AZOLED034A

AZ DISPLAYS, INC. COMPLETE LCD SOLUTIONS SPECIFICATIONS FOR OLED DISPLAY PART NUMBER: DATE: AZOLED034A & AZOLED034A-T August 27, 2009 AZOLED034A 1. General Description 1.1 Features AZOLED034A ACTIVE OLED PANEL Ultra Compact NTSC/P AL/SECAM Video Auto Switch Single Operation Voltage +12V CVBS / S-Video (Option) / Analog RGB (PC Mode) Signal Input Support Touch Screen Function (option) 1.2 Applications Portable product Industrial Hand-held Security Instrument Display Office Electronics 1.3 Application Precautions Do not use the products herein for the following equipment which demands extremely high performance in terms of functionality, reliability, or accuracy. Aerospace equipment Communication equipment for trunk lines. Control equipment for the nuclear power industry. Medical equipment related to life support, etc. The other application that demands high reliability and functionality should first contact a sales representative. AZ DISPLAYS, INC. PAGE 02 OF 23 2. Block Diagram 2.1 Block Diagram AZ DISPLAYS, INC. PAGE 3 OF 23 3.1 Panel Mechanical Specifications Parameter Specifications Unit inch dot mm mm 3.Panel Information Screen Size Display Format Active Area Pixel Pitch Pixel Configuration Outline Area Thickness 3.4 (diagonal) 480 x (R.G.B) x 272 74.88(W) x 42.43 (H) 0.156(W) x 0.156(H) Stripe 82.8(W) x 54.3(H) 1.6 mm mm 3.2 Panel Optical Characteristics Parameter Symbol Condition Min Typ Max Unit deg Re Horizontal Viewing Angle Vertical Left Right Top Bottom At optimized CR Tr Tf U x y θ= 0° θ= 0° 25C --Viewing angle θ= 0° 5000:1 CR >10 170 170 170 170 --------- deg deg Contrast Ratio 10000:1 ------50 75 200 0.28 0.30 ----230 0.33 0.35 --- --- Response time Uniformity Brightness White Chromaticity LED Life Time Rise Fall --us --- --70 170 0.23 0.25 30000 --- Hr AZ DISPLAYS, INC. PAGE 04 OF 23 4.1 Panel Mechanical Specifications (With Touch) Parameter Specifications Unit inch dot mm mm Screen Size Display Format Active Area Pixel Pitch Pixel Configuration Outline Area Thickness 3.4 (diagonal) 480 x (R.G.B) x 272 74.88(W) x 42.43 (H) 0.156(W) x 0.156(H) Stripe 82.8(W) x 54.3(H) 2.8 mm mm 4.2 Panel Optical Characteristics (With Touch) Parameter Symbol Condition Min Typ Max Unit deg Remark Horizontal Viewing Angle Vertical Left Right Top Bottom At optimized CR Tr Tf x y Viewing angle θ= 0° CR >10 --------5000:1 ----136 θ= 0° θ= 0° 25 ℃ 0.26 0.28 30000 --- 170 170 170 170 --------- deg deg Contrast Ratio 10000:1 ----160 0.31 0.33 ----50 184 0.36 0.38 --- --- Response time Brightness White Chromaticity Operation life time Rise Fall --us cd/m² Hr AZ DISPLAYS, INC. PAGE 5 OF 23 5. Dimension Information 5.1 Unit(AZOLED034A) AZ DISPLAYS, INC. PAGE 06 OF 23 5.2 Unit (AZOLED034A-T) AZ DISPLAYS, INC. PAGE 7 OF 23 AZ DISPLAYS, INC. AZ DISPLAYS, INC. PAGE 8 OF 23 AZ DISPLAYS, INC. 6. Pin Description 6.1 J301 OLED LCD Panel I/O Terminals(FPC 71 Pin Below Contact Type) Pin No Symbol I/O Description Remark 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 TP1 TP2 TP3 TP4 AR_VSS AR_VSS TEST1_VS AR_VDD AR_VDD I I I I I I I I Touch panel P1 Touch panel P2 Touch panel P3. Touch panel P4 Negative voltage for OLED Negative voltage for OLED Positive voltage for OLED Positive voltage for OLED Panel refers voltage of the regulator ARREF or external input voltage.(-8V~+8V) Low Voltage output of regulator VGL or external input voltage.(-3V~-8V) High Voltage output of regulator VGH or external input voltage.(+3V~+8V) Negative output voltage of the booster2. (-8.5V) Connect to the step-up circuit, capacitors according to the step-up factor. Leave this pin open if the internal step-up circuit is not used. Positive output voltage of the booster2. (8.5V) Connect to the step-up circuit, capacitors according to the step-up factor. Leave this pin open if the internal step-up circuit is not used. Connect to the step-up circuit, capacitors according to the step-up factor. Leave this pin open if the internal step-up circuit is not used. Charge pump ground pin, it must connect to external ground. Output voltage of the booster1. (5.1V/6.0V) Analog ground pin. It must connect to external ground. Analog ground pin. It must connect to external ground. A power supply for the Analog circuit. (3.0V~3.6V) A power supply for the Analog circuit. (3.0V~3.6V) Output voltage of the VGAM1OUT regulator and used positive powerof source driver. (4.8V/5.8V) Internal logic voltage input or output pin VDC_ENB=0, VDDD is output, please connect to 1uF capacitor. VDC0 0 1 VDDD 1.8 2.5 Status Norml display OTP program open CMEL test pin, it must be open. TEST2_VD open CMEL test pin, it must be open. ARREF VGL VGH LVO C22N C22P HVO C21P C21N C11N C11P C12N C12P PVSS DDVDH VSSA VSSA VCI VCI P P I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O P I/O P P VGAM1OUT I/O 31 I/O AZ DISPLAYS, INC. PAGE 09 OF 23 VDC_ENB=1, VDDD is input. (Input range = 1.6V~2.75V) 32 33 34 35 36 37 38 VCC VSSD NRESET NCS SCL SDA DE P P I I I I I A power supply for the Digital circuit. (1.5V~3.6V) Digital ground pin. It must connect to external ground. Reset pin. Setting either pin low initializes the LSI. Must be reset after power is supplied. (Normally pull high) Serial Interface chip enable pin. (Normally pull high) Serial Interface clock input pin. (Normally pull high) Serial Interface data line. (Normally pull high) Data enable: When VSYNC+HSYNC+DE mode, DE=H: Data enable, DE=L: Data disable (Black). (Normally pull low) Frame synchronizing signal. 39 VSYNC I If VSPL=0: Active low. If VSPL=1: Active high. Line synchronizing signal. 40 HSYNC I If HSPL=0: Active low. If HSPL=1: Active high. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 DCLK D27 D26 D25 D24 D23 D22 D21 D20 D17 D16 D15 D14 D13 D12 D11 D10 D07 D06 D05 D04 D03 D02 2. I I Dot clock signal. If DPL=0: Data are input on the rising edge of DOTCLK. If DPL=1: Data are input on the falling edge of DOTCLK. Digital data input. DX0 is LSB and DX7 is MSB. (Normally pull low) 1. If parallel RGB input mode is used, D0X, D1X, and D2X indicate R, G, and B data in turn. If serial RGB or RGBD or CCIR601 or CCIR656 input mode is selected, only D07~D00 are used, and others short to GND. DX7~DX0 has 8-bit width, respectively to compose 16,777,216 color and 256 gray scale of 1 pixel. AZ DISPLAYS, INC. PAGE 10 OF 23 64 65 66 67 68 69 70 71 D01 D00 TEST3_W AR_VDD AR_VDD AR_VSS AR_VSS TEST4_P open CMEL test pin, it must be open. I I I I Positive voltage for OLED Positive voltage for OLED Negative voltage for OLED Negative voltage for OLED open CMEL test pin, it must be open. 6.2 J101 Pin Assignment of Analog RGB Input (D-Sub 15 Pin) Pin No Symbol I/O Description Remark 1 2 3 4 5 6 7 8 9 10 11 12 13 14 NC NC NC GND NC VS_IN HS_IN AGND RI+ AGND GI+ AGND BI+ GND I - I I I I - No Connection No Connection No Connection Ground No Connection TTL Vertical sync TTL Horizontal sync Analog Ground Analog Red Signal Analog Ground Analog Green Signal Analog Ground Analog Blue Signal Ground AZ DISPLAYS, INC. PAGE 11 OF 23 6.3 J105 Pin Assignment of Key (Pitch 1.25mm 9Pin, Side Entry Type) Pin No Symbol I/O Description Remark 1 2 3 4 5 6 7 8 9 N.C KEY-ADC1 KEY-ADC0 GND VDD IR_DATA LED-R LED-G GND I I I O O - No Connection KEY ADC Input 1 KEY ADC Input 0 Ground +3.3V Output Voltage DATA of IR Receiver Index Red LED for power off control Index Green LED for power on control Ground 6.4 J102C Pin Assignment of Signal Input (Pitch 1.25mm 15Pin, Side Entry Type) Pin No Symbol I/O Description Remark 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 VCC12V VCC12V GND_D GND_D VIDEO1 GND_A VIDEO2 GND_A N.C AGND S1_Y+ GND S1_C+ GND GND_D - I I - +12V Input Voltage +12V Input Voltage Ground Ground Video1 Input Signal Ground For Video1 Video2 Input Signal Ground For Video2 No Connection I I - Analog Ground Analog Luma Input of S-Video1 Ground for Analog Luma Input of S-Video1 Analog Chroma Input of S-Video1 Ground for Analog Chroma Input of S-Video1 Ground AZ DISPLAYS, INC. PAGE 12 OF 23 7. Absolute Maximum Ratings 7.1 Absolute Maximum Ratings Parameter Symbol Min Max Unit V Vp-p Vp-p Vp-p V C @75 @75 @75 Remark Input Voltage Video Input Signal S-Video Input Signal Analog RGB Input Signal Digital Input Signal Operating Temperature Storage Temperature Vin Video in S-Video in Analog RGB in TTL -10 0.5 0.5 0.5 +10 +14 2.0 2.0 2.0 +0.3 -20 +3.6 +60 +70 C AZ DISPLAYS, INC. PAGE 13 OF 23 8. Recommended operating conditions 8.1 Electrical Characteristics Parameter Symbol I/O Min Typ Max Unit V mA W @+12V I=10mA @75 @75 @75 @75 Note Input Voltage Total Current Power Consumption Output Voltage Video Input Signal S-Video Input Signal Analog RGB Input Signal Vin Iin VDD Video in S-Video in Analog RGB in Y C RGB I I I O I I I I +11 +12 195 2.3 +13 +3.2 +3.3 1.0 0.7 0.286 0.7 +3.4 V Vp-p Vp-p Vp-p Vp-p 8.2 VGA Mode Characteristics Dots per inch Hor. Unit KHz KHz Polarity Ver. Unit Hz Hz Polarity Note 640*480 800*600 31.469 37.879 Negative Positive 59.941 60.317 Negative Positive 8.3 Optics Sample Test Data Parameter White Window Red Green Blue Remark S/N 001 x .y L(cd/m²) TC(°K) 0.281 0.305 349 9150 BM-7 FAST(TOPCON) 0.651 0.346 0.282 0.678 0.148 0.145 ±15 2.Video Pattern Generator: FLUKE PM54200 3. Measurement Distance 500mm 50mm 4. TOPCON BM-7 Luminance Meter 2° filed of view is used in the testing (After 10min ~20min operation) AZ DISPLAYS, INC. PAGE 14 OF 23 9.Operation manual 9.1 Driver Board Manual To AZOLED034A KEYBOARD TO I/O BOARD To USB Board 9.2 Power and RCA Input Board (Optional) AZ DISPLAYS, INC. PAGE 15 of 23 10. Key Function by OSD 10.1 Menu Operation Current selected indicator Meaning of the selected indicator Other indicators Current value Fig. 9-1 Expand current selected indicator Adjustable range To Driver Board (J105) POWER AUTO SOURCE MENU UP DOWN Operations of key board 1. To navigate the menu, press [MENU]. (Fig. 9-1) 2. The indicator lighting up in white color is the selected adjustment item. 3. To Next Item of the menu, press [MENU] again. 4. The operations below are only available when • MenuŽ is st arted. 5. Press [UP] / [DOWN] to adjust the value of the selected item. AZ DISPLAYS, INC. PAGE 16 OF 23 Overview of the menu Indicator Meaning Brightness Contrast Color Tint Sharpness Color Tone H-Position V-Position Auto Scan Information Setup Factory Set Exit Over Scan / Under Scan Adjustable range 0 0 0 0 0 64 64 64 32 16 For AV / S-Video / VGA AV / S-Video / VGA AV / S-Video AV / S-Video AV / S-Video AV / S-Video / VGA AV / S-Video / VGA AV / S-Video / VGA VGA AV / S-Video AV / S-Video / VGA AV / S-V AV / S-Video / VGA AV / S-Video / VGA Fig. 9-2 Fig. 9-3 Balance-Bar Balance-Bar Adjust-Bar Remark Adjust-Bar Adjust-Bar Adjust-Bar Normal / Warm / Cool -25 -10 +25 +10 Fig. 9-2 AZ DISPLAYS, INC. PAGE 17 OF 23 Setup Menu Firmware VER 0.25 above Fig. 9-3 Indicator Meaning Show Status Blue Screen Auto Power On Auto Sleep Detect Source Return Adjustable range ON / OFF ON / OFF ON / OFF OFF / 3s / 5s / 15s / 30s ON / OFF Function Show screen status. If loss signal will put on the blue or black screen. auto turn on. If signal loss over setting times will be power off. in exist. Remark ON: Show OFF: Hidden ON: Blue OFF: Black OFF: Manual ON: Auto OFF: Normal OFF: Normal Power input module will be ON: Auto Auto detection which source ON: Auto Note : Priority : Auto Sleep > Auto Power On Note : VGA Only don't have D etect Source function. AZ DISPLAYS, INC. PAGE 18 OF 23 10.2 Operation Indicator of input signal Video system Fig. 9-4 [Power] [Source] Monitor power on / off Input signal switch Overview of input signals Indicator Input signal VGA Interface Analog RGB Video system 640x480_60 / 800x600_60 AZ DISPLAYS, INC. PAGE 19 OF 23 11. Application Schematic Diagram 11.1 Application Circuit AZ DISPLAYS, INC. PAGE 20 OF 23 11.2 Key and IR Circuit AZ DISPLAYS, INC. PAGE 21 OF 23 11.3 Keyboard AZ DISPLAYS, INC. PAGE 22 OF 23 11.4 S-Video and RCA Input Board AZ DISPLAYS, INC. PAGE 23 OF 23