AZ2500P2-1A-12DE

AZ2500 AZ 60 AMP LATCHING POWER RELAY FEATURES • • • • • • Low cost 60 Amp switching Heavy loads to 15000 VA 4 kV dielectric Epoxy sealed construction available UL, CUR file E43203 CONTACTS Arrangement Ratings SPST (1 Form A) Resistive load: Max. switched power: 15000 VA Max. switched current: 60 A Max. switched voltage: 400 VAC Rated Load UL, CUR Material Resistance 60 A at 250 VAC, 6k cycles, General Use 50 A at 250 VAC, 10k cycles, General Use 40 A at 250 VAC, 100k cycles, General Use Silver cadmium oxide or silver tin oxide < 50 milliohms initially (24 V, 1 A voltage drop method) GENERAL DATA Life Expectancy Mechanical Electrical Set and Reset Pulse Duration Set Time (typical) Reset Time (typical) Minimum operations 1 x 106 1 x 105 at 40 A 250 VAC Res. 50 ms minimum 20 ms at nominal coil voltage 20 ms at nominal coil voltage Dielectric Strength 4000 Vrms coil to contact (at sea level for 1 min.) 1500 Vrms between open contacts Insulation Resistance Creepage Distance 1000 megohms min. at 20°C, 500 VDC, 50% RH 8 mm At nominal coil voltage -40°C (-40°F) to 70°C (158°F) -40°C (-40°F) to 105°C (221°F) 0.062" DA at 10–55 Hz COIL Power At Pickup Voltage (typical) Temperature 666 mW single coil 1.3 W dual coil Max. 105°C (221°F) Ambient Temperature Operating Storage Vibration Shock Operating 20 g, 11 ms, 1/2 sine (no false operation) Non-Operating 100 g, 11 ms, 1/2 sine (no damage) Enclosure P.B.T. polyester Tinned copper alloy P. C. (coil), heavy tabs (power) 270°C (518°F) 5 seconds 33 grams NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 4. Allow suitable slack on leads when wiring, and do not subject the terminals to excessive force. Terminals Max. Solder Temp. Max. Solder Time Weight 10/26/06W AZ2500 AZ RELAY ORDERING DATA COIL SPECIFICATIONS -Standard Single Coil - Termination Style 1 Nominal Coil Must Operate Max. Continuous Coil Resistance VDC VDC VDC [1] ± 10% 5 4.0 6.5 24 6 4.8 7.8 35 9 7.2 11.7 80 12 9.6 15.6 145 24 19.2 31.2 575 48 38.4 62.4 2270 * Add suffix “K” for Coil Termination Style 2. For silver tin oxide contacts change “1A” to “1AE.” ORDER NUMBER* Unsealed AZ2500P1–1A–5D AZ2500P1–1A–6D AZ2500P1–1A–9D AZ2500P1–1A–12D AZ2500P1–1A–24D AZ2500P1–1A–48D Sealed AZ2500P1–-1A–5DE AZ2500P1–-1A–6DE AZ2500P1–-1A–9DE AZ2500P1–-1A–12DE AZ2500P1–-1A–24DE AZ2500P1–-1A–48DE COIL SPECIFICATIONS -Standard Dual Coil ORDER NUMBER* Sealed AZ2500P2–-1A–5DE AZ2500P2–-1A–6DE AZ2500P2–-1A–9DE AZ2500P2–-1A–12DE AZ2500P2–-1A–24DE AZ2500P2–-1A–48DE information. Nominal Coil Must Operate Max. Continuous Coil Resistance Unsealed VDC VDC VDC [1] ± 10% 5 4.0 6.5 12 AZ2500P2–1A–5D 6 4.8 7.8 17.5 AZ2500P2–1A–6D 9 7.2 11.7 40 AZ2500P2–1A–9D 12 9.6 15.6 72 AZ2500P2–1A–12D 24 19.2 31.2 285 AZ2500P2–1A–24D 48 38.4 62.4 1135 AZ2500P2–1A–48D NOTE: Relays may be ordered with twisted copper wire terminations (Styles A-K) as shown below. Contact factory for ordering [1] max. continuous voltage should not be applied for more than 30 seconds. * For silver tin oxide contacts change “1A” to “1AE.” MECHANICAL DATA Outline Dimensions PC Board Layout .751 [19.08] 3-Ø.047 [Ø1.20] .751 [19.08] .751 [19.08] 1.51 MAX [38.25] 1.000 [25.4] .850 [21.59] 1.000 [25.4] 3-Ø.047 [Ø1.20] .115 [2.93] 1.000 [25.4] .850 [21.59] 4-Ø.047 [Ø1.20] .115 [2.93] 1.20 MAX [30.25] .115 [2.93] .105 [2.67] .200 [5.08] .200 [5.08] .105 [2.67] .105 [2.67] AZ2500P1-Style 1 .031 .346 [8.80] .039 AZ2500P1-Style 2 (Bottom View) AZ2500P2 .315 Wiring Diagram Ø.138 [Ø3.50] 2x .364MAX .640MAX [16.25] [9.25] + Set polarity Reset polarity Set polarity Set coil (Contact close) + .142 [3.60] 0.025X0.025 [0.64X0.64] + - + Reset coil (Contact open) - + Reset polarity - + AZ2500P1-Style 1 AZ2500P1-Style 2 AZ2500P2 Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 10/26/06W AZ2500 AZ Weld style of twisted copper wire (A to K) A B C D E F G H K Notes: Weld figures for AZ2500 with twisted copper wire. Please show welding style (A to K) and the length of wires when ordering. Please note the length of each wire from left to right if the length is different. 10/26/06W