ED050SC3

E D 050S C 3 V er s i on: 2 .0 T E C HNICA L M ODE L Pl ease contact PV I or i ts agent f or further i nformati on S PE CIFICA T I ON N O. : E D050SC3 T he content of this information is subject to be changed without notice. C ustomer•s Confirmation C ustomer D ate By PV I • s Confirmation FOR MORE INFORMATIO N: AZ DISPLAY S, INC. 75 COLUMBIA, ALISO VIEJO, CA, 92656 Http://www.AZDISPLAY S.com C onfirmed B y Prepared B y T he information contained herein is the exclus ive property of P rime V iew I nternational C o., Ltd. and s hall not be dis tributed, reproduced, or dis clos ed in whole or in part without prior written permis s ion of P rime V iew I nternational C o., Ltd. P AG E :1 ED050SC3 Revision History Rev. 1.0 Issued Date August.15.2008 Revised New Add Page 7 6-2) Absolute maximum rating Page 16 11.Bar Code definition Page 17 12.Border definition Modify Page 4 3. Mechanical Specifications Page 7 6-3) Panel DC characteristics Page 9 7.Power on sequence 2.0 October.7.2008 Page 14 9. Handling, Safety and Environment Requirements Del Preliminary specification Page 15 10.Reliability test 14.Stylus Tapping Top R:0.4mm Load: 300gf Speed: 5 times/sec Total 13,500times change to Top R:0.8mm Load: 300gf Speed: 2 times/sec Total 13,500times Del Page 13 Note 8-1 Contents The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:2 ED050SC3 TECHNICAL SPECIFICATION CONTENTS NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 ITEM Cover Revision History Contents Application Features Mechanical Specifications Mechanical Drawing of EPD module Input/Output Terminals Electrical Characteristics Power on Sequence Optical Characteristics Handling, Safety and Environment Requirements Reliability test Bar Code Definition Border Definition Block Diagram Packing PAGE 1 2 3 4 4 4 5 6 7 10 12 14 15 16 17 17 18 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:3 ED050SC3 1. Application The display is a TFT active matrix electrophoretic display, with associated interface and control logic, and a reference system design. The 5” active area contains 800x600 pixels, and has full 1~4 bit display capabilities An integrated circuit containing interface, timing and control logic is supplied with each panel. 2. Features High contrast TFT electrophoretic 800x600 display High reflectance Ultra wide viewing angle Ultra low power consumption Pure reflective mode Bi-stable Commercial temperature range Landscape, portrait mode Antiglare hard-coated front-surface 3. Mechanical Specifications Parameter Screen Size Display Resolution Active Area Pixel Pitch Pixel Configuration Outline Dimension Module Weight Specifications 5 800 (H) 600(V) 101.6 (H) 76.2 (V) 0.127(H)x0.127(V) Rectangle 114.6(H) 89.6(V) 1.18(D) (panel area height) 114.6(H) 89.6(V) 2.0(D) (FPC area height with capacitor) 24 2 Unit Inch Pixel mm mm Remark mm g Panel height is measured without released film The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:4 ED050SC3 4. Mechanical Drawing of EPD Module The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:5 ED050SC3 5. Input/Output Terminals 5-1)Pinout List Pin # Signal Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 VNEG NC VPOS NC VSS NC VDD XCL XLE XOE XSHR XSTL2 D0 D1 D2 D3 D4 D5 D6 D7 NC VCOM NC VGG NC VEE NC MODE2 MODE1 XRL SPV CKV BORDER Negative power supply source driver NO Connection Positive power supply source driver NO Connection Ground NO Connection Digital power supply drivers Clock source driver Latch enable source driver Output enable source driver Shift direction source driver Start pulse source driver Data signal source driver Data signal source driver Data signal source driver Data signal source driver Data signal source driver Data signal source driver Data signal source driver Data signal source driver NO Connection Common connection NO Connection Positive power supply gate driver NO Connection Negative power supply gate driver NO Connection Output mode selection gate driver Output mode selection gate driver Shift direction gate driver Start pulse 1st gate driver Clock 1st gate driver Border connection The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:6 ED050SC3 6.Electrical Characteristics 6-1) Panel interface description This panel is driven by ASIC PVI-6001A or “Apollo” display controller ASIC. See control product specification for details. 6-2) Absolute maximum rating Parameter Logic Supply Voltage Positive Supply Voltage Negative Supply Voltage Max .Drive Voltage Range Supply Voltage Supply Voltage Supply Range Operating Temp. Range Storage Temperature Symbol VDD VPOS VNEG VPOS - VNEG VGG VEE VGG-VEE TOTR TSTG Rating -0.3 to +7 -0.3 to +18 +0.3 to -18 36 -0.3 to +45 -25.0 to +0.3 -0.3 to +45 0 to +50 -25 to +70 Unit V V V V V V V 6-3) Panel DC characteristics Parameter Signal ground Logic Voltage supply Gate Negative supply Gate Positive supply Source Negative supply Source Positive supply Border supply Asymmetry source Common voltage Maximum power panel Standby power panel Typical power panel Operating temperature Storage temperature Maximum image update time at 25 Symbol VSS VDD IVDD VEE IEE VGG IGG VNEG INEG VPOS IPOS VBorder VAsym VCOM ICOM PMAX PSTBY PTYP VPOS = 15V VPOS = 15V VNEG = -15V VPOS+VNEG VNEG = -15V VGG = 22V VEE =-20V VDD=3.3V Conditions Min 3.0 -21 21 -15.4 14.6 14.6 -15.4 -800 -2.5 0 -25 Typ 0 3.3 0.5 -20 5 22 1.4 -15 22 15 24 15 -15 0 Adjusted 0.25 850 1000 Max 3.6 1 -19 15 23 4.2 -14.6 44 15.4 48 15.4 -14.6 800 -1.0 1850 0.4 50 70 ms Unit V V mA V mA V mA V mA V mA V V mV V mA mW mW mW The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:7 ED050SC3 The maximum power and maximum currents are specified for the worse case power consumption. This occurs when 2 horizontal inverted stripped images are displayed The typical power is the consumed power when “typical images” are displayed. The standby power is the consumed power when the panel controller is in standby mode. The listed electrical/optical characteristics are only guaranteed under the controller & waveform provided by PVI - Vcom is recommended to be set in the range of assigned value 0.1V 6-4 )Panel AC characteristics VDD=3.0V to 3.6V, unless otherwise specified. Parameter Clock frequency Minimum “L” clock pulse width Clock rise time Clock fall time Data setup time Data hold time Pulse rise time Pulse fall time Clock CL cycle time D0 .. D7, SPH setup time D0 .. D7, SPH LE LE LE on off hold time delay time delay time Symbol fckv twL trckv tfckv tSU tH trspv tfspv tcy tsu th tLEdly tLEw tLEoff Min. 0.5 100 100 50 8 1 40 40 40 Typ. Max. 200 100 100 100 100 DC Unit kHz us ns ns ns ns ns ns ns ns ns ns ns ns Below table CKV, SPV SPV CKV App Pin high-level pulse width CLOCK & DATA TIMING CL tLEdly LE tLE tLEoff tOUT OUT1 ~ OUT400 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:8 ED050SC3 OUTPUT LATCH CONTROL SIGNALS SPH 10% tstls tstlh 10% CL tcy 90% D0~D7 10% 90% 10% tsu th tfckv twl trckv 90 CKV 90 10 10 tus tfspv th SPV trspv 90 90 10 10 6-5) Power Consumption Parameter Maximum panel power consumption during update. Power consumption in standby mode Typical panel power Symbol Conditions TYP Max 850 1850 0.4 - Unit mW mW mW Remark The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:9 ED050SC3 7.Power on Sequence 1. VSS 2. VEE VDD VNEG VPOS (Source driver) VGG(Gate driver) Power on sequence’s timing chart as blew : VGG V POS T1 T2 T3 T4 T5 T6 T7 VDD VSS VEE V NEG Logic signal input T1: 100 µs(min) T2: 0µs(min) T3: 1000µs (min) T4: 0 µs ( min) T5: 0 µs (min) T6: 0 µs (min) T7: 0 µs (min) The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:10 ED050SC3 It is expanded as blew. VDD Sequence VPOS Sequence VNEG Sequence VEE Sequence VGG Sequence Logic signal input Sequence The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:11 ED050SC3 8. Optical characteristics 8-1)Specifications Measurements are made with that the illumination is under an angle of 30 degrees, the detection is perpendicular unless otherwise specified. T = 25oC SYMBOL R Gn CR Tupdate PARAMETER Reflectance Nth Grey Level Contrast Ratio Update time CONDITIONS White 2~4-bit mode 1-bit mode MIN 30 6 TYP. MAX ms ms UNIT % L* 35 DS+(WS-DS) n/(m-1) 1000 540 Note - WS: White state , DS: Dark state, Gray state from Dark to White :DS m:4 8 16 when 2 3 4 bits mode G1 G2… Gn… Gm-2 WS 8-2)Definition of contrast ratio The contrast ratio (CR) is the ratio between the reflectance in a full white area (Rl) and the reflectance in a dark area (Rd): CR = Rl/Rd The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:12 ED050SC3 8-3)Reflection Ratio The reflection ratio is expressed as: R = Reflectance Factorwhite board x ( Lcenter / Lwhite board ) Lcenter is the luminance measured at center in a white area (R=G=B=1). Lwhite board is the luminance of a standard white board. Both are measured with equivalent illumination source. The viewing angle shall be no more than 2 degrees. α = declination / θ = azimuth The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:13 ED050SC3 9.HANDLING, SAFETY AND ENVIROMENTAL REQUIREMENTS WARNING The display glass may break when it is dropped or bumped on a hard surface. Handle with care. Should the display break, do not touch the electrophoretic material. In case of contact with electrophoretic material, wash with water and soap. CAUTION The display module should not be exposed to harmful gases, such as acid and alkali gases, which corrode electronic components. Disassembling the display module can cause permanent damage and invalidate the warranty agreements. Observe general precautions that are common to handling delicate electronic components. The glass can break and front surfaces can easily be damaged. Moreover the display is sensitive to static electricity and other rough environmental conditions. Data sheet status Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:14 ED050SC3 10. Reliability test TEST 1 2 3 4 5 6 7 8 9 High-Temperature Operation Low-Temperature Operation High-Temperature Storage Low-Temperature Storage High-Temperature, High-Humidity Operation High Temperature, High- Humidity Storage Temperature Cycle UV exposure Resistance Package Vibration CONDITION T = +50°C, RH = 30% for 240 hrs T = 0°C for 240 hrs T = +70°C, RH=23% for 240 hrs T = -25°C for 240 hrs T = +40°C, RH = 90% for 168 hrs T = +50 , RH=80% for 240hrs 1 cycle:[-25 30min] [+70 min] :100 cycles 765 W/m for 168hrs,40 1.04G, Frequency: 10~500Hz Direction: X,Y,Z Duration: 1 hours in each direction Drop from height of 122 cm on concrete surface. Drop sequence: 1 corner, 3 edges, 6 faces One drop for each. 2 METHOD IEC 60 068-2-2Bp IEC 60 068-2-2Ab IEC 60 068-2-2Bp IEC 60 068-2-1Ab IEC 60 068-2-3CA IEC 60 068-2-3CA REMARK 30 At the end of the test, electric, mechanical, and optical specifications shall be satisfied. At the end of the test, electric, mechanical, and optical specifications shall be satisfied. At the end of the test, electric, mechanical, and optical specifications shall be satisfied. At the end of the test, electric, mechanical, and optical specifications shall be satisfied. At the end of the test, electric, mechanical, specifications shall be satisfied. At the end of the test, electric, mechanical, specifications shall be satisfied. At the end of the test, electric, mechanical, IEC 60 068-2-14 specifications shall be satisfied. IEC60 068-2-5Sa Optical characteristics shall be satisfied. Full packed for At the end of the test, electric, mechanical, shipment and optical specifications shall be satisfied. 10 Package Drop Impact Full packed for At the end of the test, electric, mechanical, shipment and optical specifications shall be satisfied. 11 Electrostatic Effect (non-operating) (Machine model)+/- 250V 0 , 200pF IEC 62179, IEC At the end of the test, electric, mechanical, 62180 specifications shall be satisfied. 12 Altitude test Operation 700hPa ( = 3000m )48Hr At the end of the test, electric, mechanical, specifications shall be satisfied. 13 Altitude test Storage 260hPa ( = 10000m )48Hr POLYACETAL Pen: Top R:0.8mm Load: 300gf Speed: 2 times/sec Total 13,500times, At the end of the test, electric, mechanical, specifications shall be satisfied. Pass criteria – no glass breakage or damage to microcapsules. 14 Stylus Tapping Actual EMC level to be measured on customer application The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:15 ED050SC3 11. Bar Code definition E0Y 1 1 2 3 4 5 6 7 8 00 2 4 3 01 4 1 2 I 5 6 7 4 2 00361 7 2 A 8 T EPD model code: ED050SC3:E0Y Internal control codes: FPL reversion code V100:3,V110:4 FPL batch code: (BL/P/B...)001~009:01~99, 100~109:A0~A9, 110-119:B0~B9… 320~329:Z0~Z9 Year: F:2005 / G:2006 / H:2007 / I:2008 /... / Z:2025 Month: 1:Jan. 2:Feb. ... 9:Sep. A:Oct. B:Nov. C:Dec. Serial number MFG code: TOC:T, PVI:P The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:16 ED050SC3 12. Border definition 13.Block Diagram 33 PIN Input The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:17 ED050SC3 14.Packing The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:18