PD057VU7

P-511-508(V:4) PD057VU7 FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA 92656 Http://www.AZDISPLAYS.com By Confirmed By Prepared By The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:1 P-511-508(V:4) PD057VU7 Revision History Rev. Issued Date 1.0 May 15, 2008 Eng. Revised Contents New Delete backlight connector pin pitch Before Connector type JST BHR-03VS-1, PIN No 2 pins, pitch=3.5mm After Connector type JST BHR-03VS-1, PIN No 3 pins Icc Max. from 100mA to 75mA LCD Panel Power Consumptio Max. from 0.33W to 0.25W Total Power Consumption Max. from 2.97W to 2.89W 2.0 May 19, 2009 3.0 4.0 Jun. 19, 2009 Jul. 3, 2009 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:2 P-511-508(V:4) PD057VU7 TECHNICAL SPECIFICATION CONTENTS NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ITEM Cover Contents Revision History Application Features Mechanical Specifications Mechanical Drawing of TFT-LCD module Input / Output Terminals Touch Panel Characteristics Absolute Maximum Ratings Electrical Characteristics Pixel Arrangement Display Color and Gray Scale Reference Interface Timing Power On Sequence Optical Characteristics Handling Cautions PAGE 1 2 3 4 4 4 5 6 7 9 9 10 11 12 15 15 18 19 20 Reliability Test Packing Diagram The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:3 P-511-508(V:4) PD057VU7 1. Application This data sheet applies to a color TFT LCD module, PD057VU7. PD057VU7 module applies to OA product, car TV (must use Analog to Digital driving board), which requires high quality flat panel display. If you must use in severe reliability environment, please don’t extend over PVI’s reliability test conditions. 2. Features . QVGA (320*240 pixels) resolution . Module with resistive type touch panel . Amorphous silicon TFT LCD panel with LED . Pixel in stripe configuration . Thin and light weight . Display Colors 262,144 colors . TTL interface 3. Mechanical Specifications Parameter Screen Size Display Format Display Colors Active Area Pixel Pitch Pixel Configuration Outline Dimension W eight Back-light Surface treatment Display mode Surface treatment of Touch Panel Gray scale inversion direction Specifications 5.7 (diagonal) 320 (R,G,B) 240 262,144 115.20 (H) 86.4 (V) 0.36(H) 0.36(V) Stripe 144(W) 104.6 (H) 14.45 (D) (typ.) 244 10 36-LED Anti-glare + SWV Normally white 3H 6 o`clock [ ref. to Note 13-1 ] Unit inch dot mm mm mm g The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:4 P-511-508(V:4) PD057VU7 4.Mechanical Drawing of TFT-LCD Module Outline Drawing : Front View (unit : mm) The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:5 E307459 P-511-508(V:4) PD057VU7 5.Input / Output Terminals 5-1) TFT-LCD Panel Driving Connector type: ELCO 08-6210-033-340-800A+, PIN No 33 pins Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Symbol I/O GND I CK I Hsync I Vsync GND R0 I R1 I R2 I R3 I R4 I R5 GND I G0 I G1 I G2 I G3 I G4 I G5 GND I B0 I B1 I B2 I B3 I B4 I B5 GND I ENAB VCC VCC R/L U/D V/Q GND I I I Description GND Clock signal for sampling each data signal Horizontal synchronous signal(neqative) Vertical synchronous signal(neqative) GND RED data signal(LSB) RED data signal RED data signal RED data signal RED data signal RED data signal(MSB) GND GREEN data signal(LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal(MSB) GND Blue data signal(LSB) Blue data signal Blue data signal Blue data signal Blue data signal Blue data signal(MSB) GND Signal to settle the horizontal display position(positive) +3.3V power supply +3.3V power supply Horizontal display mode select signal L Normal ,H Left /Right reverse mode Vertical display mode select signal H Normal ,L :Up/Down reverse mode VGA / QVGA mode select signal GND Remark Note5-1 Note5-2 Note5-3 Note11-2 Note5-1 The horizontal display start timing is settled in accordance with rising of ENAB signal. In case ENAB is fixed ”Low”,the horizontal start timing is determined as described in 10-2. Don`t keep ENAB”High” during operation. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:6 P-511-508(V:4) PD057VU7 Note 5-2 , 5-3 The definitions of U/D & R/L R/L(PIN 30)= Low, U/D(PIN 31)= High R/L(PIN 30)= High , U/D(PIN 31)= Low 5-2) LED Backlight driving Connector type: JST BHR-03VS-1, PIN No 3 pins Pin No 1 2 3 Symbol + NC Description Remark Red Black Input terminal (Anode) No connect Input terminal (Cathode) 6.Touch Panel Characteristics 6-1) Pin assignment Pin No. 1 2 3 4 Designation YU (Bottom) XL (Top) YL (Botton) XR (Top) Remark The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:7 P-511-508(V:4) PD057VU7 6-2) Electrical Performance Parameters Terminal Resistance Input Voltage Linearity (X ,Y direction) Insulation Impedance Response Time Operation Force Symbol X Y VT MIN. 400 230 20 Typ. 550 320 5 MAX. 810 540 7 ±1.5 15 50 Unit Ω Ω V % MΩ ms g Remark DC 25V Note 6-1 Note 6-1 Input through R0.8mm stylus or R8.0mm finger. 6-3) Durability Performance 1. Hitting Durability: At least 1,000,000 times with R8.0mm silicon rubber, 250g, 3 times/sec. 2. Sliding Durability: At least 1,00,000 times with R0.8mm polyacetal stylus, 250g, 60 mm/sec. 6-4) Integration Design Guide Avoid the design that Front-case overlap and press on the active area of the touch-panel. Give enough gap (over 0.5mm at compressed) between the front case and touch-panel to protect wrong operating. Use a buffer material (Gasket) between the touch-panel and front-case to protect damage and wrong operating. Avoid the design that buffer material overlap and press on the inside of touch-panel viewing area. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:8 P-511-508(V:4) PD057VU7 Note 6-2 We strongly suggest to follow above design guide to avoid the linear defect happened on the touch panel. 7.Absolute Maximum Ratings: Parameters Input Voltage Symbol VI Condition MAX. GND=0V, Ta=25 Unit V Remark Note7-1 Ta=25 -0.3~+4 Ta=25 +3.3V supply voltage VCC 0~+3.6 V Note7-1:CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB,R/L,U/D,V/Q 8.Electrical Characteristics 8-1) Recommended Operating Conditions: Item +3.3V Supply Voltage Permissive input ripple voltage Input voltage(Low) Input voltage(High) Symbol VCC VRF VIL VIH Min. Typ. GND=0V, Ta=25 Max. Unit V Remark +3.0 0 0.7 VCC +3.3 - +3.6 100 mVp-p VCC=3.3V 0.3 VCC V V VCC The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:9 P-511-508(V:4) PD057VU7 8-2) Recommended Driving Condition for LED Back Light Parameter LED voltage LED current Back Light Power Consumption Symbol VLED ILED PLED Min. Typ. 20 Max. (11) 2640 Unit V mA mW Ta=25 Remark Note 8-1 Note 8-2 Note 8-1 Note 8-3 Note 8-1 The ILED = 20 mA (Constant current) Note 8-2 The LED driving condition is defined for each LED module. (3 LED Serial) The input current= 20 mA*12=240 mA. Note 8-3 PLED = VLED-1 * ILED-1 + VLED-2* ILED-2 ….. + VLED-11 * ILED-11+VLED-12 * ILED-12 Anode Cathode 8-3) Power Consumption Parameters +3.3V Current Dissipation LCD Panel Power Consumption Total Power Consumption Symbol ICC - Typ. 67 0.22 - Max. 75 0.25 2.89 Unit mA W W Remark Note 8-4 Note 8-4 The power consumption for back light is not included. 9. Pixel Arrangement The LCD module pixel arrangement is stripe configuration. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:10 P-511-508(V:4) PD057VU7 10. Display Color and Gray Scale Reference Color Black Red (63) Green (63) Blue (63) Cyan Magenta Yellow W hite Red (00) Red (01) Red (02) Darker Brighter Red (61) Red (62) Red (63) Green (00) Green (01) Green (02) Darker Green Brighter Green (61) Green (62) Green (63) Blue (00) Blue (01) Blue (02) Darker Blue Brighter Blue (61) Blue (62) Blue (63) 000000000000111101 000000000000111110 000000000000111111 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 Red 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 1 0 1 0 0 0 1 1 1 0 1 0 Input Color Data Green 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 Blue 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 R5 R4 R3 R2 R1 R0 G 5 G 4 G 3 G 2 G 1 G 0 B5 B4 B3 B2 B1 B0 Basic Colors Red 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:11 P-511-508(V:4) PD057VU7 11. Interface Timing 11-1) Timing Parameters AC Electrical Characteristics (VCC =+3.3V,GND=0V,Ta=25 Characteristics Clock Frequency Symbol 1/Tc Min. 40 5 10 30.0 700 50.0 360 2 515 251 2 Typ. 25.18 ) Max. 28.33 Unit MHz Remark V/Q=H V/Q=L V/Q=L 6.3 7.0 MHz Duty ratio Tch/Tc 50 60 % Set up time Tds Data ns Hold time Tdh 31.8 us TH 800 900 clock Horizontal Cycle 63.6 us sync. signal TH 400 450 clock Pulse width THp 96 200 clock Vertical sync. TV 525 560 Cycle line signal TV 262 280 Pulse width TVp 34 line Horizontal display period THd 320 Clock Hsync.-Clock phase difference THc 10 Tc-10 ns Hsync.-Vsync. phase difference TVh 0 TH-THp ns Vertical sync. signal start 34 TVs line position 7 Note11-1 In case of lower frequency, the deterioration of the display quality, may occur. V/Q=H V/Q=L V/Q=H V/Q=L V/Q=H V/Q=L flicker etc., Parameter symbol Min. Typ Max Unit Remark Enable Set up time Tes 5 Tc-10 ns signal Pulse width Tep 2 320 TH-10 clock 44 TH-664 V/Q=H Hsync-Enable signal The clock phase difference 2 TH-340 V/Q=L Note11-2 W hen ENAB is fixed at “V/Q=Low”, the display starts from the data of C52 (clock). When ENAB is fixed at “V/Q=High”, the display starts from the data of C104 (clock). The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:12 P-511-508(V:4) THp TH Horizontal sync. 0.7VDD Signal 0.7VDD (Hsync) Tch Tcl Tc 0.3VDD 0.3VDD 11-2) Timing Diagram THc 0.7VDD Clock signal 0.3VDD 0.3VDD 0.3VDD 0.3VDD *1 CN 0.3VDD (CK) C1 0.3VDD Tds Tdh Number of H-data 0.7VDD D1 0.7VDD D2 Data signal (R0~R5,G0~G5, Horizontal invalid data period D320 Horizontal invalid data period B0~B5) The 0.7VDD Tes THd Data 0.3VDD Enable signal (ENAB) Tep The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:13 PD057VU7 *1 When ENAB is fixed at V/Q=”H”, the display starts from the data of C104 (Clock). When ENAB is fixed at V/Q=”L”, the display starts from the data of C52 (Clock). P-511-508(V:4) TV TVp 0.7VDD 0.3VDD 0.3VDD Verti cal sync. Signal(Vsync) TVh 0.7VDD Hori zontal 1li ne 2li ne Nline*2 sync. Signal(Hsync) TVs TVd Data Verticla i nvali d data period DH1 DH2 DH240 Verti cla i nvali d dat a period signal( R0~R5,G0~G5, The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:14 *2 The vertical display position (TVs) is fixed at 34th line (V/Q=H) and 7th line (V/Q=L). PD057VU7 B0~B5) P-511-508(V:4) PD057VU7 12. Power On Sequence VDD 3.0V 3.0V Signal*3 0.3V t1 t2 t3 OFF 10ms Back Light ON 10ms OFF 1. 0 2. 0 3. 0 t1 t2 t3 20ms 50ms 1s 13. Optical Characteristics 13-1) Specification: Parameter Symbol Horizontal Viewing Angle Vertical (to 6 o’clock) (to 12 o’clock) CR Tr Tf U% x y Condition MIN. TYP. MAX. Ta=25 Unit Remarks deg Note 13-1 deg deg ms ms cd/ % hrs Note 13-4 Note 13-2 Note 13-3 Note 13-5 Note 13-6 55 CR 10 60 50 40 600 15 25 600 85 0.31 30 50 0.35 0.38 - 45 35 Contrast Ratio Response time Brightness Luminance Uniformity W hite Chromaticity LED Life Time Rise Fall At optimized viewing angle =0 =0°/ =0 300 500 80 0.27 0.30 0.34 20000 - The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:15 P-511-508(V:4) PD057VU7 Note 13-1 The definitions of viewing angles are as follow LED Note 13-2 The definition of contrast ratio CR = Luminance at White Pattern Luminance at Black Pattern Note 13-3 Definition of Response Time Tr and Tf W hite 1 00% 90% Brightness 10% 0% Tr Tf Black W hite Note 13-4 The “LED Life time “ is defined as the module brightness decrease to 50% original Brightness that the ambient temperature is 25 and ILED = 240mA. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:16 P-511-508(V:4) PD057VU7 Note 13-5 All optical measurements shall be performed after backlight being turned-on for 30 mins. The optical characteristics shall be measured in dark room (ambient illumination on panel surface less than 1 Lux). The measuring configuration shows as following figure. Photometer (TOPCON BM-5A or BM-7 fast) Note 13-6 The uniformity of LCD is defined as U= The Minimum Brightness of the 9 testing Points The Maximum Brightness of the 9 testing Points Luminance meter: BM-5A or BM-7 fast (TOPCON) Measurement distance: 500 mm +/- 50 mm Ambient illumination: < 1 Lux Measuring direction: Perpendicular to the surface of module The test pattern is white. 500 mm +/- 50 mm 1/6 2/6 Field = 1° TFT-LCD module Optical characteristics measuring configuration 1 /6 2/6 2/6 1/6 2/6 1/6 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:17 P-511-508(V:4) PD057VU7 14. Handling Cautions 14-1) Mounting of module a) Please power off the module when you connect the input/output connector. b) Polarizer which is made of soft material and susceptible to flaw must be handled carefully. c) Protective film (Laminator) is applied on surface to protect it against scratches and dirts. d) Please following the tear off direction as figure 14-1 to remove the protective film as slowly as possible, so that electrostatic charge can be minimized. 14-2) Precautions in mounting a) When metal part of the TFT-LCD module (shielding lid and rear case) is soiled, wipe it with soft dry cloth. b) Wipe off water drops or finger grease immediately. Long contact with water may cause discoloration or spots. c) TFT-LCD module uses glass which breaks or cracks easily if dropped or bumped on hard surface. Please handle with care. d) Since CMOS LSI is used in the module. So take care of static electricity and earth yourself when handling. 14-3) Adjusting module a) Adjusting volumes on the rear face of the module have been set optimally before shipment. b) Therefore, do not change any adjusted values. If adjusted values are changed, the specifications described may not be satisfied. 14-4) Others a) Don`t expose the module to direct sunlight or intensive ultraviolet rays for many hours. b) Store the module at a room temperature place. c) The voltage of beginning electric discharge may over the normal voltage because of leakage current from approach conductor by to draw lump read lead line around. d) If LCD panel breaks, it is possibly that the liquid crystal escapes from the panel. Avoid putting it into eyes or mouth. When liquid crystal sticks on hands, clothes or feet. Wash it out immediately with soap. e) Observe all other precautionary requirements in handling general electronic components. f) Please adjust the voltage of common electrode as material of attachment by 1 module. 14-5) Polarizer mark The polarizer mark is to describe the direction of wide view angle film how to match up with the rubbing direction. Figure 14-1 the way to peel off protective film The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:18 P-511-508(V:4) PD057VU7 15. Reliability Test No Test Item Test Condition Ta = +85 , 240 hrs Ta = -40 , 240 hrs Ta = +80 , 240 hrs Ta = -30 , 240 hrs Remark 1 High Temperature Storage Test 2 Low Temperature Storage Test 3 High Temperature Operation Test 4 Low Temperature Operation Test 5 6 Operation Test Thermal Cycling Test (non-operating) High Temperature & High Humidity Ta = +60 , 90%RH, 240 hrs (No Condensation) -20 30 min +70 , 200 Cycles 30 min Vibration Test 7 (non-operating) Shock Test 8 (non-operating) Electrostatic Discharge Test 9 (non-operating) Hitting Durability Test (Touch panel) Sliding Durability Test 11 (Touch panel) 10 Frequency: 10 ~ 57 HZ /Vibration Width:0.075 mm 58-500 Hz / Gravity: 9.8m/s2 Sweep time: 11 minutes Test period: 3 hrs for each direction of X, Y, Z Gravity: 490m/s2 * 6ms Direction: X, Y, Z 3 times for each direction Machine Mode = 200V C = 200pF , R = 0 1 times discharge for each pad 1,000,000 times, with R 8.0 mm silicon rubber, 250g, 3times/sec 1,00,000 times, with R 0.8 mm polyacetal stylus, 250g, 60mm/sec Ta: ambient temperature Note: The protective film must be removed before temperature test [Criteria] In the standard conditions, there is not display function NG issue occurred. (Including line defect, no image) All the cosmetic specification is judged before the reliability stress. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:19 P-511-508(V:4) PD057VU7 16. Packing Diagram The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:20