AXMW8596

Issue: 01 Date: 2005-02-01 Specification AXMW8596 Oscillator type : Crystal Controlled Microwave Oscillator Parameter Frequency range Standard frequencies Frequency stability Initial tolerance vs. temperature in operating frequency range (steady state) medium term (aging) over 24 hours Frequency selection Electronic Frequency Control RF output Signal waveform Load Load VSWR Output Power Output Power Variation min. typ. max. Unit GHz ppm ppm ppm ppm Condition 8.5 9.6 6 frequencies within 4% -50 -100 -1 50 100 1 @25°C -40°~+70°C @ constant temp. Note 2 By grounding of appropriate selection pin SINUS 50 1.5 50 2 3 2 50 90 65 -90 -75 -68 10 28.5 600 500 80 100 +85 TBD bulk 1500 V mW dB dB dB dB dBc dBc dBc Hz / g V mA mV % % °C mm gram Ohm Spurious Outputs (Note 1) AM Noise (Note 1) FM Noise (Note 1) Vibration Sensitivity Supply voltage VS Current consumption (steady state) Power line Ripple Noise (pk-pk) Relative Humidity Storage temperature range Enclosure L x W x H (see drawing) Weight Packing ESD Sensitivity 0°C ~ +70°C -30°C ~ +70°C between 6 frequencies Fc ± 5 MHz Outside fc ± 5 MHz fc ± 30 MHz ~60 MHz elsewhere fc ± 30 MHz ~60 MHz See graph 1 27.5 28.0 -55 100 x 70 x 30 50 Hz ~ 200 MHz Continuous During warm-up 95% R.H. HBM as in IEC 610004-2 Notes: 1. Terminology and test conditions are according to IEC standard IEC60679-1, unless otherwise stated 2. Channel selection by connecting ground (pin 7) to one of the 6 pins in Viking connector VR7/4AB13 The six nominated frequencies to be determined by the purchasing-order GmbH & Co. KG Wasemweg 5 D-74821 Mosbach Germany AXMW 8596 page 1(5) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: info@axtal.com Enclosure drawing: Pin connections: VR7/4AB13 connector: Pin # Symbol Function 1 CH1 Channel 1 select 2 CH2 Channel 2 select 3 CH3 Channel 3 select 4 CH4 Channel 4 select 5 CH5 Channel 5 select 6 CH6 Channel 6 select 7 Ground SMA Connector: RF Output BNC Connector : VS Supply Voltage Mounting plate: Marking: AXMW8596 AXTAL ww/xx & serial number Environmental conditions: Vibration : Specification must be met under the vibration conditions of the chart below (Graph 1). Shock : Half Sine 15 g, 11 ms in 3 mutually perpendicular axes. No damage. Shock not applied to short term stability requirements GmbH & Co. KG Wasemweg 5 D-74821 Mosbach Germany AXMW 8596 page 2(5) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: info@axtal.com Typical spectrum drawing 1: Typical spectrum drawing 2: * RBW 10 kHz * VBW 50 Hz Ref 20 20 dBm Att 45 dB SWT 8 s 10 1 AP CLRWR A 0 -10 -20 -30 -40 -50 -60 -70 -80 Center 9.07 GHz 200 kHz/ Span 2 MHz AXTAL GmbH & Co. KG Wasemweg 5 D-74821 Mosbach AXMW8596 page 3(5) www.axtal.com info@axtal.com fon: +49 6261 939834 fax: +49 6261 939836 Ref 20 10 1 SA CLRWR 20 dBm PHN 17.616 dBm Att 45 dB 1 RBW 20 kHz VBW 2 kHz SWT 50 ms Delta 2 [T1 PHN] -91.37 dBc/Hz 99.358974360 kHz Marker 1 [T1 FXD] 17.66 dBm 9.015004397 GHz A 0 -10 -20 -30 2 -40 -50 -60 -70 PHN -80 Center 9.015006 GHz 100 kHz/ Span 1 MHz RBW 3 MHz Ref 20 20 dBm Att 45 dB VBW 300 kHz SWT 155 ms Marker 1 [T1 ] -39.28 dBm 500.000000000 MHz 10 1 AP CLRWR A 0 -10 -20 -30 1 -40 -50 -60 -70 -80 Center 13.25 GHz 2.65 GHz/ Span 26.5 GHz AXTAL GmbH & Co. KG Wasemweg 5 D-74821 Mosbach AXMW8596 page 4(5) www.axtal.com info@axtal.com fon: +49 6261 939834 fax: +49 6261 939836 Typical PLL settling time during switch from channel 1 to channel 6: Typical PLL settling time during switch from channel 6 to channel 1: Typical PLL settling time during switch from channel 2 to channel 3: AXTAL GmbH & Co. KG Wasemweg 5 D-74821 Mosbach AXMW8596 page 5(5) www.axtal.com info@axtal.com fon: +49 6261 939834 fax: +49 6261 939836