N05 ST125C***M*N10 ST205C***M*N03 ST205C***M*N05 ST205C***M*N10 millimeters (inches) A (max.) 3.56 3.56 3.56 5.59 5.59 5.59 (0.140) (0.140) (0.140) (0.220) (0.220) (0.220) B (max.)* 5.21 5.21 5.21 7.24 7.24 7.24 (0.205) (0.205) (0.205) (0.285) (0.285) (0.285) C ± 0.635 (± 0.025) 5.08 (0.200) 5.08 (0.200) 5.08 (0.200) 6.35 (0.250) 6.35 (0.250) 6.35 (0.250) D (max.) 10.8 (0.425) 15.9 (0.625) 27.9 (1.100) 9.5(0.375) 14.6 (0.575) 27.3 (1.075) E (max.) 6.35 6.35 6.35 7.62 7.62 7.62 (0.250) (0.250) (0.250) (0.300) (0.300) (0.300) Lead Style N N N N N N No. of Leads Per Side 03 05 10 03 05 10 *The “B” dimension is defined for the “N” Style leads. The “L” and “J” Style Leads are 0.381 (0.015) longer. The ST12 will be 5.89 (0.220), the ST20 will be 7.62 (0.300). MAY 2015 ■ 51