PD057VU4

P-511-361(V:5) Version : 5.0 PD057VU4 TECHNICAL SPECIFICATION MODEL NO. : PD057VU4 The content of this information is subject to be changed without notice. Please contact PVI or its agent for further information. Customer’s Confirmation Customer Date FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA 92656 Http://www.AZDISPLAYS.com By Confirmed By Prepared By The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:1 Ver:5 1/19 P-511-361(V:5) PD057VU4 Revision History Rev. Issued Date 1.0 Jul.11, 2006 2.0 Oct. 23, 2006 Revised New Contents 3.0 4.0 5.0 Page 16 Low Temperature Storage Test -30 -40 Low Temperature Operation Test -20 -30 Feb. 05, 2007 Page 3 Optimum Viewing Direction 6 o’clock Add March.24.2008 Page 16 13.Handling Cautions 13-1 item e) Jun. 09. 2008 Modify Page 5 Packing Drawing---add UL Label The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:2 Ver:5 2/19 P-511-361(V:5) PD057VU4 TECHNICAL SPECIFICATION CONTENTS NO. - ITEM Cover Revision History Contents Application Features Mechanical Specifications Mechanical Drawing of TFT-LCD module Input / Output Terminals Absolute Maximum Ratings Electrical Characteristics Pixel Arrangement Display Color and Gray Scale Reference Interface Timing Power On Sequence Optical Characteristics Handling Cautions PAGE 1 2 3 4 4 4 4 6 7 7 8 9 10 13 13 16 18 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Reliability Test Packing Diagram The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:3 Ver:5 3/19 P-511-361(V:5) PD057VU4 1. Application This data sheet applies to a color TFT LCD module, PD057VU4. PD057VU4 module applies to OA product, car TV (must use Analog to Digital driving board), which requires high quality flat panel display. If you must use in severe reliability environment, please don’t extend over PVI’s reliability test conditions. 4. Features . QVGA (320*240 pixels) resolution . Amorphous silicon TFT LCD panel with back-light unit . Pixel in stripe configuration . Thin and light weight . Display Colors 262,144 colors . TTL interface 4. Mechanical Specifications Parameter Screen Size Display Format Display Colors Active Area Pixel Pitch Pixel Configuration Outline Dimension W eight Back-light Surface treatment Display mode Gray scale inversion direction Specifications 5.7 (diagonal) 320 (R,G,B) 240 262,144 115.20 (H) 86.4 (V) 0.36(H) 0.36(V) Stripe 144(W) 104.6 (H) 13.0 (D) (typ.) 202 10 CCFL, 1 tube Anti-glare + wide view film Normally white 6 o`clock [ref to Note 12-1] Unit inch dot mm mm mm g The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:4 Ver:5 4/19 P-511-361(V:5) PD057VU4 4.Mechanical Drawing of TFT-LCD Module Outline Drawing : Front View (unit : mm) The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:5 E307459 Ver:5 5/19 P-511-361(V:5) PD057VU4 5.Input / Output Terminals 5-1) TFT-LCD Panel Driving Connector type: ELCO 08-6210-033-340-800A+ , PIN No 33 pins, pitch=0.5mm Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Symbol I/O GND I CK I Hsync I Vsync GND R0 I R1 I R2 I R3 I R4 I R5 GND I G0 I G1 I G2 I G3 I G4 I G5 GND I B0 I B1 I B2 I B3 I B4 I B5 GND I ENAB VCC VCC Description GND Clock signal for sampling each data signal Horizontal synchronous signal(neqative) Vertical synchronous signal(neqative) GND RED data signal(LSB) RED data signal RED data signal RED data signal RED data signal RED data signal(MSB) GND GREEN data signal(LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal(MSB) GND Blue data signal(LSB) Blue data signal Blue data signal Blue data signal Blue data signal Blue data signal(MSB) GND Signal to settle the horizontal display position(positive) +3.3V power supply +3.3V power supply Horizontal display mode select signal L Normal ,H Left /Right reverse mode Vertical display mode select signal H Normal ,L :Up/Down reverse mode VGA / QVGA mode select signal GND Remark Note5-1 30 R/L I Note5-2 31 U/D I Note5-3 32 33 V/Q GND I - Note10-2 Note5-1 The horizontal display start timing is settled in accordance with rising of ENAB signal. In case ENAB is fixed ”Low”,the horizontal start timing is determined as described in 10-2. Don`t keep ENAB”High” during operation. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:6 Ver:5 6/19 P-511-361(V:5) PD057VU4 Note 5-2 , 5-3 : The definitions of U/D & R/L R/L(PIN 30)= Low, U/D(PIN 31)= High R/L(PIN 30)= High , U/D(PIN 31)= Low 5-2) Backlight driving Connector type: JST BHR-03VS-1, PIN No 2 pins, pitch=3.5mm Pin No Symbol Description Remark 1 VHigh Power supply for lamp (High voltage side) Red - NC This is electrically opened - 3 VLow Power supply for lamp (Low voltage side) White Note 5-11: Low voltage side of backlight inverter connects with ground of inverter circuits. 6.Absolute Maximum Ratings: Parameters Input Voltage Symbol VI Condition MAX. GND=0V, Ta=25 Unit V Remark Note6-1 Ta=25 -0.3~+4 Ta=25 +3.3V supply voltage VCC 0~+3.6 V Note6-1:CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB,R/L,U/D,V/Q 7.Electrical Characteristics 7-1) Recommended Operating Conditions: Item +3.3V Supply Voltage Symbol VCC Min. Typ. GND=0V, Ta=25 Max. Unit Remark V mVp-p VCC=3.3V V V +3.0 0 0.7 VCC +3.3 - +3.6 100 0.3 VCC VCC Permissive input ripple voltage Input voltage(Low) Input voltage(High) VRF VIL VIH The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:7 Ver:5 7/19 P-511-361(V:5) PD057VU4 7-2) Recommended Driving Condition for Back Light Ta=25 Parameter Symbol Min. Typ. Max. Unit Remark Lamp Voltage VL 639 710 781 V IL=5mA Lamp Current IL 4 5 8 mA Note 7-1 Lamp Frequency PL KHz Note 7-2 35 Vs Vrms Note 7-3 Starting Voltage (25 ) 1240 (Reference Value) Vrms Note 7-3 Vs Starting Voltage (0 ) 1380 (Reference Value) Note 7-1 In order to have proper operation of the B/L, no matter what kind of inverters, the output lamp current must be between Min. and Max. values to avoid the abnormal display image caused by B/L. Note 7-2 The driving frequency of the lamp may interfere with the horizontal synch signal, leaving interference stripes on the display. So please evaluate LCD panels beforehand. To avoid interference stripes, we recommend to separate as far as possible the lamp frequency from the horizontal synchronous signal and its high harmonic frequency. The inverter which PVI uses is TAD347-1. Note 7-3 The “Starting Voltage” means the minimum voltage of inverter to turn on the lamp. And it should be applied to the lamp for more than 1 second to start up. Otherwise the lamp may not be turned on. 7-3) Power Consumption Parameters +3.3V Current Dissipation LCD Panel Power Consumption Symbol ICC - Typ. 67 0.22 Max. 75 0.25 Unit mA W Remark Note 7-4 Backlight Power Consumption - 3.55 3.91 W Note 7-5 Note 7-4: The power consumption for back light is not included. Note 7-5: Back light lamp power consumption is calculated by IL VL. 8. Pixel Arrangement The LCD module pixel arrangement is stripe configuration. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:8 Ver:5 8/19 P-511-361(V:5) PD057VU4 9. Display Color and Gray Scale Reference Color Red Input Color Data Green Blue R5 R4 R3 R2 R1 R0 G 5 G 4 G 3 G 2 G 1 G 0 B5 B4 B3 B2 B1 B0 Basic Colors Black Red (63) Green (63) Blue (63) Cyan Magenta Yellow W hite Red (00) Red (01) Red (02) Darker 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 Red Brighter Red (61) Red (62) Red (63) Green (00) Green (01) Green (02) Darker 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Green Brighter Green (61) Green (62) Green (63) Blue (00) Blue (01) Blue (02) Darker 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 Blue Brighter Blue (61) Blue (62) Blue (63) 000000000000111101 000000000000111110 000000000000111111 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:9 Ver:5 9/19 P-511-361(V:5) PD057VU4 10. Interface Timing 10-1) Timing Parameters AC Electrical Characteristics (VCC =+3.3V,GND=0V,Ta=25 Characteristics Symbol Min. Typ. 25.18 ) Max. 28.33 Unit MHz Remark Clock Frequency 1/Tc V/Q=H Data Duty ratio Set up time Hold time Tch/Tc Tds Tdh TH Horizontal sync. Signal Cycle TH Pulse width Vertical sync. Signal Cycle Pulse width line Horizontal display period Clock Hsync.-Clock phase difference 10 Tc-10 ns Hsync.-Vsync. Phase 0 TH-THp ns difference Vertical sync. Signal start 34 V/Q=H TVs line position 7 V/Q=L Note10-1 In case of lower frequency, the deterioration of the display quality, flicker etc., may occur. THp TV TV TVp THd THc TVh 40 5 10 30.0 700 50.0 360 2 515 251 2 6.3 50 31.8 800 63.6 400 96 525 262 320 - 7.0 60 900 450 200 560 280 34 MHz % V/Q=L V/Q=L ns us clock us clock clock V/Q=H V/Q=L line V/Q=H V/Q=L Parameter symbol Min. Typ Max Unit Remark Enable Set up time Tes 5 Tc-10 ns signal Pulse width Tep 2 320 TH-10 clock 44 TH-664 V/Q=H Hsync-Enable signal The clock phase difference 2 TH-340 V/Q=L Note10-2 W hen ENAB is fixed at “V/Q=Low”, the display starts from the data of C52 (clock). When ENAB is fixed at “V/Q=High”, the display starts from the data of C104 (clock). The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:10 Ver:5 10/19 P-511-361(V:5) PD057VU4 10-2) Timing Diagram The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:11 C1 Ver:5 11/19 P-511-361(V:5) TV TVp 0.7VDD 0.3VDD 0.3VDD Vertical sync.Signal(Vsync) TVh 0.7VDD Horizontal 1line 2line sync.Signal(Hsync) Nline*2 TVs TVd Data Verticla invalid data period signal(R0~R5,G0~G5, DH1 DH2 DH240 Verticla invalid data period The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:12 *2 The vertical display position (TVs) is fixed at 34th line (V/Q=H) and 7th line (V/Q=L). PD057VU4 B0~B5) Ver:5 12/19 P-511-361(V:5) PD057VU4 11. Power On Sequence VDD 3.0V Signal*3 3.0V 0.3V t1 t2 t3 OFF 10ms Back Light ON 10ms OFF 1. 0 2. 0 3. 0 t1 t2 t3 20ms 50ms 1s 12. Optical Characteristics 12-1) Specification: Parameter Symbol Horizontal Condition MIN. TYP. MAX. Ta=25 Unit Remarks deg Note 12-1 55 CR 10 60 - Viewing Angle Vertical (to 6 o’clock) (to 12 o’clock) 45 50 - deg 35 40 - deg Contrast Ratio CR At optimized viewing angle 200 400 - - Note 12-2 Response time Rise Tr Fall Tf =0 - 15 30 ms =0 25 Brightness - =0°/ 450 500 50 - ms Note 12-3 cd/ Note 12-4 Luminance Uniformity U% 75 80 - % Note 12-5 W hite Chromaticity x 0.29 0.32 0.35 - y Lamp Life Time - 0.33 0.36 0.39 50000 - - hr At=5mA The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:13 Ver:5 13/19 P-511-361(V:5) PD057VU4 Note 12-1: The definitions of viewing angles are as follow 12 o clock Lamp connector θ 3 o clock 9 o clock φ Note 12-2: The definition of contrast ratio 6 o clock = Note 12-3: Definition of Response Time Tr and Tf: W hite Black W hite 1 00% 90% The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:14 Brightness 10% 0% Tr Tf Ver:5 14/19 P-511-361(V:5) PD057VU4 Note 12-4: All optical measurements shall be performed after backlight being turned-on for 30 mins. The optical characteristics shall be measured in dark room (ambient illumination on panel surface less than 1 Lux). The measuring configuration shows as following figure. Photometer (TOPCON BM-5A or BM-7 fast) Note 12-5: The uniformity of LCD is defined as U= The Minimum Brightness of the 9 testing Points The Maximum Brightness of the 9 testing Points Luminance meter: BM-5A or BM-7 fast (TOPCON) Measurement distance: 500 mm +/- 50 mm Ambient illumination: < 1 Lux Measuring direction: Perpendicular to the surface of module The test pattern is white (Gray Level 63). 500 mm +/- 50 mm 1/6 2/6 Field = 1° TFT-LCD module DC/AC Inverter Optical characteristics measuring configuration 1 /6 2/6 2/6 1/6 2/6 1/6 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:15 Ver:5 15/19 P-511-361(V:5) PD057VU4 13. Handling Cautions 13-1) Mounting of module a)Please power off the module when you connect the input/output connector. b)Please connect the ground pattern of the inverter circuit surely. If the connection is not perfect, some following problems may happen possibly. 1. The noise from the backlight unit will increase. 2. The output from inverter circuit will be unstable. 3. In some cases a part of module will heat. c)Polarizer which is made of soft material and susceptible to flaw must be handled carefully. d)Protective film (Laminator) is applied on surface to protect it against scratches and dirt. e)Please following the tear off direction as figure13-1 to remove the protective film as slowly as possible, so that electrostatic charge can be minimized. 13-2) Precautions in mounting a) When metal part of the TFT-LCD module (shielding lid and rear case) is soiled, wipe it with soft dry cloth. b) Wipe off water drops or finger grease immediately. Long contact with water may cause discoloration or spots. c) TFT-LCD module uses glass which breaks or cracks easily if dropped or bumped on hard surface. Please handle with care. d) Since CMOS LSI is used in the module. So take care of static electricity and earth yourself when handling. 13-3) Adjusting module a) Adjusting volumes on the rear face of the module have been set optimally before shipment. b) Therefore, do not change any adjusted values. If adjusted values are changed, the specifications described may not be satisfied. 13-4) Others a) Do not expose the module to direct sunlight or intensive ultraviolet rays for many hours. b) Store the module at a room temperature place. c) The voltage of beginning electric discharge may over the normal voltage because of leakage current from approach conductor by to draw lump read lead line around. d) If LCD panel breaks, it is possibly that the liquid crystal escapes from the panel. Avoid putting it into eyes or mouth. When liquid crystal sticks on hands, clothes or feet. Wash it out immediately with soap. e) Observe all other precautionary requirements in handling general electronic components. f) Please adjust the voltage of common electrode as material of attachment by 1 module. 13-5) Polarizer mark The polarizer mark is to describe the direction of wide view angle film how to match up with the rubbing direction. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:16 Ver:5 16/19 P-511-361(V:5) PD057VU4 Figure 13-1 the way to peel off protective film The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:17 Ver:5 17/19 P-511-361(V:5) PD057VU4 14. Reliability Test No Test Item Test Condition Remark 1 High Temperature Storage Test Ta = +80 , 240 hrs 2 Low Temperature Storage Test Ta = -40 , 240 hrs 3 High Temperature Operation Test Ta = +70 , 240 hrs 4 Low Temperature Operation Test Ta = -30 , 240 hrs 5 High Temperature & High Humidity Ta = +60 , 90%RH, 240 hrs Operation Test (No Condensation) 6 Thermal Cycling Test (non-operating) -20 +70 , 200 Cycles Vibration Test 7 (non-operating) Shock Test 8 (non-operating) 30 min 30 min Frequency: 10 ~ 57 HZ /Vibration Width:0.075mm 2 58-500 Hz / Gravity: 9.8m/s Sweep time: 11 minutes Test period: 3 hrs for each direction of X, Y, Z 2 Gravity: 490m/s * 6ms Direction: X, Y, Z 3 times for each direction Electrostatic Discharge Test 9 (non-operating) Machine Mode = 200V C = 200pF , R = 0 1 times discharge for each pad Ta: ambient temperature Note: The protective film must be removed before temperature test [Criteria] In the standard conditions, there is not display function NG issue occurred. (Including line defect, no image) All the cosmetic specification is judged before the reliability stress. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:18 Ver:5 18/19 P-511-361(V:5) PD057VU4 15. Packing Diagram The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:19 Ver:5 19/19