TAWD106K025R0600

TAW Series Tantalum Solid Electrolytic Fused Capacitors • Thin film fuse connected in series with capacitor • Protection from possible damaging from high DC leakage current (short circuit failure) • CV range: 6.8-100μF / 10-50V • Application: servers LEAD-FREE COMPATIBLE COMPONENT CASE DIMENSIONS: millimeters (inches) Code D EIA Code EIA Metric L±0.20 (0.008) W+0.20 (0.008) H+0.20 (0.008) -0.10 (0.004) –0.10 (0.004) 2917 7343-31 7.30 (0.287) 4.30 (0.169) 2.90 (0.114) W1±0.20 (0.008) A+0.30 (0.012) -0.20 (0.008) S Min. 2.40 (0.094) 1.30 (0.051) 4.40 (0.173) W1 dimension applies to the termination width for A dimensional area only. For part marking see page 169 HOW TO ORDER D TAW Type Case Size See table above 476 * 010 Capacitance Code pF code: 1st two digits represent significant figures 3rd digit represents multiplier (number of zeros to follow) Tolerance K=±10% M=±20% Rated DC Voltage 010=10Vdc 016=16Vdc 020=20Vdc 025=25Vdc 035=35Vdc 050=50Vdc R Packaging R = Pure Tin 7" Reel S = Pure Tin 13" Reel 0500 ESR in mΩ TECHNICAL SPECIFICATIONS Technical Data: Capacitance Range: Capacitance Tolerance: Rated Voltage (VR)  +85°C: Category Voltage (VC)  +125°C: Surge Voltage (Vs)  +85°C: Surge Voltage (Vs)  +125°C: Fuse Off Fuse Continuous Current Capability Temperature Range: Reliability: 114 ■ JANUARY 2014 All technical data relate to an ambient temperature of +25°C 6.8 μF to 100 μF ±10%; ±20% 10 16 20 25 35 50 7 10 13 17 23 33 13 20 26 32 46 65 8 13 16 20 28 40 I > 4A in 1s, insulating resistance > 10MΩ 0.75A -55°C to +125°C 1% per 1000 hours at 85°C, Vr with 0.1Ω/V series impedance, 60% confidence level TAW Series Tantalum Solid Electrolytic Fused Capacitors CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance μF Code 1.0 105 2.2 225 4.7 475 6.8 685 10 106 22 226 33 336 47 476 100 107 6.3V (J) 10V (A) Rated Voltage DC (VR ) to 85°C 16V (C) 20V (D) D(600) D(600) D(500) D(500) D(600) D(800) D(500) D(500) 25V (E) 35V (V) 50V (T) D(600) D(600) D(700) D(700) Available Ratings (ESR ratings in mOhms in brackets) Engineering samples - please contact manufacturer *Codes under development – subject to change Note: Voltage ratings are minimum values. AVX reserves the right to supply higher ratings in the same case size, to the same reliability standards. RATINGS & PART NUMBER REFERENCE AVX Part No. Rated Case Capacitance Voltage Size (μF) (V) DCL DF ESR (μA) % Max. (mΩ) MSL Max. Max. @100kHz 100kHz RMS Current (mA) 25ºC 100kHz RMS Voltage (mV) 85ºC 125ºC 25ºC 85ºC 125ºC 493 493 219 219 274 274 246 246 110 110 450 390 200 173 300 346 270 312 120 139 493 493 219 219 274 274 246 246 110 110 450 450 200 200 300 300 270 270 120 120 450 450 200 200 300 300 270 270 120 120 417 417 185 185 324 324 292 292 130 130 10 Volt @ 85ºC (7 Volt @ 125ºC) TAWD476*010#0500 TAWD107*010#0500 D D 47 100 10 10 4.7 10 6 8 500 500 1 1 548 548 TAWD336*016#0600 TAWD476*016#0800 D D 33 47 16 16 TAWD226*020#0500 TAWD336*020#0500 D D 22 33 20 20 TAWD106*025#0600 TAWD226*025#0600 D D 10 22 25 25 TAWD685*035#0600 TAWD106*035#0600 D D 6.8 10 35 35 TAWD685*050#0700 TAWD106*050#0700 D D 6.8 10 50 50 5.3 6 600 1 500 7.5 7 800 1 433 20 Volt @ 85ºC (13 Volt @ 125ºC) 4.4 6 500 1 548 6.6 6 500 1 548 25 Volt @ 85ºC (17 Volt @ 125ºC) 2.5 6 600 1 500 5.5 6 600 1 500 35 Volt @ 85ºC (23 Volt @ 125ºC) 2.4 6 600 1 500 3.5 6 600 1 500 50 Volt @ 85ºC (33 Volt @ 125ºC) 3.4 6 700 1 463 5 6 700 1 463 16 Volt @ 85°C (10 Volt @ 125°C) Moisture Sensitivity Level (MSL) is defined according to J-STD-020. All technical data relates to an ambient temperature of +25°C. Capacitance and DF are measured at 120Hz, 0.5V RMS with a maximum DC bias of 2.2 volts. DCL is measured at rated voltage after 5 minutes. TYPICAL FUSE ACTUATION Typical Actuation Time vs Load Current For typical weight and composition see page 162. 100.000 Actuation Time [ms] NOTE: AVX reserves the right to supply a higher voltage rating or tighter tolerance part in the same case size, to the same reliability standards. 10.000 1.000 0.100 0.010 0.001 1 10 Current [A] 100 Note: for a different fuse characteristic requirements please contact manufacturer JANUARY 2014 ■ 115