AZ2501P2-1A-48D

AZ2501 AZ 50 AMP LATCHING POWER RELAY FEATURES • • • • • • • Low cost 50 Amp switching Heavy loads to 13850 VA 4 kV dielectric Manual switch available Epoxy sealed version available UL, CUR file E44211 CONTACTS Arrangement Ratings SPST (1 Form A), 1C (SPDT) Resistive load: Max. switched power: 13850 VA Max. switched current: 50 A Max. switched voltage: 440 VAC UL/CUR 1 Form A (SPST) 50 A at 277 VAC, resistive, 100k cycles 5540 W at 277 VAC, Tungsten, 30k cycles 20A at 120 VAC, 277 VAC Ballast 20 FLA, 120 LRA at 120 VAC, 30k cycles 17 FLA, 102 LRA at 240 VAC, 30k cycles 14 FLA, 84 LRA at 277 VAC, 30k cycles 1 Form C (SPDT) 40 A at 277 VAC, General Use, 30k cycles Material Resistance Silver tin oxide < 50 milliohms initially (24 V, 1 A voltage drop method) GENERAL DATA Life Expectancy Mechanical Electrical Set and Reset Pulse Duration Set Time (typical) Reset Time (typical) Minimum operations 1 x 106 1 x 105 at 50 A 250 VAC Res. (SPST) 50 ms minimum 15 ms at nominal coil voltage 15 ms at nominal coil voltage Dielectric Strength 4000 Vrms coil to contact (at sea level for 1 min.) 1500 Vrms between open contacts Insulation Resistance Creepage Distance Ambient Temperature Operating Storage Vibration Shock Operating 10 g, 11 ms, 1/2 sine (no false operation) Non-Operating 100 g, 11 ms, 1/2 sine (no damage) 1000 megohms min. at 20°C, 500 VDC, 50% RH 8 mm At nominal coil voltage -40°C (-40°F) to 70°C (158°F) -40°C (-40°F) to 105°C (221°F) 0.062" DA at 10–55 Hz COIL Power At Pickup Voltage (typical) Temperature .96 W single coil 1.9 W dual coil Max. 105°C (221°F) Enclosure Terminals Max. Solder Temp. Max. Solder Time Weight P.B.T. polyester Tinned copper alloy 270°C (518°F) 5 seconds 32 grams NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 7/22/08W AZ2501 AZ RELAY ORDERING DATA COIL SPECIFICATIONS -Standard Single Coil Nominal Coil VDC 6 12 24 48 Must Operate VDC 4.8 9.6 19.2 38.4 Max. Continuous VDC [1] 7.8 15.6 31.2 62.4 Coil Resistance ± 10% 24 96 384 1536 ORDER NUMBER* 1 Form A AZ2501P1–1A–6D AZ2501P1–1A–12D AZ2501P1–1A–24D AZ2501P1–1A–48D 1 Form C AZ2501P1–-1C–6D AZ2501P1–-1C–12D AZ2501P1–-1C–24D AZ2501P1–-1C–48D COIL SPECIFICATIONS -Standard Dual Coil ORDER NUMBER* Nominal Coil Must Operate Max. Continuous Coil Resistance 1 Form A 1 Form C VDC VDC VDC [1] ± 10% 6 4.8 7.8 12 AZ2501P2–1A–6D AZ2501P2–-1C–6D 12 9.6 15.6 48 AZ2501P2–1A–12D AZ2501P2–-1C–12D 24 19.2 31.2 192 AZ2501P2–1A–24D AZ2501P2–-1C–24D 48 38.4 62.4 768 AZ2501P2–1A–48D AZ2501P2–-1C–48D * For epoxy sealed version (not allowed with manual switch) add suffix “E”. For manual switch add suffix “W”. For PCB retaining stud add suffix “K”. For reverse polarity coil add suffix “R”. NOTE: [1] Max. continuous voltage should not be applied for more then 30 seconds MECHANICAL DATA (Bottom View) Outline Dimensions PC Board Layout Suffix “W” only .601MAX [15.3] 1.547MAX [39.3] 0.177 [4.5] .376 [9.6] .472 [12.0] .167 [4.3] .295 [7.5] 1.083 [27.5] 3x .041 [1.04] .118 [3.0] .132 [3.35] .266 [6.8] 2 3 1.201MAX [30.5] 5 4 6 1 .143 [3.63] .205 [5.2] 3x .078 [1.98] .083 [2.1] Suffix “K” only .376 [9.6] .295 [7.5] .132 [3.35] .472 [12.0] .266 [6.8] 3 1.083 [27.5] .094 [2.4] 2 5 .167 [4.3] .024 [0.60] .031 [0.8] .394 [10.0] .024 [0.60] Suffix “K” only Terminal 5 omitted (single coil) 4 6 1 .059 [1.5] .063 [1.6] .094 [2.4] Terminal 6 omitted (form A) Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" .394 [10.0] 7/22/08W AZ2501 Wiring Diagram 4 4 4 4 3 3 3 6 3 6 1 2 1 2 152 15 2 SPST&Single Coil SPDT&Single Coil SPST&Double Coil SPDT&Double Coil NOTE: Regarding Standard Polarity type: 1. “Single Coil Latching Version” (1) After energizing 1 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is connected. (2) After energizing 2 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is disconnected. 2. “Double Coil Latching Version” (1) After energizing 5 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is connected. (2) After energizing 5 (+) and 2 (-) , 50ms pulse, terminal 3 and 4 is disconnected. Regarding Reverse Polarity type: 1. “Single Coil Latching Version” (1) After energizing 1 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is disconnected. (2) After energizing 2 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is connected. 2. “Double Coil Latching Version” (1) After energizing 5 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is disconnected. (2) After energizing 5 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is connected. 7/22/08W