AXIS50-11

Issue: 06 Date: 2006-03-16 Specification AXIS50-11 Oscillator type : UHF VCXO with LVPECL or Sinus Output Parameter Frequency range Standard frequencies Frequency stability Initial tolerance vs. temperature in operating temperature range (-20°~+50°C) vs. supply voltage variation vs. load change long term (aging) Long term aging over 10 years Frequency adjustment range Electronic Frequency Control (EFC) range @ 25°C EFC voltage VC EFC slope (∆f / ∆VC) EFC linearity EFC input impedance RF output Signal waveform min. typ. max. Unit Condition 60 350 MHz 60 / 93.333 / 186.667 / 213.3 MHz / 311.040 ppm ppm ± 10 ppm -0.1 -0.1 0.1 0.1 ±2 ± 10 -20°C ~ +50°C ppm ppm ppm/year @ 40°C ppm ppm ppm V % kΩ Option S Option L RL = 50 Ω ± 15 0.15 positive 100 SINUS LVPECL Complementary -3 40 3.15 Amplitude (Option S) dBm Anharmonics attenuation (Option S) dB Output Levels (Option L) -20°C ~ +50°C HIGH (VOH) 2,215 2,345 2,420 V RL = 50 Ω to VS - 2 V LOW (VOL) 1,470 1,595 1,745 V Note 2 3.15 3.3 3.45 V Supply voltage VS Current consumption (steady state) 40 mA -30 +60 °C Operable temperature range -40 +85 °C Storage temperature range 20.5x20.5x10.5 max. mm IEC 60679-3 or 61837 Enclosure (see drawing) 5 gram Weight bulk IEC 60286-3 Packing 1500 V HBM, IEC 61000-4-2 ESD Sensitivity Notes: 1. Terminology and test conditions are according to IEC standard IEC60679-1, unless otherwise stated 2. Output parameters vary 1:1 with VS Ordering Code: Model (Specification) AXIS50-11 Option Frequency [MHz] S 311.040 GmbH & Co. KG Wasemweg 8 D-74821 Mosbach Germany AXIS50-11 page 1(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: info@axtal.com Enclosure drawing Pin connections: Pin # Symbol 1 N.C. Q 2 RF OUT 3 GND 4 VC 5 VS Function No Connection (Option S) RF Output ( Q ) (Option L) RF Output (Q) Ground Control Voltage (EFC) Supply Voltage Environmental conditions Test Visual inspection, dimensions Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* Bump* Free fall* IEC 60068 Part ... IEC 60679-1 clause ... 4.3 4.6.2 4.6.3 Test conditions Enclosure styles as in IEC 60679-3 or 61837, if applicable Gross leak: Test Qc, Fine leak: Test Qk Test Ta (235 ± 5)°C Method 1 Test Tb Method 1A, 5s Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Eb, 4000 bumps per Axes, 40g, 6 ms Test Ed procedure 1, 2 drops from 1m height Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Na, 10 cycles at extremes of operating temperature range Test Ba, 16 h at upper temperature indicated by climatic category Test Db variant 1 severity b), 55°C/95% r.H., 6 cycles Test Aa, 2 h at lower temperature indicated by climatic category Sequence of 4.6.14, 4.6.15 (1st cycle), 4.6.16, 4.6.15 (5 cycles) Test Ca, 56 days 2-17 2-20 2-58 2-27 2-29 2-32 4.6.8 4.6.6 4.6.9 4.6.7 Vibration, sinusoidal* 2-6 Rapid change of temperature Dry heat Damp heat, cyclic* Cold Climatic sequence* Damp heat, steady state* Endurance tests - ageing - extended aging 2-14 2-2 2-30 2-1 1-7 2-3 4.6.5 4.6.14 4.6.15 4.6.16 4.6.17 4.6.18 4.7.1 4.7.2 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C GmbH & Co. KG Wasemweg 8 D-74821 Mosbach Germany AXIS50-11 page 2(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: info@axtal.com